Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)
RM32H0E _56 Audio / Visual / Telematics _060227 AUDIO / VIDEO _0295448 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Radio Broadcast cannot be Received or Poor Reception  


PROCEDURE

1.CHECK RADIO RECEIVER ASSEMBLY
a.

Check the radio automatic station search function.

i.

Check the radio automatic station search function by activating it.

Result:
Result Proceed to
Automatic station search function does not stop A
Automatic station search function stops on a station B





A

2.CHECK OPTIONAL COMPONENTS

B

2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film, are installed.

Result:
Result Proceed to
Optional components are installed A
Optional components are not installed B


NOTICE:

Do not remove optional components without the permission of the customer.




A

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

B

3.CHECK RADIO RECEIVER ASSEMBLY
3.CHECK RADIO RECEIVER ASSEMBLY
a.
E187251

Preparation for check

i.

Disconnect the antenna connector from the radio receiver assembly.



b.

Check for noise

i.

Turn the ignition switch to ACC with the radio receiver assembly connectors connected.


ii.

Turn the radio receiver assembly on and enter AM mode.


iii.

Place a screwdriver, thin wire or other metal object on the radio receiver assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise occurs.




Result:
Result
OK
NG



OK

4.INSPECT RADIO RECEIVER ASSEMBLY

NG

4.INSPECT RADIO RECEIVER ASSEMBLY
a.

Disconnect the RA radio receiver assembly connector.


b.
E188455C32
0.479,0.958 1.01,1.25 0.531,0.292 1.552,1.125 1.146,1.479 true 0.115,0.094 0.292,0.26 0.177,0.167 10 false *a 0.635,1.021 0.854,1.188 0.219,0.167 10 false RA 0.844,1.51 1.24,1.677 0.396,0.167 10 false ANT+
*a Component without harness connected
(Radio Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
RA-5 (ANT+) - Body ground Ignition switch ACC
Radio switch on and FM or AM selected
11 to 14 V



Result:
Proceed to
OK
NG



OK

5.REPLACE ANTENNA CORD SUB-ASSEMBLY

NG

5.REPLACE ANTENNA CORD SUB-ASSEMBLY
a.

Replace the antenna cord sub-assembly and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



OK

END

NG

6.REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY
6.REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.

Replace the No. 2 antenna cord sub-assembly and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



OK

END

NG

7.REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY
7.REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.

Replace the No. 3 antenna cord sub-assembly with a new or known good one and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



OK

END

NG

8.REPLACE ROOF ANTENNA ASSEMBLY
8.REPLACE ROOF ANTENNA ASSEMBLY
a.

Replace the roof antenna assembly and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



OK

END

NG