The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.
If any of the following is detected, the brake system warning light (red indicator) remains on:
The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).
The brake fluid level is insufficient.
The vacuum inside the brake booster decreases. (w/ Vacuum Warning Switch)
EBD operation is not possible.
When replacing the skid control ECU (brake actuator assembly), perform system variant learning.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
Inspect the fuses for circuits related to this system before performing the following procedure.
Check if CAN communication system DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check if the skid control ECU (brake actuator assembly) connector is securely connected.
The connector is securely connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the battery voltage.
11 to 14 V
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 8NR-FTS) | B |
| NG (for 3ZR-FAE) | C |
A
B
C
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Disconnect the A42 skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A42-30 (+BS) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Disconnect the A42 skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A42-36 (IG1) - Body ground | Ignition switch ON | 11 to 14 V |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ Stop and Start System) | B |
| NG (w/o Stop and Start System) | C |
A
B
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>Backup Boost Converter Circuit
C
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A42-46 (GND1) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Sub-assembly)) |
Turn the ignition switch off.
Remove the reservoir filler cap and strainer.
Disconnect the A60 brake fluid level warning switch connector.
Measure the resistance according to the value(s) in the table below.
A float is located inside the reservoir. Its position changes according to the brake fluid level.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (+) - 2 (E) | Switch OFF (Float up) | 1.9 to 2.1 kΩ |
| 1 (+) - 2 (E) | Switch ON (Float down) | Below 1 Ω |
If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Disconnect the F4 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F4-12 (SW) - A60-1 (+) | Always | Below 1 Ω |
| F4-12 (SW) or A60-1 (+) - Body ground | Always | 10 kΩ or higher |
| A60-2 (E) - Body ground | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (w/ Vacuum Warning Switch) | A |
| OK (w/o Vacuum Warning Switch) | B |
| NG | C |
A
B
C
Inspect the vacuum warning switch assembly.
Click hereBrake>BRAKE SYSTEM (OTHER)>VACUUM WARNING SWITCH (for LHD)>ON-VEHICLE INSPECTION
The vacuum warning switch assembly is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F5 combination meter connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F5-2 (VCM) - A31-2 (+) | Always | Below 1 Ω |
| F5-2 (VCM) or A31-2 (+) - Body ground | Always | 10 kΩ or higher |
| A31-1 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A41 skid control ECU (brake actuator assembly) connector.
Select the Data List on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Brake Warning Light | Brake system warning light (red indicator) | ON or OFF | ON: Warning light on
OFF: Warning light off |
- |
| Tester Display |
|---|
| Brake Warning Light |
Check the GTS display condition of the brake system warning light (red indicator).
| Result | Proceed to |
|---|---|
| ON is displayed. (for LHD) | A |
| ON is displayed. (for RHD) | B |
| OFF is displayed. | C |
A
B
C
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING