Home › Engine / Hybrid System › 3ZR-FAE (EMISSION CONTROL) › CANISTER
RM32H0E _51 Engine / Hybrid System _060194 3ZR-FAE EMISSION CONTROL _0295175 CANISTER G

3ZR-FAE EMISSION CONTROL  CANISTER  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT CANISTER (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY) (for Fuel Tank Cap Method)

a.

b.

Check for clogs in the air filter (when not using the GTS).

i.

Start the engine.


ii.

Warm up the engine.


iii.

Allow the engine to idle for 15 minutes.


iv.

Open the fuel tank cap assembly to discharge the pressure in the fuel tank assembly.


v.

Close the fuel tank cap assembly and allow the engine to idle for 30 seconds.


vi.
A202994

Open the fuel tank cap assembly again and check for inhalation sounds.

OK:

No whooshing sounds (inhalation sound) are heard.


HINT:

If there is a smell of gasoline and a whooshing sound (exhalation sound) is heard, positive pressure in the fuel tank assembly is being discharged. This is not a malfunction.




c.

Check for clogs in the air filter (when using the GTS).

i.

Connect the GTS to the DLC3.


ii.

Start the engine.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the EVAP Purge VSV.

Powertrain > Engine and ECT > Active Test
Tester Display
Activate the VSV for Evap Control
50004 234 6

v.

Open the fuel tank cap assembly to discharge the pressure in the fuel tank assembly.


vi.

Perform the Active Test "Activate the EVAP Purge VSV" while the engine is idling.


vii.

Close the fuel tank cap assembly and allow the engine to idle for 30 seconds.


viii.

Open the fuel tank cap assembly and check for inhalation sounds.

OK:

No whooshing sounds (inhalation sound) are heard.


HINT:

If there is a smell of gasoline and a whooshing sound (exhalation sound) is heard, positive pressure in the fuel tank assembly is being discharged. This is not a malfunction.




Hide 2.INSPECT CANISTER (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY) (for Vacuum Measurement Method)

a.

Visually check the canister (fuel suction tube with pump and gauge assembly) for airtightness.

i.

Visually check the canister (fuel suction tube with pump and gauge assembly) for cracks or damage, and check that there is no gasoline smell.



b.

Inspect the airflow of the canister (fuel suction tube with pump and gauge assembly).

NOTICE:

When inspecting with parts installed on the vehicle, be sure to remove the fuel tank cap assembly.


i.
A379116C01
1.406,0.5 1.531,0.5 1.531,0.5 1.656,0.677 false 1.635,1.938 1.76,1.938 1.76,1.938 1.969,1.271 true 1.417,1.854 1.667,2.063 0.25,0.208 10 false *a 1.198,0.427 1.51,0.583 0.313,0.156 10 false *b 2.271,1.979 2.458,2.167 0.188,0.188 10 false *c
*a Port (A)
*b Port (B)
*c Air


Apply compressed air to the port (A) and check that the air flows out from the port (B).

OK:

Air flows out from the port (B).



ii.
A379117C01
2.313,1.365 2.948,1.5 2.948,1.5 2.948,1.646 true 1.552,0.469 1.729,0.469 1.729,0.469 1.844,0.688 false 2.885,1.688 3.115,1.885 0.229,0.198 10 false *a 1.354,0.396 1.635,0.615 0.281,0.219 10 false *b 2.781,0.302 3,0.469 0.219,0.167 10 true *c
*a Port (A)
*b Port (B)
*c Air


Close the port (A) and apply compressed air to the port (B).

OK:

Air does not flow at first. By gradually increasing the pressure, air flows when the pressure in the port reaches a certain level.



iii.
A379118C01
1.719,0.281 2.229,0.281 false 1.573,1.646 1.708,1.646 1.708,1.646 1.833,1.885 false 2.302,2.521 2.938,2.76 2.938,2.76 2.938,2.896 true 2.865,2.917 3.104,3.125 0.24,0.208 10 true *a 1.365,1.563 1.615,1.76 0.25,0.198 10 false *b 2.281,0.188 2.615,0.417 0.333,0.229 10 false *c
*a Port (A)
*b Port (B)
*c Vacuum Pump


Using a vacuum pump, apply vacuum to the port (B) with the port (A) closed.

OK:

The vacuum is maintained at first. By gradually increasing the vacuum, air flows and the vacuum decreases after the vacuum reaches a certain level.




c.
A379109C01
1.396,1.708 1.625,1.708 false 1.667,0.281 1.896,0.281 false 2.344,1.896 2.688,1.052 2.688,1.052 2.865,1.052 true 2.615,1.938 2.823,2.229 2.823,2.229 3,2.229 true 3.063,2.156 3.302,2.354 0.24,0.198 10 true *1 2.917,0.969 3.177,1.188 0.26,0.219 10 false *a 1.188,1.625 1.427,1.833 0.24,0.208 10 false *b 1.948,0.188 2.292,0.396 0.344,0.208 10 false *c
*1 Fuel Hose
*a 3-way Connector
*b Hose
*c Vacuum Pump


Check for clogs in the air filter (when not using the GTS).

i.

Connect the fuel hose to the canister (fuel suction tube with pump and gauge assembly) via the 3-way connector, hose and vacuum pump as shown in the illustration.


ii.

Start the engine.


iii.

Warm up the engine.


iv.

Allow the engine to idle for 15 minutes.


v.

Check the indicator needle of the vacuum pump.

OK:

The indicator needle of the vacuum pump does not rise from its initial position.


HINT:

The indicator needle may shake due to engine vibration, etc., but if it immediately returns to its initial position, there is no problem.




d.
A379109C01
1.396,1.708 1.625,1.708 false 1.667,0.281 1.896,0.281 false 2.344,1.896 2.688,1.052 2.688,1.052 2.865,1.052 true 2.615,1.938 2.823,2.229 2.823,2.229 3,2.229 true 3.063,2.156 3.302,2.354 0.24,0.198 10 true *1 2.917,0.969 3.177,1.188 0.26,0.219 10 false *a 1.188,1.625 1.427,1.833 0.24,0.208 10 false *b 1.948,0.188 2.292,0.396 0.344,0.208 10 false *c
*1 Fuel Hose
*a 3-way Connector
*b Hose
*c Vacuum Pump


Check for clogs in the air filter (when using the GTS).

i.

Connect the fuel hose to the canister (fuel suction tube with pump and gauge assembly) via the 3-way connector, hose and vacuum pump as shown in the illustration.


ii.

Connect the GTS to the DLC3.


iii.

Start the engine.


iv.

Turn the GTS on.


v.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the EVAP Purge VSV.

Powertrain > Engine and ECT > Data List
Tester Display
EVAP Purge VSV
50003 234 217

vi.

Perform the Active Test "Activate the EVAP Purge VSV" while the engine is idling.


vii.

Check the needle of the vacuum pump.

OK:

The needle of the vacuum pump does not rise from its initial position.


HINT:

The indicator needle may shake due to engine vibration, etc., but if it immediately returns to its initial position, there is no problem.