Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2016.10–2019.09
RM32H0E _54 Brake _060039 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294918 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  ABS Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication. If any of the following is detected, the ABS warning light remains on:

·

The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).

·

There is a malfunction in the skid control ECU (brake actuator assembly) internal circuit.

·

There is an open in the harness between the combination meter and skid control ECU (brake actuator assembly).

·

The ABS is defective.


HINT:

In some cases, the GTS cannot be used when the skid control ECU (brake actuator assembly) is abnormal.


WIRING DIAGRAM

C367770E02
0.813,0.646 1.229,0.833 0.417,0.188 10 false CANL 0.781,1.25 1.198,1.438 0.417,0.188 10 false CANH 1.281,1.083 1.479,1.26 0.198,0.177 10 false 32 1.271,0.49 1.469,0.667 0.198,0.177 10 false 31 0.219,4.135 1.406,4.5 1.188,0.365 10 false Combination Meter Assembly 0.229,3.979 0.438,4.156 0.208,0.177 10 false F4 1.854,3.542 3.594,3.76 1.74,0.219 10 false : CAN Communication Line 1.781,4.406 4.167,4.625 2.385,0.219 10 false *2: w/o Stop and Start System 1.771,4.094 4.156,4.313 2.385,0.219 10 false *1: w/ Stop and Start System 2.885,1.708 3.698,1.927 0.813,0.219 10 false from Battery 2.292,2.375 3.667,2.604 1.375,0.229 10 false from IG1-NO. 1 Relay 1.875,2.865 3.625,3.073 1.75,0.208 10 false from Stop and Start System 4.406,1.885 5.167,2.094 0.76,0.208 10 false ABS-MAIN 4.281,2.563 5.323,2.76 1.042,0.198 10 false ECU-IG1 NO. 2 5.052,2.302 5.271,2.49 0.219,0.188 10 false *2 5.792,0.5 5.99,0.677 0.198,0.177 10 false 19 5.865,1.083 6.063,1.26 0.198,0.177 10 false 5 5.792,1.635 5.99,1.813 0.198,0.177 10 false 30 5.781,2.281 5.979,2.458 0.198,0.177 10 false 36 5.781,3.188 5.979,3.365 0.198,0.177 10 false 46 5.427,2.677 5.646,2.865 0.219,0.188 10 false *1 6.042,0.656 6.458,0.844 0.417,0.188 10 false CANL 6.042,1.25 6.458,1.438 0.417,0.188 10 false CANH 6.042,1.719 6.458,1.906 0.417,0.188 10 false +BS 6.052,2.396 6.469,2.583 0.417,0.188 10 false IG1 6.042,3.281 6.458,3.469 0.417,0.188 10 false GND1 5.604,4.125 7.146,4.531 1.542,0.406 10 false Skid Control ECU (Brake Actuator Assembly) 5.615,3.969 5.896,4.167 0.281,0.198 10 false A42

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform system variant learning.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.CHECK BATTERY

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:

11 to 14 V


Result:
Result Proceed to
OK A
NG (for 8NR-FTS) B
NG (for 3ZR-FAE) C




A

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE (IG1) TERMINAL)

B

CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY

C

CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE (IG1) TERMINAL)
a.
C360727C64
1.479,0.146 1.885,0.406 0.406,0.26 0.51,1.771 0.677,1.073 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 1.542,0.188 1.875,0.385 0.333,0.198 10 false A42 0.208,1.698 0.938,1.896 0.729,0.198 10 false +BS
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Disconnect the A42 skid control ECU (brake actuator assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-30 (+BS) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE (IG1) TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE (IG1) TERMINAL)
a.
C360727C65
1.5,0.167 1.906,0.427 0.406,0.26 1.469,0.927 0.813,0.219 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 1.573,0.208 1.906,0.406 0.333,0.198 10 false A42 0.573,0.135 1.208,0.323 0.635,0.188 10 false IG1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Disconnect the A42 skid control ECU (brake actuator assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-36 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Result Proceed to
OK A
NG (w/ Stop and Start System) B
NG (w/o Stop and Start System) C



A

6.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

6.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
C360727C05
0.063,0.302 0.5,0.552 0.438,0.25 2.427,0.313 2.771,0.958 true 0.135,0.063 0.448,0.26 0.313,0.198 10 false *a 0.146,0.333 0.458,0.531 0.313,0.198 10 false A42 2,0.229 2.5,0.438 0.5,0.208 10 false GND1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-46 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (ABS WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

7.READ VALUE USING GTS (ABS WARNING LIGHT)
a.

Reconnect the A42 skid control ECU (brake actuator assembly) connector.


b.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ABS Warning Light ABS warning light ON or OFF ON: Warning light on
OFF: Warning light off
-
Chassis > ABS/VSC/TRC/EPB > Data List
Tester Display
ABS Warning Light
50003 105 51

c.

Check the GTS display condition of the ABS warning light.


Result:
Result Proceed to
ON is displayed. (for LHD) A
ON is displayed. (for RHD) B
OFF is displayed. C



A

B

C