Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › 2016.10–2019.09
RM32H0E _56 Audio / Visual / Telematics _060227 AUDIO / VIDEO _0295690 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B158F  AV Signal Stoppage (Low Battery Voltage)  


DESCRIPTION

This DTC is stored when a video or audio signal is interrupted due to battery voltage input to the radio and display receiver assembly dropping temporarily.

DTC No. Detection Item DTC Detection Condition Trouble Area
B158F AV Signal Stoppage (Low Battery Voltage) A video or audio signal is interrupted when the battery voltage drops
·

Radio and display receiver assembly

·

Harness or connector

·

Stop and start system*



*: w/ Stop and Start System


WIRING DIAGRAM

E277818E09
0.76,0.604 2.906,0.802 2.146,0.198 10 false from Battery*1 3.26,0.781 4.125,0.99 0.865,0.208 10 false RADIO*1 5.26,0.594 6.125,0.802 0.865,0.208 10 false +B1 5.083,0.479 5.948,0.688 0.865,0.208 10 false 4 2.281,1.385 3.146,1.594 0.865,0.208 10 false B42*2 2.781,1.26 3.646,1.469 0.865,0.208 10 false 12 1.479,1.646 2.344,1.854 0.865,0.208 10 false F77 1.479,1.781 3.625,1.979 2.146,0.198 10 false Engine Stop and Start ECU*2 5.052,1.927 5.917,2.135 0.865,0.208 10 false F126 5.052,2.094 6.76,2.469 1.708,0.375 10 false Radio and Display Receiver Assembly 0.156,2.125 2.302,2.323 2.146,0.198 10 false *1: w/o Stop and Start System 0.156,2.417 2.302,2.615 2.146,0.198 10 false *2: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E268487

Enter the "Vehicle Signal Check Mode" screen. Refer to Check Vehicle Signal in Operation Check.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>OPERATION CHECK


b.

Measure the battery voltage.

Standard Voltage:

11 to 14 V (w/o Stop and Start System)

9.5 to 14 V (w/ Stop and Start System)


HINT:

This display is updated once per second.



Result:
Result Proceed to
OK A
NG (w/o Stop and Start System) B
NG (w/ Stop and Start System) C



A

2.CHECK DTC

B

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)

C

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ENGINE STOP AND START ECU)
2.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)
a.

Disconnect the radio and display receiver assembly connector.


b.
E360341C03
1.479,0.427 1.927,0.667 0.448,0.24 2.438,1.625 2.156,1.115 true 2.385,1.646 3,1.844 0.615,0.198 10 false +B1 1.531,0.469 1.99,0.667 0.458,0.198 10 false F126 0.104,0.115 0.563,0.313 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F126-4 (+B1) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ENGINE STOP AND START ECU)
a.

Disconnect the F126 radio and display receiver assembly connector.


b.

Disconnect the F77 engine stop and start ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F126-4 (+B1) - F77-12 (B42) Always Below 1 Ω
F126-4 (+B1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)
a.

Disconnect the F126 radio and display receiver assembly connector.


b.

Reconnect the F77 engine stop and start ECU connector.


c.
E360341C03
1.479,0.427 1.927,0.667 0.448,0.24 2.438,1.625 2.156,1.115 true 2.385,1.646 3,1.844 0.615,0.198 10 false +B1 1.531,0.469 1.99,0.667 0.458,0.198 10 false F126 0.104,0.115 0.563,0.313 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F126-4 (+B1) - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

NG