Home › Brake › PARKING BRAKE › FORCED RELEASE › 2016.10–2018.05
RM32H0E _54 Brake _060043 PARKING BRAKE _0294921 FORCED RELEASE A

PARKING BRAKE  FORCED RELEASE  OPERATION METHOD  


PROCEDURE

Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY (w/ Deck Board)

Hide 64777J 3.REMOVE SPARE WHEEL CUSHION (w/ Deck Board)

Hide 64997 4.REMOVE DECK FLOOR BOX LH (w/ Deck Floor Box)

Hide 64995 5.REMOVE DECK FLOOR BOX RH (w/ Deck Floor Box)

Hide 6. PARKING BRAKE FORCED RELEASE

CAUTION:

Work on a level surface to ensure safety.


NOTICE:
·

To release the parking brake, follow the procedure for when using SST.

·

If the parking brake cannot be released, follow the procedure for when not using SST.

·

When moving the vehicle after releasing the parking brake, install all parts except the connector shown in the illustration.

C366028

·

If the ignition switch ON or the engine is started with the connector disconnected, a DTC may be stored. Clear any DTCs after performing work.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>DTC CHECK / CLEAR



a.

When using SST:

i.

Park the vehicle on a level surface and move the shift lever to P.


ii.

Turn the ignition switch off and chock the wheels.


iii.

Disconnect the connector shown in the illustration.

C366028


iv.

Connect SST (09756-48020) to SST (09756-48070).

SST
09756-48020  09756-48070  

C366029C01
3.115,4.25 4.083,5.417 4.083,5.417 4.25,5.417 true 0.885,1.49 1.219,1.49 true 1.75,1.313 2.083,1.313 true 4.458,7 4.792,7 true 5,8.219 5,7.885 true 2.75,4.792 3.25,5.542 3.25,5.542 3.417,5.542 true 0.5,5.844 0.667,5.844 0.667,5.844 1.833,4.51 true 3.49,5.458 3.802,5.615 0.313,0.156 10 false *1 0.271,5.75 0.583,5.906 0.313,0.156 10 false *2 0.5,0.5 0.813,0.656 0.313,0.156 10 false *a 4.917,8.229 5.146,8.396 0.229,0.167 10 true *b 2.156,1.219 2.469,1.375 0.313,0.156 10 false *c 0.708,1.406 1.021,1.563 0.313,0.156 10 false *d 4.313,5.333 4.802,5.573 0.49,0.24 10 false SST 4.865,6.906 5.115,7.063 0.25,0.156 10 true *a
*1 Brake Pedal Support Assembly *2 Battery
*a SST(09756-48020) *b SST(09756-48070)
*c Release Button *d Finished Light
V100135

Connector - -



v.

Connect SST (09756-48070) to the connector inside of the vehicle.


vi.

Connect SST (09756-48020) to the battery from the outside of the vehicle.


vii.

Push the release button on SST (09756-48020) with the brake pedal depressed.

CAUTION:

The vehicle may suddenly move when the parking brake is released. Make sure to perform the release operation with the brake pedal depressed.


HINT:
·

Confirm that the parking brake is operating by listening for operation sounds.

·

If no operation sounds are heard, push the release button on SST with the brake pedal depressed.

·

The parking brake may not release if the battery voltage is too low. In this case, perform the release operation again using a fully charged or new battery.




viii.

When the FINISHED light of SST (09756-48020) illuminates, release the brake pedal.


ix.

Move the vehicle forward and rearward to check that the parking brake is released.

CAUTION:

Be careful when performing this operation. The vehicle may suddenly move.


NOTICE:
·

When moving the vehicle after releasing the parking brake, check that the connector is disconnected.

·

The brake warning light (yellow) will illuminate when the vehicle is moved after releasing the parking brake.





b.

When not using SST:

NOTICE:

Perform the following procedure only when the parking brake cannot be released using SST.


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



i.

Park the vehicle on a level surface and check that the shift lever is in P.


ii.

Turn the ignition switch off and check that the wheels are chocked.


iii.

Check that the connector shown in the illustration has been disconnected.

C366028


iv.

Remove the rear wheel.

Click hereGeneral>MAINTENANCE>TIRE AND WHEEL>REMOVAL

CAUTION:

When using a jack, do not work on a vehicle supported only by jacks. Make sure to use safety stands.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS



v.
C366000

Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly.


vi.

Remove the parking brake actuator assembly from the rear disc brake cylinder assembly.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>REMOVAL


vii.
C366030

Insert a 6 mm hexagon wrench into the rear disc brake cylinder assembly.


viii.

Turn the 6 mm hexagon wrench 2 turns clockwise to release the parking brake lock.

NOTICE:
·

When moving the vehicle after releasing the parking brake, install all parts except the connector shown in the illustration.

C366028

·

The brake warning light (yellow) will illuminate when the vehicle is moved after releasing the parking brake.





Hide 64997 7.INSTALL DECK FLOOR BOX LH (w/ Deck Floor Box)

Hide 64995 8.INSTALL DECK FLOOR BOX RH (w/ Deck Floor Box)

Hide 64777J 9.INSTALL SPARE WHEEL CUSHION (w/ Deck Board)

Hide 58410B 10.INSTALL DECK BOARD ASSEMBLY (w/ Deck Board)