Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › 2016.10–2019.09
RM32H0E _56 Audio / Visual / Telematics _060227 AUDIO / VIDEO _0295690 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

w/o Manual (SOS) Switch

The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

Using this circuit, the radio and display receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio and display receiver assembly.


w/ Manual (SOS) Switch

The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

Using this circuit, the telematics transceiver sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio and display receiver assembly via the telematics transceiver.


WIRING DIAGRAM

E344290E02
0.781,0.792 1.396,0.99 0.615,0.198 10 false MACC 0.792,1.26 1.406,1.458 0.615,0.198 10 false MCO+ 0.802,1.729 1.417,1.927 0.615,0.198 10 false MCO- 0.792,2.708 1.406,2.906 0.615,0.198 10 false SNS2 1.313,0.656 1.469,0.854 0.156,0.198 10 false 9 1.333,1.125 1.49,1.323 0.156,0.198 10 false 8 1.323,1.604 1.479,1.802 0.156,0.198 10 false 7 1.333,2.563 1.49,2.76 0.156,0.198 10 false 1 5.938,0.802 6.552,1 0.615,0.198 10 false MACC 5.948,1.26 6.563,1.458 0.615,0.198 10 false MIN+ 5.948,1.76 6.563,1.958 0.615,0.198 10 false MIN- 5.938,2.125 6.552,2.323 0.615,0.198 10 false SGND 5.927,2.708 6.542,2.906 0.615,0.198 10 false SNS2 3.25,2.24 4.781,2.438 1.531,0.198 10 false (Shielded) 0.208,3.135 0.667,3.333 0.458,0.198 10 false R2 0.229,3.302 2.302,3.698 2.073,0.396 10 false Map Light Assembly (Telephone Microphone Assembly) 5.75,3.135 6.208,3.333 0.458,0.198 10 false F125 5.74,3.302 6.979,4.021 1.24,0.719 10 false Radio and Display Receiver Assembly 0.094,4.438 3.615,4.635 3.521,0.198 12 false w/ Manual (SOS) Switch: 0.865,5.104 1.479,5.302 0.615,0.198 10 false SNS2 0.823,5.583 1.438,5.781 0.615,0.198 10 false MACC 0.833,6.052 1.448,6.25 0.615,0.198 10 false MCO+ 0.854,6.521 1.469,6.719 0.615,0.198 10 false MCO- 1.344,4.99 1.5,5.188 0.156,0.198 10 false 1 1.344,5.479 1.5,5.677 0.156,0.198 10 false 9 1.354,5.958 1.51,6.156 0.156,0.198 10 false 8 1.365,6.438 1.521,6.635 0.156,0.198 10 false 7 2.021,7.01 2.99,7.354 0.969,0.344 10 false (Shielded) 3.51,5.573 4.125,5.771 0.615,0.198 10 false MCVD 3.51,6.052 4.125,6.25 0.615,0.198 10 false MCI+ 3.51,6.542 4.125,6.74 0.615,0.198 10 false MCI- 3.5,6.896 4.115,7.094 0.615,0.198 10 false SGND 3.99,6.063 4.604,6.26 0.615,0.198 10 false MCO+ 4,6.521 4.615,6.719 0.615,0.198 10 false MCO- 3.24,5.479 3.552,5.677 0.313,0.198 10 false 33 3.24,5.958 3.552,6.156 0.313,0.198 10 false 34 3.24,6.427 3.552,6.625 0.313,0.198 10 false 35 3.24,6.781 3.552,6.979 0.313,0.198 10 false 32 4.427,5.958 4.74,6.156 0.313,0.198 10 false 18 4.427,6.438 4.74,6.635 0.313,0.198 10 false 19 4.813,7 5.729,7.281 0.917,0.281 10 false (Shielded) 5.729,5.948 5.885,6.146 0.156,0.198 10 false 5 5.667,6.438 5.979,6.635 0.313,0.198 10 false 19 5.667,6.781 5.979,6.979 0.313,0.198 10 false 18 5.719,4.99 5.875,5.188 0.156,0.198 10 false 6 5.927,5.104 6.542,5.302 0.615,0.198 10 false SNS2 5.927,6.063 6.542,6.26 0.615,0.198 10 false MIN+ 5.938,6.531 6.552,6.729 0.615,0.198 10 false MIN- 5.927,6.875 6.542,7.073 0.615,0.198 10 false SGND 5.76,7.375 6.219,7.573 0.458,0.198 10 false F125 5.75,7.542 6.969,8.146 1.219,0.604 10 false Radio and Display Receiver Assembly 3.365,7.365 3.76,7.615 0.396,0.25 10 false F51 3.385,7.521 4.958,7.938 1.573,0.417 10 false Telematics Transceiver 0.26,7.365 0.719,7.563 0.458,0.198 10 false R2 5.719,0.688 5.875,0.885 0.156,0.198 10 false 4 5.719,1.156 5.875,1.354 0.156,0.198 10 false 5 5.667,1.635 5.979,1.833 0.313,0.198 10 false 19 5.667,2.021 5.979,2.219 0.313,0.198 10 false 18 5.708,2.583 5.865,2.781 0.156,0.198 10 false 6 0.115,0.094 2.427,0.427 2.313,0.333 12 false w/o Manual (SOS) Switch: 0.26,7.563 2.333,7.958 2.073,0.396 10 false Map Light Assembly (Telephone Microphone Assembly)

PROCEDURE

1.CHECK MICROPHONE (OPERATION CHECK)
a.
E277821

Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>OPERATION CHECK


b.

When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check result is normal.



Result:
Result Proceed to
OK A
NG (w/o Manual (SOS) Switch) B
NG (w/ Manual (SOS) Switch) C



A

B

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

C

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the F125 radio and display receiver assembly connector.


b.

Disconnect the R2 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F125-6 (SNS2) - R2-1 (SNS2) Always Below 1 Ω
F125-4 (MACC) - R2-9 (MACC) Always Below 1 Ω
F125-5 (MIN+) - R2-8 (MCO+) Always Below 1 Ω
F125-19 (MIN-) - R2-7 (MCO-) Always Below 1 Ω
F125-6 (SNS2) - Body ground Always 10 kΩ or higher
F125-4 (MACC) - Body ground Always 10 kΩ or higher
F125-5 (MIN+) - Body ground Always 10 kΩ or higher
F125-19 (MIN-) - Body ground Always 10 kΩ or higher
F125-18 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Reconnect the F125 radio and display receiver assembly connector.


b.

Reconnect the R2 map light assembly (telephone microphone assembly) connector.


c.
E359760C03
1.427,0.625 1.896,0.917 0.469,0.292 1.115,2.635 2.052,1.99 true 2.24,1.75 2.917,1.344 true 2.219,2 2.635,2.563 true 0.167,0.125 0.479,0.323 0.313,0.198 10 false *a 1.542,0.688 2.313,0.854 0.771,0.167 10 false F125 2.938,1.167 3.427,1.479 0.49,0.313 10 false MACC 2.594,2.625 3.052,2.875 0.458,0.25 10 false SGND 0.865,2.625 1.25,2.844 0.385,0.219 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F125-4 (MACC) - Body ground Ignition switch ACC 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F125-18 (SGND) - Body ground Always Below 1 Ω
F125-19 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the map light assembly (telephone microphone assembly).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E358190C06
2.281,1.094 2.552,0.49 true 2.292,1.427 2.583,1.771 true 0.25,0.198 0.563,0.396 0.313,0.198 10 false *a 2.479,0.302 2.948,0.521 0.469,0.219 10 false SNS2 2.583,1.771 3.219,1.958 0.635,0.188 10 false MCO-
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SNS2) - 7 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

5.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Reconnect the F125 radio and display receiver assembly connector.


b.

Reconnect the R2 map light assembly (telephone microphone assembly) connector.


c.

Turn the ignition switch to ACC.


d.
E358189C03
1.542,0.49 1.969,0.75 0.427,0.26 2.188,1.75 2.708,2.177 true 1.99,1.781 2.208,2.385 true 0.219,0.177 0.531,0.375 0.313,0.198 10 false *a 1.646,0.521 1.958,0.719 0.313,0.198 10 false R2 2.76,2.188 3.198,2.458 0.438,0.271 10 false MCO- 2.115,2.427 2.604,2.698 0.49,0.271 10 false MCO+
*a Component with harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Connect an oscilloscope to terminals 8 (MCO+) and 7 (MCO-) of the R2 map light assembly (telephone microphone assembly) connector.


e.

Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.

Result:
Result Proceed to
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output. A
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output. B




A

B

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the F125 radio and display receiver assembly connector.


b.

