Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › 2016.10–2019.09
RM32H0E _51 Engine / Hybrid System _059427 STOP AND START _0295332 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  P1780  Discrepancy between Neutral Position SW and Shift Position  


DESCRIPTION

The engine stop and start ECU detects a malfunction by comparing the shift position signal with the neutral position switch signal input state. If a malfunction is detected, the engine stop and start ECU blinks the stop and start cancel indicator light, prohibits the stop and start control and stores DTC P1780.


DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P1780 Discrepancy between Neutral Position SW and Shift Position The following condition continues for 1 second or more (1 trip detection logic)
·

Open or short in neutral position switch circuit.


·

Neutral position switch

·

Engine stop and start ECU

·

ECM

·

Wire harness or connector


Blinking DTC stored

WIRING DIAGRAM

A382306E06
0.979,2.052 1.292,2.25 0.313,0.198 10 false IC 2.333,1.104 2.646,1.302 0.313,0.198 10 false W1 2.25,1.958 2.615,2.156 0.365,0.198 10 false TMN 2.365,2.844 2.677,3.042 0.313,0.198 10 false F+ 0.792,3.469 1.104,3.667 0.313,0.198 10 false C61 0.792,3.625 2.5,3.906 1.708,0.281 10 false Neutral Position Switch 2.677,1.104 2.99,1.302 0.313,0.198 10 false 1 2.688,1.958 3,2.156 0.313,0.198 10 false 2 2.677,2.844 2.99,3.042 0.313,0.198 10 false 3 4.865,1.104 5.177,1.302 0.313,0.198 10 false 26 4.948,1.969 5.26,2.167 0.313,0.198 10 false 8 4.885,2.854 5.198,3.052 0.313,0.198 10 false 25 5.177,1.104 5.802,1.302 0.625,0.198 10 false TMVC 5.177,1.979 5.823,2.219 0.646,0.24 10 false TMN 5.177,2.865 5.615,3.073 0.438,0.208 10 false TME2 5.167,3.771 5.604,3.979 0.438,0.208 10 false A62 5.167,3.927 6.927,4.323 1.76,0.396 10 false Engine Stop and Start ECU 6.125,0.854 6.563,1.063 0.438,0.208 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

When the ECM is replaced on a vehicle with a non-specified battery, it is necessary to perform battery type switching.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA


PROCEDURE

1.READ VALUE USING GTS (NEUTRAL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / Neutral Switch.

Powertrain > Stop and Start > Data List
Tester Display
Neutral Switch
50003 227 9

e.

Read the value when the shift lever is in neutral and any other position

OK:
Tester Display Condition Normal Condition
Neutral Switch Shift lever in neutral ON
Shift lever in any position other than neutral OFF



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - NEUTRAL POSITION SWITCH)
2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - NEUTRAL POSITION SWITCH)
a.

Disconnect the A62 engine stop and start ECU connector.


b.

Disconnect the C61 neutral position switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A62-26 (TMVC) - C61-1 (W1) Always Below 1 Ω
A62-25 (TME2) - C61-3 (F+) Always Below 1 Ω
A62-8 (TMN) - C61-2 (TMN) Always Below 1 Ω
A62-26 (TMVC) - Body ground and other terminals Always 10 kΩ or higher
A62-25 (TME2) - Body ground and other terminals Always 10 kΩ or higher
A62-8 (TMN) - Body ground and other terminals Always 10 kΩ or higher
C61-1 (W1) - Body ground and other terminals Always 10 kΩ or higher
C61-3 (F+) - Body ground and other terminals Always 10 kΩ or higher
C61-2 (TMN) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE STOP AND START ECU (TMN TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ENGINE STOP AND START ECU (TMN TERMINAL VOLTAGE)
a.

Measure the voltage according to the value(s) in the table below.

A387803C09
1.948,0.083 2.448,0.333 0.5,0.25 3.167,0.083 3.667,0.333 0.5,0.25 4.604,0.083 5.104,0.333 0.5,0.25 3.75,1.5 3.073,0.938 true 2.479,1.5 3.063,0.833 true 0.135,0.073 0.448,0.229 0.313,0.156 10 false *a 2.073,0.125 2.531,0.323 0.458,0.198 10 false A61 3.281,0.125 3.74,0.323 0.458,0.198 10 false A62 4.729,0.125 5.188,0.323 0.458,0.198 10 false F77 3.615,1.5 4.229,1.698 0.615,0.198 10 false TME2 2.333,1.5 2.948,1.698 0.615,0.198 10 false TMN
*a Component with harness connected
(Engine Stop and Start ECU)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
A62-8 (TMN) - A62-25 (TME2) Ignition switch ON, shift lever in neutral 2.7 to 4.3 V
Ignition switch ON, shift lever in any position other than neutral 0.7 to 1.9 V



Result:
Result
OK
NG



OK

NG