Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › 2016.10–2019.09
RM32H0E _51 Engine / Hybrid System _059427 STOP AND START _0295332 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  P1540  Brake Booster Sensor Circuit (Open or Short)  


DESCRIPTION

The engine stop and start ECU determines changes in the brake booster assembly pressure based on the voltage signal received from the vacuum sensor assembly in the brake booster assembly.

If the engine stop and start ECU judges that the signal received from the vacuum sensor assembly is abnormal, it stores DTC P1540 and blinks the stop and start cancel indicator light.

A280541E02
0.063,0.052 1.896,0.25 1.833,0.198 10 Vacuum Sensor Voltage: 0.833,0.51 1.688,0.677 0.854,0.167 10 Voltage (V) 0.938,0.781 1.292,1.01 0.354,0.229 10 5.0 0.938,1.188 1.292,1.385 0.354,0.198 10 4.5 0.958,2.49 1.365,2.667 0.406,0.177 10 0.5 1.031,2.896 1.313,3.083 0.281,0.188 10 0 2.667,1.792 3.875,1.99 1.208,0.198 10 Normal Range 2.604,0.875 3.24,1.198 0.635,0.323 10 Abnormal Range 2.604,2.583 3.24,2.906 0.635,0.323 10 Abnormal Range

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P1540 Brake Booster Sensor Circuit (Open or Short) Both of the following conditions are met for 2 seconds or more (1 trip detection logic):
·

Open or short in vacuum sensor assembly circuit

·

Ignition switch is turned to ON


·

Vacuum sensor assembly

·

Engine stop and start ECU

·

Wire harness or connector


Blinks DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared automatically even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery temperature at 11°C (51°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine and allow it to idle for 15 seconds or more.


e.

Stop the engine and turn the ignition switch to ON.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Stop and Start / Data List / Brake Boost Pressure.

Powertrain > Stop and Start > Data List
Tester Display
Brake Boost Pressure
50003 227 61

h.

While depressing the brake pedal several times, check that the Brake Boost Pressure value changes.


i.

Check that DTCs are not output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227


STOP AND START SYSTEM OPERATION CHECK


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery temperature at 11°C (51°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.



a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



d.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


e.

Allow the engine to stop by stop and start control.


f.

Depress the clutch pedal and start the engine.



WIRING DIAGRAM

A387048E03
1.781,0.823 1.938,1.021 0.156,0.198 10 false 3 1.802,1.51 1.958,1.708 0.156,0.198 10 false 2 1.781,2.281 1.938,2.479 0.156,0.198 10 false 1 1.458,0.917 1.781,1.083 0.323,0.167 10 false VC 1.479,1.615 1.802,1.781 0.323,0.167 10 false PB 1.49,2.375 1.813,2.542 0.323,0.167 10 false E2 0.333,2.74 0.74,2.906 0.406,0.167 10 false A50 4.406,0.802 4.729,0.969 0.323,0.167 10 false 14 4.406,1.5 4.729,1.667 0.323,0.167 10 false 13 4.469,2.281 4.792,2.448 0.323,0.167 10 false 3 4.688,0.823 5.26,0.99 0.573,0.167 10 false BRVC 4.677,1.5 5.25,1.667 0.573,0.167 10 false PB 4.656,2.281 5.229,2.448 0.573,0.167 10 false BRE2 5.688,0.563 6.26,0.729 0.573,0.167 10 false 5 V 4.667,3 5.24,3.167 0.573,0.167 10 false A62 4.667,3.167 6.708,3.427 2.042,0.26 10 false Engine Stop and Start ECU 0.323,2.885 2.229,3.104 1.906,0.219 10 false Vacuum Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, perform deceleration sensor zero point clear and calibration.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION



HINT:

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA


PROCEDURE

1.INSPECT VACUUM SENSOR ASSEMBLY

Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - VACUUM SENSOR ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - VACUUM SENSOR ASSEMBLY)
a.

Disconnect the A62 engine stop and start ECU connector.


b.

Disconnect the A50 vacuum sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A62-13 (PB) - A50-2 (PB) Always Below 1 Ω
A62-14 (BRVC) - A50-3 (VC) Always Below 1 Ω
A62-3 (BRE2) - A50-1 (E2) Always Below 1 Ω
A62-13 (PB) - Body ground and other terminals Always 10 kΩ or higher
A62-14 (BRVC) - Body ground and other terminals Always 10 kΩ or higher
A62-3 (BRE2) - Body ground and other terminals Always 10 kΩ or higher
A50-2 (PB) - Body ground and other terminals Always 10 kΩ or higher
A50-3 (VC) - Body ground and other terminals Always 10 kΩ or higher
A50-1 (E2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR