Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › 2016.10–2019.09
RM32H0E _51 Engine / Hybrid System _059427 STOP AND START _0295332 STOP AND START SYSTEM J

STOP AND START  STOP AND START SYSTEM  Stop and Start Cancel Switch Circuit  


DESCRIPTION

Stop and start control can be disabled by pressing the stop and start system cancel switch (electric parking brake switch assembly). The stop and start system cancel switch (electric parking brake switch assembly) is a momentary-type switch that switches between on and off when the switch is pressed. While stop and start control is disabled, the stop and start cancel indicator light is illuminated to inform the driver.

WIRING DIAGRAM

A287084E61
3.406,0.906 4.375,1.146 0.969,0.24 10 false 11 1.927,0.927 2.344,1.156 0.417,0.229 10 false 8 1.646,1.542 2.229,1.823 0.583,0.281 10 false F67 1.646,1.708 4.531,2.115 2.885,0.406 10 false Stop and Start System Cancel Switch (Electric Parking Brake Switch Assembly) 5.333,1.823 5.802,2.021 0.469,0.198 10 false F77 5.333,0.938 5.688,1.24 0.354,0.302 10 false 5 5.604,1.042 6.167,1.313 0.563,0.271 10 false ECAN 5.354,1.99 7.104,2.302 1.75,0.313 10 false Engine Stop and Start ECU 3.167,1.042 3.625,1.24 0.458,0.198 10 false S 2.146,1.042 2.802,1.24 0.656,0.198 10 false E

PROCEDURE

1.READ VALUE USING GTS (CANCEL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / Cancel Switch.


e.

Read the value when the stop and start system cancel switch (electric parking brake switch assembly) is pressed.

Powertrain > Stop and Start > Data List
Tester Display
Cancel Switch
50003 227 17
OK:
Tester Display Condition Normal Condition
Cancel Switch Stop and start system cancel switch (electric parking brake switch assembly) is pressed ON
Stop and start system cancel switch (electric parking brake switch assembly) is not pressed OFF



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT STOP AND START SYSTEM CANCEL SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
2.INSPECT STOP AND START SYSTEM CANCEL SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
a.

Inspect the stop and start system cancel switch (electric parking brake switch assembly).

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM CANCEL SWITCH ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (STOP AND START SYSTEM CANCEL SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY - BODY GROUND))

NG

REPLACE ENGINE STOP AND START SYSTEM CANCEL SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (STOP AND START SYSTEM CANCEL SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY - BODY GROUND))
a.

Disconnect the F67 stop and start system cancel switch (electric parking brake switch assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F67-8 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - STOP AND START SYSTEM CANCEL SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - STOP AND START SYSTEM CANCEL SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))
a.

Disconnect the F77 engine stop and start ECU connector.


b.

Disconnect the F67 stop and start system cancel switch (electric parking brake switch assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-5 (ECAN) - F67-11 (S) Always Below 1 Ω
F77-5 (ECAN) - Body ground and other terminals Always 10 kΩ or higher
F67-11 (S) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR