Home › Drivetrain › EC6A (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE UNIT › 2016.10–2020.08
RM32H0E _52 Drivetrain _059609 EC6A MANUAL TRANSMISSION / TRANSAXLE _0295676 MANUAL TRANSAXLE UNIT A

EC6A MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE UNIT  REASSEMBLY  


PROCEDURE

Hide 41311E 1.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C193768N04
0.781,2.688 0.438,2.688 0.438,2.688 0.729,3.104 false 2.177,0.958 1.896,0.958 1.896,0.958 2.104,1.365 false 0.094,2.594 0.438,2.771 0.344,0.177 10 SST 1.542,0.865 1.885,1.042 0.344,0.177 10 SST

Using SST and a press, install a new front differential case front tapered roller bearing (inner race) to the differential case assembly.

SST
09309-37010  
09506-35010  


b.
C194658N10
0.927,1.396 0.49,1.396 0.49,1.396 0.833,2.594 true 2.385,0.313 2.229,0.313 2.229,0.313 2.323,0.531 false 0.146,1.302 0.667,1.625 0.521,0.323 10 false SST 1.927,0.24 2.448,0.563 0.521,0.323 10 false SST

Using SST and a press, install a new front differential case front tapered roller bearing (outer race) together with the front differential case front plate washer to the front transaxle case.

SST
09950-60020  (09951-00680)
09950-70010  (09951-07200)


Hide 41311F 2.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
C193769N04
1.094,2.917 0.698,2.917 0.698,2.917 1.042,3.208 false 2.052,0.573 1.646,0.573 1.646,0.573 1.958,0.854 false 0.354,2.823 0.719,3.063 0.365,0.24 10 SST 1.302,0.49 1.667,0.729 0.365,0.24 10 SST

Using SST and a press, install a new front differential case rear tapered roller bearing (inner race) to the differential case assembly.

SST
09636-20010  
09726-40010  


b.
C194656N14
1.583,1.24 1.24,1.24 1.24,1.24 1.396,1.885 false 3.167,1.271 3.167,1.115 3.167,1.115 3.042,1.115 false 2.448,0.24 2.229,0.24 2.229,0.24 2.323,0.396 false 1.833,2.563 2.594,2.563 false 0.958,1.135 1.375,1.365 0.417,0.229 10 false SST 2.667,2.479 3.083,2.708 0.417,0.229 10 false SST 3.01,1.292 3.427,1.521 0.417,0.229 10 false SST 1.917,0.188 2.333,0.417 0.417,0.229 10 false SST

Using SST and a press, install a new front differential case rear tapered roller bearing (outer race) together with the front differential case rear plate washer to the manual transmission case.

SST
09309-36010  
09950-60020  (09951-00730)
09950-70010  (09951-07100)

HINT:

Use a front differential case rear plate washer of the same thickness as the removed one.



Hide 3.ADJUST DIFFERENTIAL SIDE BEARING PRELOAD

a.

Remove any remaining seal packing from the contact surfaces of the front transaxle case and manual transmission case.


b.
C194633

Coat the differential case assembly with gear oil and install it to the front transaxle case.


c.
C194620

Install the manual transmission case to the front transaxle case with the 16 bolts.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


d.
C327422C01
0.365,0.625 0.49,0.625 0.49,0.625 0.74,0.865 true 0.25,1.375 0.25,1.167 0.25,1.167 0.854,1.167 true 0.188,0.542 0.448,0.75 0.26,0.208 10 false *1 0.135,1.396 0.427,1.583 0.292,0.188 10 true SST
*1 Front Differential Case Rear Plate Washer


Using SST and a torque wrench, turn the differential case assembly clockwise and counterclockwise 2 or 3 times to allow the bearings to settle.

SST
09564-32011  


e.

Using SST and a torque wrench, measure the preload.

SST
09564-32011  

Preload (at Starting):
New Bearing:

1.0 to 1.6 N*m (10 to 16 kgf*cm, 9 to 14 in.*lbf)

Used Bearing:

0.8 to 1.3 N*m (8 to 13 kgf*cm, 7 to 12 in.*lbf)


If the preload is not as specified, replace the front differential case rear plate washer with one of a different thickness. Use the table below to select a front differential case rear plate washer which will ensure that the preload is within the specification.

Front Differential Case Rear Plate Washer Thickness:
Mark Thickness mm (in.) Mark Thickness mm (in.)
10 2.100 (0.0827) 26 2.500 (0.0984)
11 2.125 (0.0837) 27 2.525 (0.0994)
12 2.150 (0.0846) 28 2.550 (0.100)
13 2.175 (0.0856) 29 2.575 (0.101)
14 2.200 (0.0866) 30 2.600 (0.102)
15 2.225 (0.0876) 31 2.625 (0.103)
16 2.250 (0.0886) 32 2.650 (0.104)
17 2.275 (0.0896) 33 2.675 (0.105)
18 2.300 (0.0906) 34 2.700 (0.106)
19 2.325 (0.0915) 35 2.725 (0.107)
20 2.350 (0.0925) 36 2.750 (0.108)
21 2.375 (0.0935) 37 2.775 (0.109)
22 2.400 (0.0945) 38 2.800 (0.110)
23 2.425 (0.0955) 39 2.825 (0.111)
24 2.450 (0.0965) 40 2.850 (0.112)
25 2.475 (0.0974) - -


HINT:
·

Select a thicker front differential case rear plate washer to increase the preload or a thinner front differential case rear plate washer to decrease the preload.

·

Make a memo as the torque values will be needed to adjust output shaft bearing preload.




f.

Remove the 16 bolts and manual transmission case from the front transaxle case.


g.

Remove the differential case assembly from the front transaxle case.


Hide 33321N 4.INSTALL FRONT OUTPUT SHAFT BEARING (OUTER RACE)

a.
C194638C06
1.188,0.708 1.458,0.708 true 0.99,0.604 1.177,0.781 0.188,0.177 10 true *a
*a Key


Install the output shaft cover to the front transaxle case.

NOTICE:

Insert the key of the output shaft cover into the front transaxle case groove.



b.
C194659N07
1.5,1.281 1.219,1.281 1.219,1.281 1.427,1.729 true 2.49,0.323 2.333,0.323 2.333,0.323 2.427,0.531 false 0.875,1.208 1.333,1.49 0.458,0.281 10 false SST 2.031,0.24 2.49,0.521 0.458,0.281 10 false SST

Using SST and a press, install a new front output shaft bearing (outer race) to the front transaxle case.

SST
09950-60010  (09951-00630)
09950-70010  


Hide 33321A 5.INSTALL REAR OUTPUT SHAFT BEARING (OUTER RACE)

a.
C194657N10
2.417,2.552 2.271,2.208 2.271,2.208 2.5,2.208 false 1.354,1.188 2.823,1.188 2.823,1.188 1.438,1.563 true 2,2.135 2.542,2.406 0.542,0.271 10 false SST 2.906,1.115 3.281,1.354 0.375,0.24 10 false SST

Using SST and a press, install a new rear output shaft bearing (outer race) together with the rear output shaft bearing shim to the manual transmission case.

SST
09950-60010  (09951-00590)
09950-70010  (09951-07200)

HINT:

Use a rear output shaft bearing shim of the same thickness as the removed one.



Hide 6.ADJUST OUTPUT SHAFT BEARING PRELOAD

a.

Remove any remaining seal packing from the contact surfaces of the front transaxle case and manual transmission case.


b.
C194633

Coat the differential case assembly with gear oil and install it to the front transaxle case.


c.
A295613

Coat the output shaft assembly with gear oil and install it to the front transaxle case.


d.
C194620

Install the manual transmission case to the front transaxle case with the 16 bolts.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


e.
C327423C01
0.781,0.219 1.469,0.219 true 0.5,1.365 0.615,1.365 0.615,1.365 0.875,1.885 true 0.583,0.125 0.927,0.396 0.344,0.271 10 false *1 0.188,1.271 0.542,1.521 0.354,0.25 10 false SST
*1 Rear Output Shaft Bearing Shim


Using SST and a torque wrench, turn the differential case assembly clockwise and counterclockwise 2 or 3 times to allow the bearings to settle.

SST
09564-32011  


f.

Using SST and a torque wrench, measure the preload. Calculate the rear output shaft bearing preload using the following formula.

SST
09564-32011  

Formula:

Measured preload - Differential side bearing preload = Output shaft bearing preload


Bearing Preload (at starting)
New bearing 4.6 to 7.9 N*m (47 to 81 kgf*cm, 41 to 70 in.*lbf)
Used bearing 3.0 to 5.1 N*m (31 to 52 kgf*cm, 27 to 45 in.*lbf)

If the preload is not as specified, replace the rear output shaft bearing shim with one of a different thickness. Use the table below to select a rear output shaft bearing shim which will ensure that the preload is within the specification.

Rear Output Shaft Bearing Shim Thickness:
Mark Thickness mm (in.) Mark Thickness mm (in.)
50 1.750 (0.0689) 72 2.300 (0.0906)
51 1.775 (0.0699) 73 2.325 (0.0915)
52 1.800 (0.0709) 74 2.350 (0.0925)
53 1.825 (0.0719) 75 2.375 (0.0935)
54 1.850 (0.0728) 76 2.400 (0.0945)
55 1.875 (0.0738) 77 2.425 (0.0955)
56 1.900 (0.0748) 78 2.450 (0.0965)
57 1.925 (0.0758) 79 2.475 (0.0974)
58 1.950 (0.0768) 80 2.500 (0.0984)
59 1.975 (0.0778) 81 2.525 (0.0994)
60 2.000 (0.0787) 82 2.550 (0.100)
61 2.025 (0.0797) 83 2.575 (0.101)
62 2.050 (0.0807) 84 2.600 (0.102)
63 2.075 (0.0817) 85 2.625 (0.103)
64 2.100 (0.0827) 86 2.650 (0.104)
65 2.125 (0.0837) 87 2.675 (0.105)
66 2.150 (0.0846) 88 2.700 (0.106)
67 2.175 (0.0856) 89 2.725 (0.107)
68 2.200 (0.0866) 90 2.750 (0.108)
69 2.225 (0.0876) 91 2.775 (0.109)
70 2.250 (0.0886) 92 2.800 (0.110)
71 2.275 (0.0896) - -


HINT:

Select a thicker rear output shaft bearing shim to increase the preload or a thinner rear output shaft bearing shim to decrease the preload.



g.

Remove the 16 bolts and manual transmission case from the front transaxle case.


h.

Remove the output shaft assembly from the front transaxle case.


i.

Remove the differential case assembly from the front transaxle case.


Hide 33253H 7.INSTALL OUTER SHIFT LEVER OIL SEAL

a.
C194654C05
1.833,2.052 1.833,2.906 1.833,2.906 2.021,2.177 true 1.708,2.948 2.063,3.156 0.354,0.208 10 false SST 0.75,1.49 0.958,1.708 0.208,0.219 10 false *a
*a Depth


Using SST and a hammer, install a new outer shift lever oil seal to the manual transmission case.

SST
09950-60010  (09951-00260)
09950-70010  (09951-07100)

Standard Depth:

0.5 to 1.0 mm (0.0197 to 0.0394 in.)



b.

Coat the lip of the outer shift lever oil seal with MP grease.


Hide 33253 8.INSTALL OUTER NO. 1 SHIFT LEVER

a.
C194649C03
0.479,3.031 0.656,3.156 0.656,3.156 0.844,3.156 true 0.75,2.323 1.188,2.531 0.438,0.208 10 false *b 0.896,3.083 1.302,3.24 0.406,0.156 10 false *a
*a Mark
*b Depth


Install the inner No. 1 shift lever, outer shift lever spacer and outer No. 1 shift lever to the manual transmission case.

HINT:

Install the inner No. 1 shift lever with its mark facing the outside of the manual transmission case.



b.

Using a 5 mm pin punch and a hammer, install the inner shift lever slotted spring pin to the inner No. 1 shift lever.

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)



Hide 33109C 9.INSTALL MANUAL TRANSMISSION OIL SEPARATOR SUB-ASSEMBLY

a.
C194648

Install the manual transmission oil separator sub-assembly to the manual transmission case with the 4 bolts.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)

HINT:

Make sure that the end tabs of the manual transmission oil separator sub-assembly are inserted into the grooves of the manual transmission case.



Hide 33176B 10.INSTALL TRANSMISSION OIL SEPARATOR

a.
C194647

Install the transmission oil separator to the manual transmission case with the 2 bolts.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)

HINT:

Make sure that the tip of the transmission oil separator is inserted into the groove of the manual transmission case.



Hide 33124C 11.INSTALL NO. 1 OIL RECEIVER PIPE

a.
C368152

Install the No. 1 oil receiver pipe to the manual transmission case.

HINT:

Make sure that the No. 1 oil receiver pipe fully contacts the manual transmission case.



Hide 12.INSTALL STRAIGHT PIN

a.
C294819C01
0.656,4.198 0.969,4.396 0.313,0.198 10 false *a
*a Protrusion Height


Using a plastic hammer, install 5 new straight pins to the front transaxle case to the specified protrusion height.

Protrusion Height:

8.5 to 9.5 mm (0.335 to 0.374 in.)



Hide 13.INSTALL REVERSE RESTRICT PIN ASSEMBLY

a.
C195992

Install the reverse restrict pin assembly to the front transaxle case.


Hide 33101J 14.INSTALL BREATHER PLUG

a.
C194732N10
1.167,2.156 1.167,2.896 1.167,2.896 1.042,2.896 true 2.375,0.49 2.375,0.24 2.375,0.24 2.167,0.24 false 0.74,2.833 1.094,3.063 0.354,0.229 10 false SST 1.896,0.167 2.25,0.396 0.354,0.229 10 false SST

Using SST and a hammer, install the breather plug to the front transaxle case.

SST
09350-30020  (09350-07110)


Hide 33176B 15.INSTALL TRANSMISSION OIL SEPARATOR

a.
C194635

Install the transmission oil separator to the front transaxle case with the 4 bolts.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


Hide 31105D 16.INSTALL FRONT TRANSAXLE CASE OIL SEAL

a.
C194660C09
1.479,2.063 0.677,3.208 0.677,3.208 1.458,2.51 false 2.25,0.615 2.094,0.583 2.094,0.583 2.177,0.938 false 0.375,3.125 0.698,3.313 0.323,0.188 10 false SST 1.792,0.479 2.115,0.667 0.323,0.188 10 false SST 3.01,1.323 3.323,1.656 0.313,0.333 10 false *a
*a Depth


Using SST and a hammer, install a new front transaxle case oil seal to the front transaxle case.

SST
09950-60010  (09951-00350)
09950-70010  (09951-07100)

Standard Depth:

0.9 to 1.9 mm (0.0354 to 0.0748 in.)



b.

Coat the lip of the front transaxle case oil seal with MP grease.


Hide 33449B 17.INSTALL TRANSMISSION MAGNET

a.
C194634

Clean the transmission magnet and install it to the front transaxle case.


Hide 33137 18.INSTALL INPUT SHAFT COVER

a.
A295612C03
1.052,1.875 1.229,1.875 1.229,1.875 1.354,2.052 true 0.865,1.781 1.052,1.969 0.188,0.188 10 true *a
*a Key


Install the input shaft cover to the manual transmission case.

NOTICE:

Insert the key of the input shaft cover into the manual transmission case groove.



Hide 33311K 19.INSTALL REAR INPUT SHAFT BEARING SHIM

a.
C194644

Install the rear input shaft bearing shim to the manual transmission case.

NOTICE:

The rear input shaft bearing shim should be cleaned before assembly.



b.

Measure the distance between the end of the manual transmission case and rear input shaft bearing shim (Dimension (A)).

C276973C03
1.104,1.188 0.948,0.958 0.948,0.958 0.792,0.958 false 3.99,2.063 3.604,2.063 false 4.948,2.073 4.729,2.073 4.729,2.073 4.729,1.396 false 0.625,0.896 0.938,1.052 0.313,0.156 10 false *1 4.052,1.979 4.365,2.135 0.313,0.156 10 false *2 5.052,2.01 5.365,2.167 0.313,0.156 10 false *3 2.542,1.427 2.854,1.583 0.313,0.156 10 false *a 6.969,1.135 7.135,1.354 0.167,0.219 10 false *b 4.375,1.094 4.688,1.25 0.313,0.156 10 false *c
*1 Manual Transmission Case *2 Input Shaft Assembly
*3 Front Transaxle Case - -
*a Dimension (A) *b Dimension (B)
*c Dimension (C) - -



c.

Measure the distance between the end of the front transaxle case and installation surface of the front input shaft bearing (Dimension (B)).


d.

Measure the distance between both input shaft bearing outer races (Dimension (C)).

NOTICE:

Measure Dimension (C) with each bearing having no axial clearance.



e.

Calculate the rear input shaft bearing shim value using the following formula.

Formula:

(Dimension (A) + Dimension (B)) - Dimension (C) - Rear input shaft bearing shim thickness = 0.02 mm (0.000787 in.) to 0.14 mm (0.00551 in.)


If the preload is not as specified, replace the rear input shaft bearing shim with one of a different thickness. Use the table below to select a rear input shaft bearing shim which will ensure that the preload is within the specification.

Rear Input Shaft Bearing Shim Thickness:
Mark Thickness mm (in.) Mark Thickness mm (in.)
08 1.30 (0.0512) 14 1.60 (0.0630)
09 1.35 (0.0531) 15 1.65 (0.0650)
10 1.40 (0.0551) 16 1.70 (0.0669)
11 1.45 (0.0571) 17 1.75 (0.0689)
12 1.50 (0.0591) 18 1.80 (0.0709)
13 1.55 (0.0610) 19 1.85 (0.0728)



f.

Coat the rear input shaft bearing shim with MP grease and install it to the manual transmission case.

NOTICE:

Do not apply MP grease to the oil grooves.



Hide 20.INSTALL DIFFERENTIAL CASE ASSEMBLY

a.
C194633

Coat the differential case assembly with gear oil and install it to the front transaxle case.


Hide 21.INSTALL NO. 3 REVERSE PRE-BALK HEAD

a.

Secure the No. 3 gear shift fork assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C325115

Install the No. 3 reverse pre-balk head to the No. 3 gear shift fork assembly.


c.
C325116C01
2.042,0.094 2.26,0.344 0.219,0.25 10 false *a
*a Depth


Using a 5 mm pin punch and a hammer, install the slotted spring pin to the No. 3 reverse pre-balk head.

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)



Hide 22.INSTALL NO. 3 GEAR SHIFT HEAD

a.
C325112

Install the No. 3 gear shift head to the No. 3 gear shift fork assembly.


b.
C325113C01
2.177,0.073 2.479,0.281 0.302,0.208 10 false *a 2.406,0.188 2.708,0.396 0.302,0.208 10 false *a
*a Height


Using a 5 mm pin punch and a hammer, install the slotted spring pin to the No. 3 gear shift head.

Standard Height:

1.0 mm (0.0394 in.) or less



Hide 23.INSTALL SHIFT LEVER STOPPER

a.
C325127

Install the shift lever stopper to the No. 2 gear shift fork assembly as shown in the illustration.


b.
C325128C01
1.719,0.521 2.031,0.76 0.313,0.24 10 false *a
*a Depth


Using a 5 mm pin punch and a hammer, install the slotted spring pin to the shift lever stopper.

Standard Depth:

-0.1 to 0.9 mm (-0.00394 to 0.0354 in.)



c.
C325125

Install the torsion spring to the No. 2 gear shift fork assembly.


Hide 24.INSTALL NO. 2 REVERSE PRE-BALK HEAD

a.
C325129C01
1.25,1.927 0.729,2.292 0.729,2.292 1.25,1.729 true 1.292,4.292 0.948,4.448 0.948,4.448 1.292,4.094 true 2.104,1.708 2.188,1.708 2.188,1.708 2.292,1.531 true 2.99,4.021 2.906,4.021 2.906,4.021 2.802,3.896 true 1.969,3.719 2.208,3.938 0.24,0.219 10 false *a 2.969,1.344 3.208,1.563 0.24,0.219 10 false *a 0.719,4.469 1.073,4.625 0.354,0.156 10 false SST 0.542,2.323 0.896,2.479 0.354,0.156 10 false SST 1.938,1.635 2.177,1.854 0.24,0.219 10 false *1 3.021,3.938 3.26,4.156 0.24,0.219 10 false *1
*1 Bimetal Formed Bushing
*a Depth


Using SST and a hammer, install 2 new bimetal formed bushings to the No. 2 reverse pre-balk head.

SST
09950-60010  (09951-00210)
09950-70010  (09951-07100)

Standard Depth:

0 to 1.0 mm (0 to 0.0394 in.)



b.

Secure the No. 2 reverse pre-balk head in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



c.
C325131C01
3,1.177 3.208,1.385 0.208,0.208 10 false *a
*a Height


Using a 3 mm pin punch and a hammer, install the straight pin to the No. 2 reverse pre-balk head.

Standard Height:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)



d.

Secure the No. 2 gear shift fork assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



e.

Install the No. 2 reverse pre-balk head to the No. 2 gear shift fork assembly as shown in the illustration.

C325132C01
1.177,0.646 1.406,0.208 1.406,0.208 1.542,0.208 false 0.375,1.854 0.51,1.854 0.51,1.854 0.615,1.406 false 1.25,1.573 1.479,1.135 1.479,1.135 1.615,1.135 true 0.958,1.313 1.625,0.781 1.625,0.781 1.792,0.781 true 1.604,0.115 1.948,0.323 0.344,0.208 10 false *1 0.188,1.771 0.469,2 0.281,0.229 10 false *2 1.677,1.052 1.99,1.208 0.313,0.156 10 false *3 1.865,0.677 2.208,0.906 0.344,0.229 10 false *4 2.99,0.927 3.281,1.167 0.292,0.24 10 false *a 6.146,0.75 6.448,0.979 0.302,0.229 10 false *b
*1 No. 2 Reverse Pre-balk Head *2 Torsion Spring
*3 Shift Lever Stopper *4 Straight Pin
*a Turn *b Push



f.
C325120

Install the spacer to the No. 2 gear shift fork assembly.


g.
C325133C01
1.208,1.115 1.375,0.969 1.375,0.969 1.5,0.969 false 2.677,0.458 2.792,0.281 2.792,0.281 2.917,0.281 false 2.969,0.188 3.281,0.375 0.313,0.188 10 false *1 1.573,0.896 1.833,1.146 0.26,0.25 10 false *a
*1 Snap Ring
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape and a hammer, install the snap ring to the No. 2 gear shift fork assembly.

HINT:

Use a piece of cloth to keep the snap ring from flying off.



Hide 25.INSTALL NO. 2 GEAR SHIFT HEAD

a.
C325118

Install the No. 2 gear shift head to the No. 2 gear shift fork assembly.


b.
C325134C01
2.99,0.104 3.26,0.292 0.271,0.188 10 false *a 3.156,0.302 3.427,0.49 0.271,0.188 10 false *a
*a Height


Using a 5 mm pin punch and a hammer, install the slotted spring pin to the No. 2 gear shift head.

Standard Height:

1.0 mm (0.0394 in.) or less



Hide 26.INSTALL NO. 1 GEAR SHIFT HEAD

a.

Secure the No. 1 gear shift fork assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C325109

Install the No. 1 gear shift head to the No. 1 gear shift fork assembly.


c.
C325110C01
2.583,1.073 2.896,1.229 0.313,0.156 10 false *a 2.49,1.594 2.802,1.75 0.313,0.156 10 false *a
*a Height


Using a 5 mm pin punch and a hammer, install the slotted spring pin to the No. 1 gear shift head.

Standard Height:

1.0 mm (0.0394 in.) or less



Hide 27.INSTALL INPUT SHAFT ASSEMBLY

a.

Apply gear oil to all sliding and rotating parts.


b.
C195713C02
1.604,1.094 1.604,1.781 1.604,1.781 1.906,1.781 false 1.698,2.75 1.969,2.75 false 1.948,1.698 2.177,1.927 0.229,0.229 10 *1 2,2.667 2.219,2.927 0.219,0.26 10 *2
*1 No. 1 Gear Shift Fork Shaft Assembly
*2 Output Shaft Assembly


Coat the No. 1 gear shift fork shaft assembly with gear oil and install it to the output shaft assembly.


c.
C195714C02
1.594,1.052 1.594,0.521 1.594,0.521 2.031,0.521 false 1.677,2.417 1.677,1.99 1.677,1.99 2.042,1.99 false 1.781,3.813 1.781,3.604 1.781,3.604 2.042,3.604 false 2.052,0.438 3.083,0.979 1.031,0.542 10 *1 2.083,1.906 3.115,2.448 1.031,0.542 10 *2 2.052,3.521 2.833,3.74 0.781,0.219 10 *3
*1 No. 2 Gear Shift Fork Shaft Assembly
*2 No. 3 Gear Shift Fork Shaft Assembly
*3 Input Shaft Assembly


Coat the No. 2 gear shift fork shaft assembly and No. 3 gear shift fork shaft assembly with gear oil and install them to the input shaft assembly.


d.

Temporarily install the output shaft assembly, input shaft assembly, No. 1 gear shift fork shaft assembly, No. 2 gear shift fork shaft assembly and No. 3 gear shift fork shaft assembly, and tie them with a rope or string.


e.
C194632

Install the input shaft assembly, output shaft assembly, No. 1 gear shift fork shaft assembly, No. 2 gear shift fork shaft assembly and No. 3 gear shift fork shaft assembly to the front transaxle case.


Hide 33257C 28.INSTALL OUTER SELECT LEVER OIL SEAL

a.
C194655C03
1.49,1.292 1.031,1.292 1.031,1.292 1.958,0.781 true 1.99,2.802 1.792,2.979 1.792,2.979 1.854,2.688 false 0.729,1.219 1.115,1.427 0.385,0.208 10 false SST 1.656,3.01 2.042,3.219 0.385,0.208 10 false SST 1.729,1.938 2.385,2.167 0.656,0.229 10 false *a
*a Depth


Using SST and a hammer, install a new outer select lever oil seal to the front transaxle case.

SST
09950-60010  (09951-00240)
09950-70010  (09951-07100)

Standard Depth:

0.5 to 1.0 mm (0.0197 to 0.0394 in.)



b.

Coat the lip of the outer select lever oil seal with MP grease.


Hide 33257 29.INSTALL OUTER SELECT LEVER

a.

Clean the bolt hole of the outer select lever.


b.
C194631C04
0.844,1.375 0.844,1.104 true 0.792,1.396 1.25,1.604 0.458,0.208 10 false *a
*a Mark


Install the outer select lever and inner select lever to the front transaxle case.

HINT:

Install the inner select lever with its mark facing the outside of the front transaxle case.



Hide 30.INSTALL SHIFT AND SELECT LEVER SHAFT ASSEMBLY

a.
C194733C07
1.74,1.365 1.917,1.271 1.917,1.271 2.677,1.271 true 0.51,3.771 0.604,3.125 0.604,3.125 0.781,3.125 true 1.625,0.604 1.74,0.521 1.74,0.521 2.417,0.521 true 2.469,0.438 2.667,0.635 0.198,0.198 10 false *1 2.74,1.188 2.938,1.385 0.198,0.198 10 false *3 0.844,3.052 1.042,3.25 0.198,0.198 10 false *2
*1 Shift and Select Lever Shaft Assembly
*2 Inner Select Lever
*3 Shift Inter Lock Plate


Turn the shift and select lever shaft assembly and shift inter lock plate counterclockwise, and install them to the front transaxle case.

HINT:

When installing the inner select lever, make sure to engage it with the shift inter lock plate.



b.

Clean the inner select lever set bolt.


c.
P000601C21
1.99,1.458 1.667,1.833 false 1.583,1.854 1.833,2.094 0.25,0.24 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the end of the inner select lever set bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

In order to ensure proper installation of the inner select lever set bolt, apply adhesive to the inner select lever set bolt and install it within 10 minutes of adhesive application.



d.
C194629

Using a 6 mm hexagon socket wrench, install the inner select lever set bolt.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


Hide 33240 31.INSTALL REVERSE SHIFT ARM BRACKET ASSEMBLY

a.
C194628

Install the reverse shift arm bracket assembly to the front transaxle case with the 2 bolts.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


Hide 32.INSTALL REVERSE SHIFT FORK

a.

Secure the No. 4 gear shift fork shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C325136

Install the reverse shift fork to the No. 4 gear shift fork shaft.


c.
C325137C01
2.417,2.427 2.625,2.646 0.208,0.219 10 false *a
*a Depth


Using a 5 mm pin punch and a hammer, install the slotted spring pin to the reverse shift fork.

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)



Hide 33.INSTALL REVERSE SHIFT FORK SHAFT ASSEMBLY

a.
C195709

Coat the reverse shift fork shaft assembly with gear oil and install it to the front transaxle case.


Hide 33402 34.INSTALL REVERSE IDLER GEAR SUB-ASSEMBLY

a.

Clean the reverse idler gear shaft bolt hole.


b.
C205132C11
2.729,2.031 2.708,1.51 2.708,1.51 3.031,1.51 true 0.76,4.313 0.938,4.313 0.938,4.313 1.135,4.094 true 2.396,2.052 2.479,2.052 2.479,2.052 2.521,1.948 false 0.76,0.75 0.958,0.75 0.958,0.75 1.688,2.26 true 2.667,1.021 2.76,1.021 2.76,1.021 2.896,0.74 true 3.083,1.427 3.313,1.646 0.229,0.219 10 true *a 0.583,4.229 0.896,4.427 0.313,0.198 10 false *c 2.25,1.958 2.479,2.177 0.229,0.219 10 false *c 0.573,0.677 0.802,0.896 0.229,0.219 10 false *b 2.51,0.958 2.74,1.177 0.229,0.219 10 false *b
*a Parallel
*b Reverse Idler Gear Shaft Bolt Hole
*c Screw Hole


Coat the reverse idler gear sub-assembly, reverse idler thrust washer and reverse idler gear shaft with gear oil, and install them to the front transaxle case as shown in the illustration.

NOTICE:

Make sure that the reverse idler gear shaft bolt hole is parallel to the screw hole on the front transaxle case.


HINT:

Raise the edge of the reverse shift arm bracket assembly and install it to the reverse shift fork shaft assembly.



Hide 33111 35.INSTALL MANUAL TRANSMISSION CASE

a.

Remove any remaining seal packing from the contact surfaces of the front transaxle case and manual transmission case.


b.
C194664C07
1.26,0.646 1.125,0.438 1.125,0.438 0.865,0.438 true 0.708,0.365 1.115,0.583 0.406,0.219 10 false *a
*a FIPG
(Seal Diameter 1.2 mm (0.0472 in.))


Apply FIPG to the manual transmission case as shown in the illustration.

FIPG:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the parts within 10 minutes of application. Otherwise, the seal packing (FIPG) must be removed and reapplied.




c.
C194730

Push the outer No. 1 shift lever and temporarily install the manual transmission case.

HINT:

Pushing on the outer No. 1 shift lever allows the manual transmission case to be temporarily installed.



d.
C194731

Pull the outer No. 1 shift lever out and turn it counterclockwise.


e.
C194620

Install the manual transmission case to the front transaxle case with the 16 bolts.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


Hide 33253F 36.INSTALL OUTER SHIFT LEVER E-RING

a.
C194622

Install the outer shift lever E-ring to the outer No. 1 shift lever.


Hide 43420H 37.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.
C193806C09
1.792,2.01 1.958,2.01 1.958,2.01 1.958,2.219 true 1.396,1.156 1.927,0.563 1.927,0.563 2.125,0.563 true 1.49,1.969 1.938,2.26 0.448,0.292 10 false SST 2.01,2.896 2.281,3.115 0.271,0.219 10 false *a 2.208,0.5 2.656,0.792 0.448,0.292 10 false SST
*a Depth


Using SST and a hammer, install a new front drive shaft oil seal LH to the manual transmission case.

SST
09316-60011  (09316-00011)

Standard Depth:

10.6 to 11.6 mm (0.417 to 0.457 in.)


NOTICE:

Do not damage the front drive shaft oil seal LH lip.



b.

Coat the lip of the front drive shaft oil seal LH with MP grease.


Hide 43410M 38.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.
C201403C03
1.552,1.198 2.802,0.927 2.802,0.927 2.156,1.552 true 1.771,1.292 2.792,0.938 false 1.521,2.375 1.521,2.677 1.521,2.677 0.917,2.479 false 1.24,2.344 1.521,2.677 false 2.875,0.802 3.219,1.031 0.344,0.229 10 false SST 1.417,2.698 1.76,2.927 0.344,0.229 10 false SST 0.99,2.698 1.333,2.927 0.344,0.229 10 false *a
*a Depth


Using SST and a hammer, install a new front drive shaft oil seal RH to the front transaxle case.

SST
09630-24014  (09620-24051)
09950-60010  (09951-00410, 09951-00530, 09952-06010)
09950-70010  (09951-07100)

Standard Depth:

1.2 to 2.2 mm (0.0472 to 0.0866 in.)


NOTICE:

Do not damage the front drive shaft oil seal RH lip.



b.

Coat the lip of thefront drive shaft oil seal RH with MP grease.


Hide 33275C 39.INSTALL SHIFT DETENT BALL

a.

Clean the shift detent ball plugs and installation holes in the manual transmission case.


b.
C324918C01
1.792,1.208 1.958,0.5 1.958,0.5 2.104,0.5 false 2.146,0.417 2.458,0.573 0.313,0.156 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the ends of the 2 shift detent ball plugs.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


NOTICE:

In order to ensure proper installation of the 2 shift detent ball plugs, apply adhesive to the 2 shift detent ball plugs and install them within 10 minutes of adhesive application.



c.
C194778

Install the 2 shift detent balls and 2 shift detent ball compression springs to the manual transmission case.


d.

Using a 6 mm hexagon socket wrench, install the 2 shift detent ball plugs to the manual transmission case.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)

NOTICE:

Be careful not to drop the shift detent balls into the manual transmission case.



e.

Clean the shift detent ball plug and installation hole in the manual transmission case.


f.
C324918C01
1.792,1.208 1.958,0.5 1.958,0.5 2.104,0.5 false 2.146,0.417 2.458,0.573 0.313,0.156 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the end of the shift detent ball plug.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


NOTICE:

In order to ensure proper installation of the shift detent ball plug, apply adhesive to the shift detent ball plug and install it within 10 minutes of adhesive application.



g.
C194618

Install the shift detent ball and shift detent ball compression spring to the manual transmission case.


h.

Using a 6 mm hexagon socket wrench, install the shift detent ball plug to the manual transmission case.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)

NOTICE:

Be careful not to drop the shift detent ball into the manual transmission case.



Hide 33292A 40.INSTALL LOCK BALL PIN

a.

Clean the shift and select lever shaft straight screw with head plug and installation holes in the manual transmission case.


b.
C324918C01
1.792,1.208 1.958,0.5 1.958,0.5 2.104,0.5 false 2.146,0.417 2.458,0.573 0.313,0.156 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the end of the shift and select lever shaft straight screw with head plug.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


NOTICE:

In order to ensure proper installation of the shift and select lever shaft straight screw with head plug, apply adhesive to the shift and select lever shaft straight screw with head plug and install it within 10 minutes of adhesive application.



c.
C194617

Install the lock ball pin and shift and select lever shaft compression spring to the manual transmission case.


d.

Using a 10 mm hexagon socket wrench, install the shift and select lever shaft straight screw with head plug to the manual transmission case.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 33451H 41.INSTALL REVERSE IDLER GEAR SHAFT BOLT

a.

Clean the reverse idler gear shaft bolt.


b.
P000601C21
1.99,1.458 1.667,1.833 false 1.583,1.854 1.833,2.094 0.25,0.24 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the end of the reverse idler gear shaft bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

In order to ensure proper installation of the reverse idler gear shaft bolt, apply adhesive to the reverse idler gear shaft bolt and install it within 10 minutes of adhesive application.



c.
C194616

Install the reverse idler gear shaft bolt and a new gasket to the manual transmission case.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 33290 42.INSTALL NO. 1 LOCK BALL ASSEMBLY

a.

Clean the No. 1 lock ball assembly and installation hole in the manual transmission case.


b.
C354664C02
1.969,1.104 1.542,0.688 false 1.375,0.583 1.688,0.74 0.313,0.156 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the end of the No. 1 lock ball assembly.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


NOTICE:

In order to ensure proper installation of the No. 1 lock ball assembly, apply adhesive to the No. 1 lock ball assembly and install it within 10 minutes of adhesive application.



c.
C194615

Install the No. 1 lock ball assembly to the manual transmission case.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


Hide 43.INSTALL TRANSMISSION CASE PLUG

a.
C297982

Install the transmission case plug and a new gasket to the manual transmission case.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


Hide 31121 44.INSTALL NO. 1 CLUTCH HOUSING COVER

a.
C194612

Install the No. 1 clutch housing cover to the front transaxle case.


Hide 45.INSTALL RELEASE CYLINDER BLEEDER PLUG

a.

Install the release cylinder bleeder plug to the clutch release bleeder sub-assembly.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


Hide 31478 46.INSTALL RELEASE CYLINDER BLEEDER PLUG CAP

a.

Install the release cylinder bleeder plug cap to the release cylinder bleeder plug.


Hide 31400 47.INSTALL CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY

Hide 31407B 48.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 49.INSPECT CLUTCH PIPE LINE

Hide 31407B 50.INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 51.INSTALL WIRE HARNESS CLAMP BRACKET

a.
C368125

Install the wire harness clamp bracket to the manual transmission case with the bolt.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


Hide 335A0 52.INSTALL CONTROL CABLE BRACKET ASSEMBLY

a.
C276945

Install the control cable bracket assembly to the manual transmission case with the 3 bolts.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


Hide 53.INSTALL NEUTRAL POSITION SWITCH

a.
C194604

Using a 27 mm deep socket wrench, install the neutral position switch and a new gasket to the manual transmission case.

Torque:
40.2 N*m (410 kgf*cm, 30 ft.*lbf)


Hide 84210 54.INSTALL BACK-UP LIGHT SWITCH ASSEMBLY

a.
C194603

Using a 27 mm deep socket wrench, install the back-up light switch assembly and a new gasket to the manual transmission case.

Torque:
40.2 N*m (410 kgf*cm, 30 ft.*lbf)


Hide 55.INSTALL TRANSMISSION REVOLUTION SENSOR

a.
C368124

Coat the O-ring with gear oil and install the transmission revolution sensor to the manual transmission case with the bolt.

Torque:
7.8 N*m (80 kgf*cm, 69 in.*lbf)

NOTICE:

When reusing the transmission revolution sensor, first inspect the O-ring. If the O-ring is damaged, replace the transmission revolution sensor with a new one.


HINT:

When installing the transmission revolution sensor rotate the sensor lightly by hand while inserting it into the hole in the manual transmission case.



Hide 33101A 56.INSTALL MANUAL TRANSMISSION FILLER PLUG

a.
C294797

Install the manual transmission filler plug and a new gasket to the manual transmission case.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)

HINT:

Face the tapered side of the gasket toward the manual transmission case.



Hide 33101B 57.INSTALL MANUAL TRANSMISSION DRAIN PLUG

a.
C295267

Using a 10 mm hexagon socket wrench, install the manual transmission drain plug and a new gasket to the front transaxle case.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)

HINT:

Face the tapered side of the gasket toward the front transaxle case.