Home › Drivetrain › EC6A (MANUAL TRANSMISSION / TRANSAXLE) › DIFFERENTIAL CASE
RM32H0E _52 Drivetrain _059609 EC6A MANUAL TRANSMISSION / TRANSAXLE _0295680 DIFFERENTIAL CASE A

EC6A MANUAL TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL FRONT DIFFERENTIAL SIDE GEAR

a.
C288461C02
0.771,0.688 0.635,0.302 0.635,0.302 0.552,0.302 false 1.719,0.74 1.583,0.333 1.583,0.333 1.5,0.333 false 2.5,0.708 2.365,0.323 2.365,0.323 2.281,0.323 false 0.406,0.229 0.719,0.385 0.313,0.156 10 false *1 1.323,0.25 1.635,0.406 0.313,0.156 10 false *2 2.104,0.25 2.417,0.406 0.313,0.156 10 false *3
*1 Front Differential Side Gear
*2 Conical Spring
*3 Front No. 1 Differential Side Gear Thrust Washer
V100135

Gear Oil


Coat the front differential side gear, front No. 1 differential side gear thrust washer and conical spring with gear oil.


b.
C304161C01
2.292,1.865 2.406,1.865 false 2.292,0.323 2.427,0.323 false 2.302,0.552 2.573,0.552 false 2.292,1.49 2.573,1.49 false 2.292,1.708 2.427,1.708 false 2.292,0.177 2.406,0.177 false 2.104,0.5 2.417,0.698 0.313,0.198 10 false *1 2.115,1.427 2.427,1.625 0.313,0.198 10 false *1 2.104,0.271 2.417,0.469 0.313,0.198 10 false *2 2.104,0.104 2.417,0.302 0.313,0.198 10 false *3 2.115,1.646 2.427,1.844 0.313,0.198 10 false *2 2.115,1.802 2.427,2 0.313,0.198 10 false *3
*1 Front Differential Side Gear
*2 Conical Spring
*3 Front No. 1 Differential Side Gear Thrust Washer


Install the 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and 2 conical springs to the front differential case assembly with ring gear.

NOTICE:
·

Do not drop the front differential side gear, front No. 1 differential side gear thrust washer or conical spring.

·

Make sure that the conical spring is installed with the correct orientation.




c.

Install SST as shown in the illustration and tighten it.

C290763C05
4.729,0.531 4.917,0.531 4.917,0.531 5.135,0.292 false 4.406,1.573 4.885,1.573 4.885,1.573 5.031,1.417 true 4.885,1.573 5.042,1.698 true 3.208,0.208 3.521,0.406 0.313,0.198 10 false *a 0.875,2.375 1.188,2.573 0.313,0.198 10 false *b 4.417,0.458 4.875,0.656 0.458,0.198 10 false SST 4.125,1.51 4.583,1.708 0.458,0.198 10 false SST
*a Turn *b Hold


SST
09528-52010  (09953-05010, 09528-05020)

NOTICE:

Do not overtighten SST as doing so will damage the front differential side gears, conical springs, front No. 1 differential side gear thrust washers and front differential case assembly with ring gear.


HINT:
·

Tighten SST to create the necessary clearance to install the front differential pinions.

·

When installing the front differential pinions, do not overtighten SST, as it is necessary to rotate the front differential side gears.




d.
C287727C02
0,0 0,0 false
V100135

Gear Oil


Coat the front differential pinion and front differential pinion thrust washer with gear oil.


e.
C290770C04
2.688,2.844 2.552,2.844 2.552,2.844 2.552,2.354 true 1.531,0.417 1.844,0.615 0.313,0.198 10 false *a 2.771,2.771 3.229,2.969 0.458,0.198 10 false SST
*a Turn


Using SST as shown in the illustration, rotate the front differential side gear and install the 2 front differential pinions and 2 front differential pinion thrust washers.

SST
09528-52010  (09528-05040)

CAUTION:

Be careful not to catch your fingers between the front differential pinion and front differential case assembly with ring gear.


NOTICE:

Do not drop the front differential pinion or front differential pinion thrust washer.



Hide 2.INSPECT FRONT DIFFERENTIAL PINION BACKLASH

Hide 41342F 3.INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C292331C01
0,0 0,0 false
V100135

Gear Oil


Coat the front No. 1 differential pinion shaft with gear oil.


b.

Install the front No. 1 differential pinion shaft to the front differential case assembly with ring gear so that the hole for the front differential pinion shaft straight pin is aligned with the hole in the front differential case assembly with ring gear.


Hide 41300 4.INSPECT FRONT DIFFERENTIAL CASE ASSEMBLY WITH RING GEAR

Hide 41342A 5.INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.
C263883

Using a 5 mm pin punch and a hammer, install the front differential pinion shaft straight pin to the front differential case assembly with ring gear.


b.
C290771

Using a chisel and hammer, stake the front differential case assembly with ring gear.