Disconnect the R2 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F125-6 (SNS2) - R2-1 (SNS2) Always Below 1 Ω
F125-6 (SNS2) or R2-1 (SNS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the F51 telematics transceiver connector.


b.

Disconnect the R2 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F51-33 (MCVD) - R2-9 (MACC) Always Below 1 Ω
F51-34 (MCI+) - R2-8 (MCO+) Always Below 1 Ω
F51-35 (MCI-) - R2-7 (MCO-) Always Below 1 Ω
F51-33 (MCVD) or R2-9 (MACC) - Body ground Always 10 kΩ or higher
F51-34 (MCI+) or R2-8 (MCO+) - Body ground Always 10 kΩ or higher
F51-35 (MCI-) or R2-7 (MCO-) - Body ground Always 10 kΩ or higher
F51-32 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)
a.

Disconnect the F125 radio and display receiver assembly connector.


b.

Disconnect the F51 telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F125-5 (MIN+) - F51-18 (MCO+) Always Below 1 Ω
F125-19 (MIN-) - F51-19 (MCO-) Always Below 1 Ω
F125-5 (MIN+) or F51-18 (MCO+) - Body ground Always 10 kΩ or higher
F125-19 (MIN-) or F51-19 (MCO-) - Body ground Always 10 kΩ or higher
F125-18 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Reconnect the F125 radio and display receiver assembly connector.


b.

Disconnect the F51 telematics transceiver connector.


c.
E289390C46
1.521,0.698 1.938,0.948 0.417,0.25 2.635,2.625 2.229,1.99 true 2.063,2.771 2.063,1.969 true 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a 1.583,0.729 2.073,0.896 0.49,0.167 10 false F125 2.604,2.667 3.125,2.875 0.521,0.208 10 false SGND 2.01,2.802 2.531,3.01 0.521,0.208 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F125-18 (SGND) - Body ground Always Below 1 Ω
F125-19 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.INSPECT TELEMATICS TRANSCEIVER

NG

10.INSPECT TELEMATICS TRANSCEIVER
a.

Reconnect the F51 telematics transceiver connector.


b.
E259127C50
1.479,0.708 1.917,0.979 0.438,0.271 0.573,2.719 1.177,2.094 true 1.188,2.729 1.385,2.094 true 1.99,2.74 1.49,2.094 true 0.167,0.167 0.417,0.333 0.25,0.167 10 false *a 1.573,0.76 2.042,0.979 0.469,0.219 10 false F51 0.302,2.74 0.719,2.906 0.417,0.167 10 false MCI- 0.833,2.781 1.333,2.948 0.5,0.167 10 false MCVD 1.99,2.771 2.49,2.938 0.5,0.167 10 false SGND
*a Component with harness connected
(Telematics Transceiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F51-33 (MCVD) - Body ground Ignition switch ACC 4 to 6 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F51-32 (SGND) - Body ground Always Below 1 Ω
F51-35 (MCI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

11.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the map light assembly (telephone microphone assembly).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E358190C05
2.281,1.094 2.552,0.49 true 2.292,1.427 2.583,1.771 true 0.25,0.198 0.563,0.396 0.313,0.198 10 false *a 2.479,0.302 2.948,0.521 0.469,0.219 10 false SNS2 2.583,1.771 3.083,2.021 0.5,0.25 10 false MCO-
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SNS2) - 7 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

12.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Reconnect the F125 radio and display receiver assembly connector.


b.

Reconnect the R2 map light assembly (telephone microphone assembly) connector.


c.

Reconnect the F51 telematics transceiver connector.


d.

Turn the ignition switch to ACC.


e.
E358189C02
1.542,0.49 1.969,0.75 0.427,0.26 2.188,1.75 2.708,2.177 true 1.99,1.781 2.208,2.385 true 0.219,0.177 0.531,0.375 0.313,0.198 10 false *a 1.646,0.521 1.958,0.719 0.313,0.198 10 false R2 2.76,2.188 3.198,2.458 0.438,0.271 10 false MCO- 2.115,2.427 2.604,2.698 0.49,0.271 10 false MCO+
*a Component with harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Connect an oscilloscope to terminals 8 (MCO+) and 7 (MCO-) of the R2 map light assembly (telephone microphone assembly) connector.


f.

Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.

Result:
Result Proceed to
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output. A
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output. B




A

B

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)