Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › REAR DRIVE SHAFT ASSEMBLY (for TMC Made)
RM32H0E _52 Drivetrain _060137 DRIVE SHAFT / PROPELLER SHAFT _0295582 REAR DRIVE SHAFT ASSEMBLY(for TMC Made) A

DRIVE SHAFT / PROPELLER SHAFT  REAR DRIVE SHAFT ASSEMBLY(for TMC Made)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 41336K 1.INSTALL REAR DRIVE SHAFT DUST COVER LH

C129497N01
0.917,1.313 0.75,1 0.75,1 0.583,1 true 0.25,0.917 0.563,1.083 0.313,0.167 10 SST

a.

Using SST and a press, install a new rear drive shaft dust cover LH.

SST
09527-10011  

NOTICE:
·

The rear drive shaft dust cover LH should be installed completely.

·

Be careful not to damage the rear drive shaft dust cover LH.

·

Install the rear drive shaft dust cover LH in the correct direction.




Hide 2.INSTALL REAR DRIVE SHAFT OUTBOARD JOINT BOOT LH

C166359C21
1.917,0.885 2.427,0.375 2.427,0.375 2.792,0.375 false 2.823,0.281 3.177,0.49 0.354,0.208 10 *a
*a Protective Tape


a.

Wrap the splines of the rear drive shaft outboard joint shaft assembly with protective tape to prevent the boot from being damaged.


b.
C274280C06
1.115,1.719 1.115,1.427 false 1.656,1.74 1.656,1.479 false 2.344,1.74 2.344,1.438 false 2.979,1.75 2.979,1.229 false 1.063,1.781 1.375,1.938 0.313,0.156 10 *1 1.604,1.792 1.917,1.948 0.313,0.156 10 *2 2.281,1.781 2.594,1.938 0.313,0.156 10 *3 2.948,1.792 3.26,1.948 0.313,0.156 10 *4
*1 Rear Drive Shaft Outboard Joint Shaft Assembly
*2 Rear No. 2 Drive Shaft Outboard Joint Boot Clamp LH
*3 Rear Drive Shaft Outboard Joint Boot LH
*4 Rear Drive Shaft Outboard Joint Boot Clamp LH
V100135

Outboard joint side
V100136

Inboard joint side


Install new parts to the rear drive shaft outboard joint shaft assembly in the following order:

i.

Rear No. 2 drive shaft outboard joint boot clamp LH


ii.

Rear drive shaft outboard joint boot LH


iii.

Rear drive shaft outboard joint boot clamp LH



c.

Pack the joint portion of the rear drive shaft outboard joint shaft assembly and outboard joint boot with grease.

Standard Grease Capacity:

37 to 47 g (1.31 to 1.65 oz.)



d.

Install the rear drive shaft outboard joint boot to the rear drive shaft outboard joint shaft assembly groove.

NOTICE:
·

Do not allow grease to adhere to the boot clamp track of the rear drive shaft outboard joint boot LH.

·

Keep the inside of the rear drive shaft outboard joint boot LH free of foreign matter.




Hide 42346F 3.INSTALL REAR NO. 2 DRIVE SHAFT OUTBOARD JOINT BOOT CLAMP LH

CAUTION:
·
C331975

When installing the rear No. 2 drive shaft outboard joint boot clamp LH, do not perform the work without wearing protective gloves.

·

If work is performed without using protective gloves, injuries may occur.



a.
C277141

Using a screwdriver, install the rear No. 2 drive shaft outboard joint boot clamp LH as shown in the illustration.

NOTICE:

Be careful not to damage the rear drive shaft outboard joint boot LH.



Hide 42346D 4.INSTALL REAR DRIVE SHAFT OUTBOARD JOINT BOOT CLAMP LH

a.

Install the rear drive shaft outboard joint boot clamp LH onto the rear drive shaft outboard joint boot LH.


b.
C277142C01
1.146,1.615 1.354,1.615 1.354,1.615 1.75,0.99 true 2.271,1.719 2.583,1.917 0.313,0.198 10 *a 2.188,0.083 2.5,0.281 0.313,0.198 10 *b 0.823,1.521 1.135,1.719 0.313,0.198 10 SST
*a Turn
*b Hold


Place SST onto the rear drive shaft outboard joint boot clamp LH.

SST
09521-24010  


c.

Tighten SST so that the rear drive shaft outboard joint boot clamp LH is pinched.

NOTICE:
·

Do not overtighten SST.

·

Be careful not to damage the rear drive shaft outboard joint boot LH.




d.
C277143N01
1.75,1.375 2.177,1.865 2.177,1.865 2.365,1.865 true 2.417,1.75 2.875,1.948 0.458,0.198 10 SST

Using SST, measure the clearance of the rear drive shaft outboard joint boot clamp LH.

SST
09240-00020  

Clearance:

1.2 mm (0.0472 in.) or less


NOTICE:

If the measured value exceeds the specified value, retighten the rear drive shaft outboard joint boot clamp LH.



Hide 5.INSTALL REAR DRIVE SHAFT INBOARD JOINT ASSEMBLY LH

a.

Wrap the spline of the rear drive shaft outboard joint shaft assembly with protective tape to prevent the boot from being damaged.


b.
C274277C07
0.688,1.875 0.688,1.333 false 1.698,1.854 1.698,1.615 false 2.49,1.875 2.49,1.667 false 2.927,1.885 2.927,1.25 false 0.625,1.896 0.938,2.052 0.313,0.156 10 *1 1.635,1.896 1.948,2.052 0.313,0.156 10 *2 2.417,1.906 2.729,2.063 0.313,0.156 10 *3 2.875,1.896 3.188,2.052 0.313,0.156 10 *a
*1 Rear Drive Shaft Inboard Joint Boot Clamp LH
*2 Rear Drive Shaft Inboard Joint Boot LH
*3 Rear No. 2 Drive Shaft Inboard Joint Boot Clamp LH
*a Protective Tape
V100135

Outboard joint side
V100136

Inboard joint side


Install new parts to the rear drive shaft outboard joint shaft assembly in the following order:

i.

Rear drive shaft inboard joint boot clamp LH


ii.

Rear drive shaft inboard joint boot LH


iii.

Rear No. 2 drive shaft inboard joint boot clamp LH



c.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



d.

Remove the protective tape.


e.
C127694C08
1.927,1.188 2.083,1.833 2.083,1.833 1.365,1.531 true 2.083,1.833 2.25,1.833 false 2.313,1.729 3.042,1.896 0.729,0.167 10 *a
*a Matchmark


Align the matchmarks and install the tripod joint to the rear drive outboard joint shaft assembly.

NOTICE:

Face the serrated side of the tripod joint outward and install it to the outboard joint end.



f.

Using a brass bar and a hammer, install the tripod joint to the rear drive outboard joint shaft assembly.

NOTICE:
·

Do not tap the rollers.

·

Keep the tripod joint free of foreign matter.

·

Make sure to install the tripod joint in the correct direction.




g.
F045046

Using a snap ring expander, install a new rear drive shaft snap ring LH to the rear drive outboard joint shaft assembly.


h.

Pack the rear drive inboard joint assembly and rear axle inboard boot LH with grease.

Standard grease capacity:

77 to 87 g (2.72 to 3.06 oz.)



i.
C160821C18
1.823,0.781 0.792,0.458 0.792,0.458 1.375,1.229 false 0.594,0.375 0.854,0.542 0.26,0.167 10 *a
*a Matchmark


Align the matchmarks and install the rear drive shaft inboard joint assembly LH to the rear drive shaft outboard joint shaft assembly.


Hide 6.INSTALL REAR DRIVE SHAFT INBOARD JOINT BOOT LH

a.

Install the rear drive shaft inboard joint boot LH to the rear drive shaft inboard joint assembly LH.


b.
C127699N10
1.438,1.521 1.656,1.74 0.219,0.219 10 (A)

Check whether the drive shaft dimensions are within the following specifications.

HINT:

The following table shows the dimension (A) of the drive shaft.


Dimension (A):
LH Side RH Side
742.2 mm (2.44 ft.) 728.7 mm (2.39 ft.)



Hide 42347E 7.INSTALL REAR NO. 2 DRIVE SHAFT INBOARD JOINT BOOT CLAMP LH

a.
C129501

Using needle-nose pliers, install the rear No. 2 drive shaft inboard joint boot clamp LH as shown in the illustration.

NOTICE:

Be careful not to damage the rear drive shaft inboard joint boot LH.



Hide 42347D 8.INSTALL REAR DRIVE SHAFT INBOARD JOINT BOOT CLAMP LH

a.

Perform the same procedure as for the rear No. 2 drive shaft inboard joint boot clamp LH.