Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type) › 2016.10–2019.09
RM32H0E _56 Audio / Visual / Telematics _060227 AUDIO / VIDEO _0295448 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Steering Pad Switch Circuit  


DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the radio receiver assembly.

If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.

If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs. Therefore, the radio receiver assembly cannot be operated using the steering pad switch assembly, also the radio receiver assembly itself will not function.

WIRING DIAGRAM

E359929E01
6.177,4.094 6.635,4.292 0.458,0.198 10 false F47 6.177,4.26 7.135,4.74 0.958,0.479 10 false Radio Receiver Assembly 5.531,0.802 5.99,1 0.458,0.198 10 false F29 6.406,0.792 6.865,0.99 0.458,0.198 10 false SW1 4.552,0.792 5.01,0.99 0.458,0.198 10 false z1 4.313,4.125 5.875,4.688 1.563,0.563 10 false Spiral Cable with Sensor Sub-assembly 6.417,1.979 6.875,2.177 0.458,0.198 10 false SWG 6.406,3.594 6.865,3.792 0.458,0.198 10 false SW2 5.521,1.979 5.979,2.177 0.458,0.198 10 false F29 5.531,3.573 5.99,3.771 0.458,0.198 10 false F29 4.542,1.969 5,2.167 0.458,0.198 10 false z1 4.552,3.573 5.01,3.771 0.458,0.198 10 false z1 4.969,0.688 5.427,0.885 0.458,0.198 10 false AU1 4.979,1.885 5.438,2.083 0.458,0.198 10 false EAU 4.99,3.469 5.448,3.667 0.458,0.198 10 false AU2 1.281,5.708 4.156,5.99 2.875,0.281 10 false Steering Pad Switch Assembly 6.177,0.677 6.49,0.875 0.313,0.198 10 false 21 6.188,3.458 6.5,3.656 0.313,0.198 10 false 22 6.188,1.875 6.5,2.073 0.313,0.198 10 false 23 5.563,0.604 5.875,0.802 0.313,0.198 10 false 6 5.552,1.781 5.865,1.979 0.313,0.198 10 false 3 5.583,3.375 5.896,3.573 0.313,0.198 10 false 5 4.521,0.604 4.833,0.802 0.313,0.198 10 false 11 4.552,1.792 4.865,1.99 0.313,0.198 10 false 8 4.531,3.375 4.844,3.573 0.313,0.198 10 false 10 2.667,1.406 3.125,1.604 0.458,0.198 10 false Seek+ 1.927,1.385 2.385,1.583 0.458,0.198 10 false Seek- 1,1.385 1.625,1.604 0.625,0.219 10 false Volume+ 0.26,1.385 0.823,1.688 0.563,0.302 10 false Volume- 1.865,2.969 2.323,3.167 0.458,0.198 10 false MODE 2.583,4.552 3.354,4.813 0.771,0.26 10 false On Hook 1.76,4.563 2.667,4.917 0.906,0.354 10 false Off Hook

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEERING PAD SWITCH SIGNAL)
a.

Disconnect the F47 radio receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F47-21 (SW1) - F47-23 (SWG) No switch pushed 95 to 105 kΩ
Seek+ switch pushed Below 2.5 Ω
Seek- switch pushed 313 to 345 Ω
Volume+ switch pushed 950 to 1050 Ω
Volume- switch pushed 2955 to 3265 Ω
F47-22 (SW2) - F47-23 (SWG) No switch pushed 95 to 105 kΩ
MODE switch pushed Below 2.5 Ω
On hook switch pushed 313 to 345 Ω
Off hook switch pushed 950 to 1050 Ω



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
a.

Remove the spiral cable with sensor sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable with sensor sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION

NOTICE:
·

Press and hold the lock located in the center of the spiral cable with sensor sub-assembly to rotate the spiral cable with sensor sub-assembly.

·

The spiral cable with sensor sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable with sensor sub-assembly may prevent the airbag from deploying.

·

As the spiral cable with sensor sub-assembly may break, do not rotate the spiral cable with sensor sub-assembly more than the specified amount.




Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (RADIO RECEIVER ASSEMBLY - SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - BODY GROUND)

NG

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY