Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › 2016.10–2019.09
RM32H0E _54 Brake _060043 PARKING BRAKE _0294919 ELECTRIC PARKING BRAKE SYSTEM D

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  DTC CHECK / CLEAR  


CHECK DTC AND FREEZE FRAME DATA (USING GTS)


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC/EPB / Trouble Codes.

Chassis > ABS/VSC/TRC/EPB > Trouble Codes
50001 105

f.

Check for DTCs.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

NOTICE:

The electric parking brake system outputs DTCs for the following system. When DTCs other than those in Diagnostic Trouble Code Chart for the electric parking brake system are output, refer to Diagnostic Trouble Code Chart for the relevant system.

System Proceed to
Vehicle Stability Control System (Click here)



g.

Check the freeze frame data.

1.

If DTCs are output, check the freeze frame data and read the vehicle status when the DTC was stored.


HINT:

for Freeze Frame Data: Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>FREEZE FRAME DATA




CLEAR DTC AND FREEZE FRAME DATA (USING GTS)


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC/EPB / Trouble Codes.


f.

Clear the DTCs.

Chassis > ABS/VSC/TRC/EPB > Clear DTCs
50002 105
HINT:

When DTCs are cleared, the freeze frame data will also be cleared.




CHECK DTC (USING SST CHECK WIRE)


a.

Turn the ignition switch off.


b.
C309227C02
1.854,1.5 1.854,1.833 true 1.615,0.813 1.75,0.333 1.75,0.333 1.917,0.333 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *1 1.781,1.896 2.094,2.094 0.313,0.198 10 false TC 1.958,0.271 2.271,0.469 0.313,0.198 10 false CG
*1 DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

NOTICE:

Do not connect the wrong terminals, as this may damage electrical components.



c.

Turn the ignition switch to ON, and read the DTCs from the number of blinks of the parking brake indicator light (red).

HINT:
·

When normal, the light blinks at 0.25 second intervals.

·

If one code is detected:

The light repeats the same code after a pause of 4.5 seconds.

·

If multiple codes are detected:

The light outputs one code after another with a 2.5-second pause between each code.

When all codes have been output, there is a 4.5-second pause and then the light begins to output the codes again.

·

If more than 1 malfunction is detected at the same time, the lowest numbered code will be displayed first.




d.

Check the details of the DTCs.

Warning Light Display GTS Display
19 C13B0
35 C13B4
41 C13A5
42 C13A6
43 C13A7
53 U0100
57 U1103
64 P0805
65 C1207
71 C13AA



CLEAR DTC (USING SST CHECK WIRE)


a.

Turn the ignition switch off.


b.
C309227C02
1.854,1.5 1.854,1.833 true 1.615,0.813 1.75,0.333 1.75,0.333 1.917,0.333 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *1 1.781,1.896 2.094,2.094 0.313,0.198 10 false TC 1.958,0.271 2.271,0.469 0.313,0.198 10 false CG
*1 DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

NOTICE:

Do not connect the wrong terminals, as this may damage electrical components.



c.

Turn the ignition switch to ON.


d.

Within 5 seconds, pull the electric parking brake switch assembly to the lock side 5 times.

NOTICE:

If the electric parking brake switch (electric parking brake switch assembly) is pulled too quickly, the system may not respond. If the system does not respond, perform the operation again more slowly.



e.

Check that a normal system code is output (the parking brake indicator light blinks (red) at 0.25 second intervals).

HINT:

If the malfunction exists, the DTC cannot be cleared.