1.INSPECT 6TH GEAR THRUST CLEARANCE
2.INSPECT 5TH GEAR THRUST CLEARANCE
3.INSPECT 4TH GEAR THRUST CLEARANCE
4.INSPECT 3RD GEAR THRUST CLEARANCE
5.INSPECT 6TH GEAR RADIAL CLEARANCE
6.INSPECT 5TH GEAR RADIAL CLEARANCE
7.INSPECT 4TH GEAR RADIAL CLEARANCE
8.INSPECT 3RD GEAR RADIAL CLEARANCE
33311Y
9.REMOVE REAR INPUT SHAFT BEARING SHAFT SNAP RING
Using a snap ring expander, remove the rear input shaft bearing shaft snap ring.
33337
10.REMOVE 6TH GEAR SUB-ASSEMBLY
Using SST and a press, remove the rear input shaft radial ball bearing and 6th gear sub-assembly from the input shaft.
Do not tighten SST excessively.
Support the input shaft by hand to prevent it from dropping off.
33337A
11.REMOVE 6TH GEAR NEEDLE ROLLER BEARING
Remove the 6th gear needle roller bearing from the inner 6th gear bearing race.
33396C
12.REMOVE NO. 5 SYNCHRONIZER RING (for 6th Gear)
Remove the No. 5 synchronizer ring (for 6th gear) from the No. 3 transmission clutch hub.
3335A
13.REMOVE INNER 6TH GEAR BEARING RACE
Remove the inner 6th gear bearing race from the input shaft.
3335AA
14.REMOVE INNER 6TH GEAR BEARING RACE LOCK BALL
| *a | Magnet Hand |
Using a magnet hand, remove the inner 6th gear bearing race lock ball from the input shaft.
33395
15.REMOVE NO. 3 TRANSMISSION HUB SLEEVE
Remove the No. 3 transmission hub sleeve from the No. 3 transmission clutch hub.
33394
16.REMOVE NO. 3 SYNCHROMESH SHIFTING KEY
Remove the 3 No. 3 synchromesh shifting keys from the No. 3 transmission clutch hub.
33336
17.REMOVE 5TH GEAR
Using SST and a press, remove the No. 3 transmission clutch hub, No. 5 synchronizer ring (for 5th gear) and 5th gear from the input shaft.
Do not tighten SST excessively.
Support the input shaft by hand to prevent it from dropping off.
33336A
18.REMOVE 5TH GEAR NEEDLE ROLLER BEARING
Remove the 5th gear needle roller bearing from the inner 5th gear bearing race.
33359
19.REMOVE INNER 5TH GEAR BEARING RACE
Remove the inner 5th gear bearing race from the input shaft.
33359A
20.REMOVE INNER 5TH GEAR BEARING RACE LOCK BALL
| *a | Magnet Hand |
Using a magnet hand, remove the inner 5th gear bearing race lock ball from the input shaft.
33334
21.REMOVE 4TH GEAR
Remove the 4th gear from the input shaft.
33334A
22.REMOVE 4TH GEAR NEEDLE ROLLER BEARING
Remove the 4th gear needle roller bearing from the input shaft.
33381
23.REMOVE OUTER 2ND SYNCHRONIZER RING
Remove the outer 2nd synchronizer ring from the No. 2 transmission clutch hub.
33334B
24.REMOVE 4TH GEAR BEARING SPACER
Remove the 4th gear bearing spacer from the No. 2 transmission clutch hub.
33364
25.REMOVE NO. 2 TRANSMISSION HUB SLEEVE
Remove the No. 2 transmission hub sleeve from the No. 2 transmission clutch hub.
33366
26.REMOVE NO. 2 SYNCHROMESH SHIFTING KEY
Remove the 3 No. 2 synchromesh shifting keys from the No. 2 transmission clutch hub.
33362A
27.REMOVE NO. 2 CLUTCH HUB SETTING SHAFT SNAP RING
Using a snap ring expander, remove the No. 2 clutch hub setting shaft snap ring.
33333
28.REMOVE 3RD GEAR
Using SST and a press, remove the No. 2 transmission clutch hub, No. 3 synchronizer ring and 3rd gear from the input shaft.
Do not tighten SST excessively.
Support the input shaft by hand to prevent it from dropping off.
33333A
29.REMOVE 3RD GEAR NEEDLE ROLLER BEARING
Remove the 3rd gear needle roller bearing from the input shaft.
33311A
30.REMOVE FRONT INPUT SHAFT BEARING
Using a press, remove the front input shaft bearing from the input shaft.
Support the input shaft by hand to prevent it from dropping off.