Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type) › 2016.10–2019.09
RM32H0E _56 Audio / Visual / Telematics _060227 AUDIO / VIDEO _0295448 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  USB Audio System Recognition/Play Error  


DESCRIPTION

When a USB device or "iPod" is connected to the USB connector of the radio receiver assembly or USB jack of the No. 1 stereo jack adapter assembly*1, it must have playable files. The device must also communicate with and be recognized by the radio receiver assembly. This diagnostic procedure is for when a device is not recognized, or files from the device cannot be played normally.

*1: w/ No. 1 stereo jack adapter assembly


WIRING DIAGRAM

E359745E01
1.063,4.323 4.271,4.573 3.208,0.25 10 false : Data Signal (USB Communication Line) 0.438,3.99 3.646,4.24 3.208,0.25 10 false No. 1 Stereo Jack Adapter Assembly 0.448,3.813 0.719,4 0.271,0.188 10 false j1 5.906,4.031 6.885,4.365 0.979,0.333 10 false Radio Receiver Assembly 5.906,3.823 6.177,4.01 0.271,0.188 10 false j3 5.969,3.396 6.521,3.583 0.552,0.188 10 false USG1 5.958,2.823 6.51,3.01 0.552,0.188 10 false UGD1 5.969,2.156 6.521,2.344 0.552,0.188 10 false US1+ 5.958,1.531 6.51,1.719 0.552,0.188 10 false US1- 5.958,0.958 6.51,1.146 0.552,0.188 10 false USV1 0.938,0.948 1.49,1.135 0.552,0.188 10 false UP1 0.875,1.531 1.427,1.719 0.552,0.188 10 false UDO- 0.844,2.125 1.396,2.313 0.552,0.188 10 false UDO+ 0.844,2.802 1.396,2.99 0.552,0.188 10 false UJSG 0.844,3.396 1.396,3.583 0.552,0.188 10 false UJSS 3.281,3.219 4.25,3.427 0.969,0.208 10 false (Shielded) 1.323,0.813 1.594,1 0.271,0.188 10 false 1 5.74,0.844 6.01,1.031 0.271,0.188 10 false 1 1.333,1.375 1.604,1.563 0.271,0.188 10 false 2 5.76,1.375 6.031,1.563 0.271,0.188 10 false 2 5.771,1.99 6.042,2.177 0.271,0.188 10 false 3 1.313,2 1.583,2.188 0.271,0.188 10 false 3 1.313,2.667 1.583,2.854 0.271,0.188 10 false 4 5.771,2.677 6.042,2.865 0.271,0.188 10 false 4 5.76,3.26 6.031,3.448 0.271,0.188 10 false 5 1.323,3.281 1.594,3.469 0.271,0.188 10 false 5 0.125,0.104 3.677,0.344 3.552,0.24 12 false w/ No. 1 Stereo Jack Adapter Assembly:

CAUTION / NOTICE / HINT

HINT:
·

When a large amount of data is in a USB device, it may take a while to begin playback.

·

When using a USB device, files that are copy protection or encrypted due to copyright reasons cannot be played.

·

When files are not played in the sorted order, perform the following procedure before inspection.

(a)

Add numbers in front of the file names.

(b)

Put the files in a folder and copy the folder data to the USB device.




PROCEDURE

1.CHECK USB DEVICE OR "iPod"
a.

Disconnect the USB device or "iPod" from the radio receiver assembly.


b.

Check if playable files are present on the USB device or "iPod".

HINT:

Refer to System Description for playable files.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)>SYSTEM DESCRIPTION



c.

Check if the USB device is a compatible format or "iPod" is a compatible version.

HINT:

Refer to System Description for compatible formats and versions.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)>SYSTEM DESCRIPTION


Result:
Condition Proceed to
No playable files exist, or incompatible device format or version A
Playable files exist, and compatible device format or version (w/o No. 1 stereo jack adapter assembly) B
Playable files exist, and compatible device format or version (w/ No. 1 stereo jack adapter assembly) C




A

END (USB DEVICE FORMAT WAS INCOMPATIBLE, "iPod" VERSION WAS INCOMPATIBLE, OR NO PLAYABLE FILES PRESENT)

B

2.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK

C

5.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
2.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK
a.

Delete all files on the USB device or "iPod" and format/restore it.


b.

Save the data again and check if it can be played on the in-vehicle device.

NOTICE:

Formatting a USB device or restoring an "iPod" erases all music on the device.

Ensure that backup music data is available before performing this operation.


OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END

NG

3.REPLACE USB DEVICE OR RESTORE "iPod"
3.REPLACE USB DEVICE OR RESTORE "iPod"
a.

Turn the ignition switch off.

HINT:

When this malfunction occurs, it is necessary to turn the ignition switch off to make it possible for the vehicle to recognize a new device when it is connected.



b.

Turn the ignition switch to ACC.


c.

Connect a known good USB device or "iPod" to the radio receiver assembly.

HINT:
·

If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.

·

Refer to System Description for compatible formats and versions.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)>SYSTEM DESCRIPTION




Result:
Proceed to
NEXT



NEXT

4.CHECK USB DEVICE OR RESTORE "iPod" AND RECHECK
4.CHECK USB DEVICE OR RESTORE "iPod" AND RECHECK
a.

Check if a USB device or "iPod" is recognized by the radio receiver assembly, and if information such as track, artist and album names is displayed on the screen.

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

USB DEVICE OR "iPod" WAS INCOMPATIBLE OR DEFECTIVE

NG

5.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the j3 radio receiver assembly connector.


b.

Disconnect the j1 No. 1 stereo jack adapter assembly connector.


c.
E359761C02
1.51,2.26 1.896,2.531 0.385,0.271 1.438,0.104 1.823,0.375 0.385,0.271 1.146,1.771 1.583,1.469 true 1.115,1.281 1.573,1.26 true 1.865,1.271 2.323,1.25 true 1.854,1.448 2.271,1.573 true 1.792,1.542 2.229,1.917 true 1.948,3.427 2.542,3.417 true 1.802,3.458 2.5,3.74 true 1.781,3.542 2.438,4.167 true 1.021,3.427 1.49,3.427 true 1.073,3.771 1.604,3.458 true 0.177,0.156 0.49,0.354 0.313,0.198 10 false *a 0.229,2.479 0.542,2.677 0.313,0.198 10 false *b 1.573,0.146 1.885,0.344 0.313,0.198 10 false j3 1.604,2.313 1.917,2.51 0.313,0.198 10 false j1 0.708,1.198 1.323,1.396 0.615,0.198 10 false UGD1 0.781,1.74 1.396,1.938 0.615,0.198 10 false US1+ 2.385,1.188 3,1.385 0.615,0.198 10 false USV1 2.354,1.5 2.969,1.698 0.615,0.198 10 false US1- 2.26,1.885 2.875,2.083 0.615,0.198 10 false USG1 0.719,3.354 1.229,3.563 0.51,0.208 10 false UP1 0.719,3.74 1.229,3.948 0.51,0.208 10 false UDO- 2.594,3.333 3.104,3.542 0.51,0.208 10 false UJSG 2.531,3.677 3.042,3.885 0.51,0.208 10 false UDO+ 2.5,4.146 3.01,4.354 0.51,0.208 10 false UJSS
*a Front view of wire harness connector
(to Radio Receiver Assembly)
*b Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j1-1 (UP1) - j3-1 (USV1) Always Below 1 Ω
j1-2 (UDO-) - j3-2 (US1-) Always Below 1 Ω
j1-3 (UDO+) - j3-3 (US1+) Always Below 1 Ω
j1-4 (UJSG) - j3-4 (UGD1) Always Below 1 Ω
j1-5 (UJSS) - j3-5 (USG1) Always Below 1 Ω
j1-1 (UP1) - Body ground Always 10 kΩ or higher
j1-2 (UDO-) - Body ground Always 10 kΩ or higher
j1-3 (UDO+) - Body ground Always 10 kΩ or higher
j1-4 (UJSG) - Body ground Always 10 kΩ or higher
j1-5 (UJSS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT RADIO RECEIVER ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT RADIO RECEIVER ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)
a.

Reconnect the j3 radio receiver assembly connector.


b.
E226479C67
1.5,0.906 1.979,1.156 0.479,0.25 1.938,2.083 2.531,2.302 true 1.49,2.083 0.844,2.302 true 1.677,0.948 1.979,1.104 0.302,0.156 10 false j1 2.552,2.281 2.979,2.427 0.427,0.146 10 false UJSG 0.563,2.26 0.927,2.458 0.365,0.198 10 false UP1 0.188,0.167 0.385,0.333 0.198,0.167 10 false *a
*a Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
j1-1 (UP1) - j1-4 (UJSG) Ignition switch ACC 5 V



Result:
Proceed to
OK
NG



OK

7.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK

NG

7.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK
a.

Delete all files in the USB device or "iPod" and format/restore it.


b.

Save the data again and check if it can be played on the in-vehicle device.

NOTICE:

Formatting a USB device or restoring an "iPod" erases all music on the device. Ensure that a backup of the music data is available before performing this operation.


OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END

NG

8.REPLACE USB DEVICE OR "iPod"
8.REPLACE USB DEVICE OR "iPod"
a.

Turn the ignition switch off.

HINT:

When this malfunction occurs, it is necessary to turn the ignition switch off to make it possible for the vehicle to recognize a new device when it is connected.



b.

Turn the ignition switch to ACC.


c.

Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.

HINT:
·

If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.

·

Refer to System Description for compatible formats and versions.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)>SYSTEM DESCRIPTION




Result:
Proceed to
NEXT



NEXT

9.CHECK USB DEVICE OR "iPod"
9.CHECK USB DEVICE OR "iPod"
a.

Check if a USB device or "iPod" is recognized by the radio receiver assembly, and if information such as track, artist and album names is displayed on the screen.

OK:

USB device or "iPod" is recognized properly and the information is displayed on the screen.



Result:
Proceed to
OK
NG



OK

USB DEVICE OR "iPod" WAS INCOMPATIBLE OR DEFECTIVE

NG