Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › 2016.10–2019.09
RM32H0E _51 Engine / Hybrid System _059427 STOP AND START _0295332 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

When the engine is started by stop and start control, the engine stop and start ECU controls the starter assembly by activating the ST relay via voltage from terminal STA.

If overcurrent is detected in the starter relay circuit, the engine stop and start ECU stores DTC P0617 and blinks the stop and start cancel indicator light.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P0617 Starter Relay Circuit High Both of the following conditions are met for 1 second (1 trip detection logic):
·

Ignition switch ON

·

Overcurrent to ST relay is detected.


·

Wire harness or connector

·

Engine stop and start ECU


Blinks DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery temperature at 11°C (51°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine and warm it up.


e.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



f.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


g.

Keep the engine stopped by stop and start control for 1 second or more.


h.

Depress the clutch pedal and start the engine.

HINT:

If the engine cranks slowly when the engine is restarted, it can be determined that the battery voltage is low.



i.

Check that DTCs are not output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227


STOP AND START SYSTEM OPERATION CHECK


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery temperature at 11°C (51°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.



a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



d.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


e.

Allow the engine to stop by stop and start control.


f.

Depress the clutch pedal and start the engine.



WIRING DIAGRAM

A392124E01
4.271,8.396 6.094,8.615 1.823,0.219 10 false : CAN Communication Line 6.083,7.521 7.146,7.885 1.063,0.365 10 false Engine Stop and Start ECU 3.177,7.458 4.385,7.667 1.208,0.208 10 false Starter Assembly 0.625,8.01 1.177,8.24 0.552,0.229 10 false Battery 1.396,7.271 1.573,7.469 0.177,0.198 10 false 1 2.115,7.271 2.292,7.469 0.177,0.198 10 false 1 4.031,6.875 4.333,7.052 0.302,0.177 10 false ST 4.406,6.531 4.708,6.708 0.302,0.177 10 false 2 4.396,6.125 4.698,6.302 0.302,0.177 10 false 5 3.729,6.125 4.031,6.302 0.302,0.177 10 false 3 3.719,6.51 3.896,6.708 0.177,0.198 10 false 1 5.813,6.958 6.198,7.146 0.385,0.188 10 false A62 5.885,6.76 6.271,6.948 0.385,0.188 10 false 6 6.188,6.979 6.708,7.156 0.521,0.177 10 false DGND 6.198,4.323 6.719,4.5 0.521,0.177 10 false STA 6.198,2.76 6.719,2.938 0.521,0.177 10 false CLL 6.188,1.833 6.708,2.01 0.521,0.177 10 false CANL 6.177,1.385 6.698,1.563 0.521,0.177 10 false CANH 6.177,0.896 6.698,1.073 0.521,0.177 10 false BIN2 6.188,0.323 6.708,0.5 0.521,0.177 10 false BIN1 5.896,0.104 6.083,0.281 0.188,0.177 10 false 3 5.813,0.313 6.146,0.49 0.333,0.177 10 false A61 5.823,0.885 6.188,1.104 0.365,0.219 10 false A61 5.823,1.385 6.156,1.594 0.333,0.208 10 false F77 5.813,1.833 6.146,2.042 0.333,0.208 10 false F77 5.885,0.698 6.073,0.875 0.188,0.177 10 false 1 5.854,1.188 6.094,1.354 0.24,0.167 10 false 13 5.854,1.656 6.094,1.823 0.24,0.167 10 false 14 3.865,0.458 4.802,0.625 0.938,0.167 10 false BBC NO. 1 3.865,1.021 4.802,1.188 0.938,0.167 10 false BBC NO. 2 1.354,2.333 1.74,2.531 0.385,0.198 10 false STA 1.292,2.76 1.677,2.958 0.385,0.198 10 false NSW 1.25,1.406 1.771,1.583 0.521,0.177 10 false CANH 1.271,1.844 1.792,2.021 0.521,0.177 10 false CANL 1.052,3.188 1.573,3.365 0.521,0.177 10 false A38 1.042,3.344 1.563,3.521 0.521,0.177 10 false ECM 5.813,2.729 6.177,2.948 0.365,0.219 10 false A62 5.813,4.292 6.177,4.51 0.365,0.219 10 false A62 5.865,2.542 6.104,2.76 0.24,0.219 10 false 17 5.844,4.094 6.083,4.313 0.24,0.219 10 false 21 4.958,4.208 5.198,4.427 0.24,0.219 10 false 1 4.115,4.198 4.354,4.417 0.24,0.219 10 false 2 4.021,4.542 4.458,4.719 0.438,0.177 10 false A51 4.01,4.688 5.302,5.063 1.292,0.375 10 false Clutch Start Switch Assembly 3.271,4.198 3.51,4.417 0.24,0.219 10 false 6 2.927,4.198 3.354,4.427 0.427,0.229 10 false ST1 2.229,4.198 2.656,4.427 0.427,0.229 10 false AM1 2.031,4.188 2.24,4.385 0.208,0.198 10 false 5 2.094,4.667 2.531,4.844 0.438,0.177 10 false F12 2.083,4.802 3.625,5.219 1.542,0.417 10 false Ignition or Starter Switch Assembly 1.5,4.448 1.938,4.625 0.438,0.177 10 false AM2 0.615,4.448 1.448,4.615 0.833,0.167 10 false J/B B 1.917,5.969 2.24,6.146 0.323,0.177 10 false ST 0.469,6.406 1.323,6.625 0.854,0.219 10 false BATT-MAIN 1.771,1.219 2.083,1.417 0.313,0.198 10 false 13 1.771,1.677 2.083,1.875 0.313,0.198 10 false 26 1.771,2.219 2.083,2.417 0.313,0.198 10 false 29 1.771,2.615 2.083,2.813 0.313,0.198 10 false 57 1.615,7.26 2.073,7.458 0.458,0.198 10 false C67 2.365,7.26 2.823,7.458 0.458,0.198 10 false C35 2.531,7.5 2.844,7.698 0.313,0.198 10 false ST 4.021,0.156 4.177,0.354 0.156,0.198 10 false 1 4.021,0.729 4.177,0.927 0.156,0.198 10 false 1 4.313,0.156 4.469,0.354 0.156,0.198 10 false 2 4.313,0.719 4.469,0.917 0.156,0.198 10 false 2


CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BBC NO. 1, BBC NO. 2 FUSE)
a.

Disconnect the A61 engine stop and start ECU connector.


b.

Remove the BBC NO. 1 fuse from the No. 1 engine room relay block.


c.

Remove the BBC NO. 2 fuse from the No. 1 engine room relay block.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A61-1 (BIN2) - BBC NO. 2 fuse holder 2 Always Below 1 Ω
A61-3 (BIN1) - BBC NO. 1 fuse holder 2 Always Below 1 Ω
A61-1 (BIN2) - Body ground Always 10 kΩ or higher
A61-3 (BIN1) - Body ground Always 10 kΩ or higher
BBC NO. 1 fuse folder 2 - Body ground Always 10 kΩ or higher
BBC NO. 2 fuse holder 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST RELAY)
a.

Disconnect the A51 clutch start switch assembly.


b.

Disconnect the A38 ECM connector.


c.

Disconnect the A61 and A62 engine stop and start ECU connectors.


d.

Remove the ST relay from the No. 1 engine room relay block.


e.

Remove the BBC NO. 1 fuse from No. 1 engine room relay block.


f.

Remove the BBC NO. 2 fuse from the No. 1 engine room relay block.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A62-21 (STA) - ST relay holder 2 Always Below 1 Ω
A62-21 (STA) - Body ground and other terminals Always 10 kΩ or higher
ST relay holder 2 - Body ground and other terminals Always 10 kΩ or higher
A61-1 (BIN2) - A62-21 (STA) Always 10 kΩ or higher
A61-3 (BIN1) - A62-21 (STA) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE STOP AND START ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ENGINE STOP AND START ECU
a.

Disconnect the A66 engine stop and start ECU connector.

A392127C01
1.083,2.167 1.583,2.417 0.5,0.25 3.167,2.167 3.667,2.417 0.5,0.25 5.417,2.167 5.917,2.417 0.5,0.25 5,0.333 5.5,0.583 0.5,0.25 3.167,0.323 3.667,0.573 0.5,0.25 1.583,0.333 2.083,0.583 0.5,0.25 1.219,2.167 1.677,2.365 0.458,0.198 10 false A61 1.719,0.333 2.177,0.531 0.458,0.198 10 false A61 3.302,0.333 3.76,0.531 0.458,0.198 10 false A62 3.292,2.177 3.75,2.375 0.458,0.198 10 false A62 5.563,2.177 6.021,2.375 0.458,0.198 10 false F77 5.135,0.354 5.594,0.552 0.458,0.198 10 false F77 0.146,0.094 0.604,0.292 0.458,0.198 10 false *a
*a Component without harness connected
(Engine Stop and Start ECU)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A62-21 (STA) - A62-6 (DGND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT ST RELAY

NG

4.INSPECT ST RELAY

Result:
Proceed to
OK
NG



OK

NG

REPLACE ST RELAY