Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › 2016.10–2019.09
RM32H0E _54 Brake _060043 PARKING BRAKE _0294919 ELECTRIC PARKING BRAKE SYSTEM J

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  Electric Parking Brake does not Operate  


WIRING DIAGRAM

C367783E03
0.427,2.115 1.76,2.458 1.333,0.344 10 false from Engine Stop and Start ECU 0.688,1.354 1.75,1.573 1.063,0.219 10 false ECU-IG1 NO. 2 1.698,1.104 1.906,1.281 0.208,0.177 10 false *1 2.365,1.844 2.635,2.063 0.271,0.219 10 false *2 2.656,1.073 2.854,1.271 0.198,0.198 10 false 36 2.938,1.198 3.281,1.396 0.344,0.198 10 false IG1 2.906,1.865 3.25,2.063 0.344,0.198 10 false A42 2.906,2.073 4.469,2.458 1.563,0.385 10 false Skid Control ECU (Brake Actuator Assembly) 4.281,2.948 6.688,3.208 2.406,0.26 10 false *1: w/o Stop and Start System 4.313,3.344 6.719,3.604 2.406,0.26 10 false *2: w/ Stop and Start System 5.188,1.656 7.01,1.906 1.823,0.25 10 false Combination Meter Assembly 1.281,3.292 3.104,3.542 1.823,0.25 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

The electric parking brake may still operate up to 20 seconds after the ignition switch is turned off. Before disconnecting connectors or fuses, turn the ignition switch off and wait 20 seconds or more.

·

When replacing the skid control ECU (brake actuator assembly), operate the electric parking brake switch assembly as the parking brake indicator light blinks (red) when the ignition switch is first turned to ON.



HINT:

Even if the electric parking brake is operating normally, the parking brake indicator light (red) on the combination meter may be malfunctioning.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

Chassis > Electric Parking Brake > Trouble Codes
50001 184

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.VEHICLE OPERATION CHECK

B

2.VEHICLE OPERATION CHECK
a.

When the vehicle's tires are lifted off the ground and the GTS is used to operate the electric parking brake, check the condition of the rear tires.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>ON-VEHICLE INSPECTION


Result:
Result Proceed to
Lock and release operation is normal and parking brake indicator light turns off or blinks (red) A
Lock and release operation is malfunctioning and parking brake indicator light illuminates (red) or turns off according to switch operation B
Lock and release operation is malfunctioning and parking brake indicator light turns off or blinks (red) C



A

3.PERFORM ACTIVE TEST USING GTS (PARKING BRAKE LIGHT)

B

INSPECT REAR BRAKE

C

5.CHECK HARNESS AND CONNECTOR (BATTERY - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))
3.PERFORM ACTIVE TEST USING GTS (PARKING BRAKE LIGHT)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Electric Parking Brake / Data List.


f.

Read the Data List according to the display on the GTS.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC/EPB > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PKB Light Parking brake indicator light (red) ON or OFF
·

Vehicle stopped

·

Ignition switch ON

·

Parking brake released


Chassis > ABS/VSC/TRC/EPB > Active Test
Tester Display
PKB Light
50004 105 113

g.

Select the Data List on the GTS.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Parking Brake Light Parking brake indicator light (red) output signal OFF, Light or Blink OFF: Parking brake indicator light (red) turns off
Light: Parking brake indicator light (red) illuminates
Blink: Parking brake indicator light (red) flashes
-
Chassis > ABS/VSC/TRC/EPB > Data List
Tester Display
Parking Brake Light
50003 105 479

h.

Check the operating condition of the parking brake indicator light (red) when operating it using the GTS.


Result:
Result Proceed to
Parking brake indicator light (red) in the Data List does not change using the Active Test. A
Parking brake indicator light (red) in the Data List turns ON/OFF using the Active Test. B



A

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

B

4.INSPECT COMBINATION METER ASSEMBLY
4.INSPECT COMBINATION METER ASSEMBLY
a.

Perform the Active Test of the combination meter assembly using the GTS.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. Park
50004 122 69

b.

Check the combination meter assembly.

OK:

Parking brake indicator light (red) turns on or off in accordance with GTS operation.



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

B

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

C

5.CHECK HARNESS AND CONNECTOR (BATTERY - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))
a.

Turn the ignition switch off.


b.
C360727C01
1.5,0.167 2,0.417 0.5,0.25 1.458,1 0.906,1.802 true 0.063,0.042 0.375,0.198 0.313,0.156 10 false *a 1.635,0.198 1.99,0.396 0.354,0.198 10 false A42 0.792,1.823 1.146,2.021 0.354,0.198 10 false IG1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A42-36 (IG1) - Body ground Ignition switch ON 11 to 14 V*1
9.5 to 14 V*2


*1: w/o Stop and Start System

*2: w/ Stop and Start System



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (w/o Stop and Start System) C
NG (w/ Stop and Start System) D



A

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

B

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

D