Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)
RM32H0E _56 Audio / Visual / Telematics _060227 AUDIO / VIDEO _0295448 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter  


DESCRIPTION

for Automatic Sound Levelizer (ASL):

This circuit is necessary for the Automatic Sound Levelizer (ASL) built into the radio receiver assembly.

The Automatic Sound Levelizer (ASL) function automatically adjusts the audio system volume level in order to compensate for increased vehicle noise (vehicle noise tends to increase as vehicle speed increases). The ASL adjusts the volume level based upon vehicle speed signals sent from the combination meter assembly.


for "Bluetooth":

Vehicle speed signals are received from the combination meter assembly and used to cancel "Bluetooth" function operation.

The radio receiver assembly recognizes that the vehicle is being driven and makes it impossible to connect or register a "Bluetooth" device while driving.


HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective system based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E361242E02
1.135,1.969 2.104,2.313 0.969,0.344 10 false Radio Receiver Assembly 5.167,1.969 6.344,2.323 1.177,0.354 10 false Combination Meter Assembly 3.76,1.458 5.219,1.646 1.458,0.188 10 false Other ECUs 1.146,1.792 2.365,1.99 1.219,0.198 10 false F47 5.167,1.813 6.385,2.01 1.219,0.198 10 false F4 1.646,1.052 2.865,1.25 1.219,0.198 10 false SPD 5.198,1.063 6.417,1.26 1.219,0.198 10 false +S 2.052,0.917 3.271,1.115 1.219,0.198 10 false 17 4.99,0.938 6.208,1.135 1.219,0.198 10 false 6

PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.

Check the output waveform.

E267543C07
1.667,0.667 2.083,0.917 0.417,0.25 2.271,1.552 2.49,2.135 true 1.76,0.719 2.135,0.917 0.375,0.198 10 false F4 0.229,0.167 0.604,0.365 0.375,0.198 10 false *a 2.458,2.146 2.833,2.344 0.375,0.198 10 false +S 5.115,1.875 5.396,2.094 0.281,0.219 10 false A 6.49,1.646 6.938,1.875 0.448,0.229 10 false GND
*a Component with harness connected
(Combination Meter Assembly)
- -


i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal F4-6 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal F4-6 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.INSPECT RADIO RECEIVER ASSEMBLY (INPUT WAVEFORM)

NG

2.INSPECT RADIO RECEIVER ASSEMBLY (INPUT WAVEFORM)
a.

Check the output waveform.

E265791C36
1.646,0.271 2.063,0.531 0.417,0.26 2.604,1.844 2.406,1.406 true 0.177,0.146 0.49,0.344 0.313,0.198 10 false *a 1.708,0.313 2.094,0.521 0.385,0.208 10 false F47 2.5,1.854 2.813,2.052 0.313,0.198 10 false SPD 4.781,1.708 5.094,1.906 0.313,0.198 10 false A 6.167,1.469 6.594,1.688 0.427,0.219 10 false GND
*a Component with harness connected
(Radio Receiver Assembly)
- -


i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal F47-17 (SPD) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal F47-17 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the F47 radio receiver assembly connector.


b.

Disconnect the F4 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F47-17 (SPD) - F4-6 (+S) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR