Home › Power Source / Network › 8NR-FTS (BATTERY / CHARGING) › CHARGING SYSTEM › 2016.10–2021.09
RM32H0E _57 Power Source / Network _060209 8NR-FTS BATTERY / CHARGING _0295688 CHARGING SYSTEM C

8NR-FTS BATTERY / CHARGING  CHARGING SYSTEM  P161A87  Lost Communication with Alternator Missing Message  


DESCRIPTION

The ECM communicates with the generator assembly via LIN communication. If a LIN communication error is detected, the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory Note
P161A87 Lost Communication with Alternator Missing Message Generator assembly or ECM communication stops for approximately 17 minutes or more with the ignition switch ON
(1 trip detection logic)
·

Wire harness or connector

·

Generator assembly

·

ECM


Charge warning light does not come on DTC stored SAE Code: P161A

WIRING DIAGRAM

A331106E82
6.031,1.979 6.479,2.167 0.448,0.188 10 false ECM 6.042,1.823 6.5,2.021 0.458,0.198 10 false C62 5.865,0.729 6.323,0.927 0.458,0.198 10 false LIN 5.573,0.542 6.031,0.74 0.458,0.198 10 false 61 3.729,0.74 4.188,0.938 0.458,0.198 10 false LIN 4.094,0.531 4.552,0.729 0.458,0.198 10 false 2 2.698,0.74 3.156,0.938 0.458,0.198 10 false +B 2.448,0.583 2.906,0.781 0.458,0.198 10 false 1 1.667,0.854 2.573,1.167 0.906,0.313 10 false BATT-S 0.573,0.719 1.479,1.031 0.906,0.313 10 false from Battery 2.344,1.365 4.698,1.625 2.354,0.26 10 false Battery State Sensor Assembly 2.354,1.188 2.813,1.385 0.458,0.198 10 false C20 2.625,2.854 5,3.188 2.375,0.333 10 false Generator Assembly 2.625,2.688 3.083,2.885 0.458,0.198 10 false C37 3.719,2.208 4.177,2.406 0.458,0.198 10 false LIN 4.094,2.01 4.552,2.208 0.458,0.198 10 false 2 1.094,3.177 2.802,3.448 1.708,0.271 10 false : LIN Communication Line 0.146,0.156 2.5,0.417 2.354,0.26 12 false w/ Battery Current Sensor

A348065E16
1.552,3.083 5.219,3.281 3.667,0.198 10 false : LIN Communication Line 5.125,2.417 5.583,2.615 0.458,0.198 10 false C62 4.677,1.458 4.99,1.656 0.313,0.198 10 false 61 5.115,2.573 5.573,2.771 0.458,0.198 10 false ECM 4.938,1.625 5.25,1.823 0.313,0.198 10 false LIN 2.823,1.625 3.135,1.823 0.313,0.198 10 false LIN 3.135,1.469 3.448,1.667 0.313,0.198 10 false 2 1.698,2.125 2.135,2.323 0.438,0.198 10 false C37 1.688,2.292 4.031,2.563 2.344,0.271 10 false Generator Assembly 0.156,0.146 2.25,0.417 2.094,0.271 12 false w/o Battery Current Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before replacing the ECM, refer to Service Bulletin.



PROCEDURE

1.CHECK CHARGING SYSTEM

Result:
Result Proceed to
OK (w/ Battery Current Sensor) A
OK (w/o Battery Current Sensor) B
NG C



A

2.CHECK HARNESS AND CONNECTOR (ECM - GENERATOR ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (ECM - GENERATOR ASSEMBLY)

C

REPAIR OR REPLACE CHARGING SYSTEM

2.CHECK HARNESS AND CONNECTOR (ECM - GENERATOR ASSEMBLY)
a.

Disconnect the C62 ECM connector.


b.

Disconnect the C37 generator assembly connector.


c.

Disconnect the C20 battery state sensor assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C20-2 (LIN) or C37-2 (LIN) - C62-61 (LIN) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C20-2(LIN), C37-2 (LIN) or C62-61 (LIN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Check for DTCs, and then write them down.

Powertrain > Engine > Trouble Codes
50001 372

f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

h.

Turn the ignition switch off and wait 30 seconds.


Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Allow the engine to idle for approximately 17 minutes or more.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.


f.

Check for DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
Only DTC P161A87 is output. A
DTC P161A87 and P162B87 are output. B
DTCs are not output. C



A

B

C

5.CHECK HARNESS AND CONNECTOR (ECM - GENERATOR ASSEMBLY)
a.

Disconnect the C62 ECM connector.


b.

Disconnect the C37 generator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C37-2 (LIN) - C62-61 (LIN) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C37-2 (LIN) or C62-61 (LIN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR