Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › 2016.10–2019.09
RM32H0E _51 Engine / Hybrid System _059427 STOP AND START _0295332 STOP AND START SYSTEM Y

STOP AND START  STOP AND START SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:

*: Use the GTS.


PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
Result:
Proceed to
NEXT



NEXT

3.PRE-CHECK
3.PRE-CHECK
a.

Measure the battery voltage.

Standard voltage:

11 to 14 V (Ignition switch off)


HINT:

If the battery voltage is below 11 V, recharge or replace the battery and initialize* the integrated current value using the GTS*.

·

*: Use the GTS to perform Integrated Current Value Initialization.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

If the Data List item "Integrated Current" is 0 or higher, it is not necessary to perform initialization.




b.

Check the fuses and relays.


c.

Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.


Result:
Proceed to
NEXT



NEXT

4.CHECK DTC AND FREEZE FRAME DATA*
4.CHECK DTC AND FREEZE FRAME DATA*
a.

Check for DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227

b.

Check for freeze frame data.

HINT:

Record or print DTCs and freeze frame data if necessary.



c.

Clear the DTCs and freeze frame data.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Recheck for DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227
HINT:

If any DTCs for the CAN communication system are output, troubleshoot those DTCs first.


Result:
Result Proceed to
DTCs are not output A
DTCs are output B




A

5.PROBLEM SYMPTOMS TABLE

B

5.PROBLEM SYMPTOMS TABLE
a.

Refer to Problem Symptoms Table.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in problem symptoms table A
Fault is listed in problem symptoms table B




A

6.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

7.REPAIR OR REPLACE
6.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

7.REPAIR OR REPLACE
7.REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

8.CONFIRMATION TEST
8.CONFIRMATION TEST
a.

Warm up the engine.


b.

Turn the air conditioning system off.


c.

Drive the vehicle for 5 to 40 minutes.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



d.

Stop the vehicle and confirm that the engine is stopped by stop and start control when all of the following conditions are met:

·

Steering wheel centered

·

Shift lever to neutral and release the clutch pedal.

·

Stop and start indicator light illuminated


HINT:

If the engine is not stopped by stop and start control, air fuel ratio learning and idle speed learning are necessary. Allow the engine to idle for 3 minutes and check that the engine idle speed is within 50 rpm of the target idle speed.



e.

Depress the clutch pedal and check that the engine restarts.


Result:
Proceed to
NEXT



NEXT

END