Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › 2016.10–2019.09
RM32H0E _51 Engine / Hybrid System _059427 STOP AND START _0295332 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  P0831  Clutch Pedal Switch "A" Circuit Low  


DESCRIPTION

The clutch stroke sensor assembly (for detecting pedal depression amount) and clutch switch assembly (for detecting the pedal depression endpoint) are installed to the clutch pedal. When the engine is stopped by stop and start control, the engine stop and start control ECU receives the clutch pedal depression start signal from the clutch stroke sensor, and starts the engine.

When the engine stop and start control ECU detects the clutch stroke sensor ON signal and clutch switch ON signal are input simultaneously for 1.2 seconds or more, it stores a DTC and flashes the stop and start cancel indicator light.

A395503E01
2.74,3.052 2.292,2.51 false 3.604,3.281 4.656,1.771 true 0.99,4.042 1.823,4.375 0.833,0.333 10 false Clutch Pedal Released 6.094,4.063 6.906,4.427 0.813,0.365 10 false Clutch Pedal Depressed 0.042,2.25 0.927,2.781 0.885,0.531 10 false Clutch pedal stroke sensor signal 0.042,3.375 0.875,3.729 0.833,0.354 10 false Clutch switch signal 0,1.135 1.229,1.708 1.229,0.573 10 false Clutch pedal stroke sensor output characteristics 4.76,1.667 6.156,1.927 1.396,0.26 10 false Abnormal condition 1.156,0.938 1.615,1.135 0.458,0.198 10 false 100 1.26,1.885 1.417,2.083 0.156,0.198 10 false 0 1.156,2.219 1.469,2.417 0.313,0.198 10 false ON 1.167,3.229 1.479,3.427 0.313,0.198 10 false ON 1.094,2.708 1.552,2.906 0.458,0.198 10 false OFF 1.115,3.531 1.573,3.729 0.458,0.198 10 false OFF 0.083,0.094 1.615,0.292 1.531,0.198 10 false Reference: 1.583,2.344 2.188,2.885 0.604,0.542 10 false DTC Detection Condition

HINT:

The normal signal conditions are as shown in the table below.

Signal Clutch Pedal Released In Transition Clutch Pedal Depressed
Clutch pedal stroke sensor ON OFF OFF
Clutch switch OFF OFF ON

The ECM receives the ON and OFF signals from the clutch stroke sensor, and sends them to the engine stop and start control ECU using CAN communication.


DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P0831 Clutch Pedal Switch "A" Circuit Low Conditions (a) and (b) are met for 1.2 seconds or more (1 trip detection logic):
(a) Ignition switch ON
(b) Clutch switch is on when Clutch pedal stroke sensor signal is on.
·

Clutch switch assembly

·

Wire harness or connector

·

Engine stop and start ECU


Blinking DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared even automatically if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery temperature at 11°C (51°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine.


e.
A206932E06
1.302,1.948 1.302,2.708 false 1.594,1.948 1.594,2.708 false 1.323,2.167 1.865,2.167 false 1.365,2.208 1.323,2.167 1.323,2.167 1.365,2.135 false 1.823,2.135 1.865,2.167 1.865,2.167 1.823,2.208 false 1.708,2.167 1.958,2.74 true 1.469,2.167 1.208,2.74 true 1.542,2.135 1.594,2.167 1.594,2.167 1.542,2.208 false 1.635,2.208 1.594,2.167 1.594,2.167 1.635,2.135 false 1.875,1.927 1.875,2.708 false 0.135,0.115 1.458,0.302 1.323,0.188 10 false Clutch Switch Signal 1.99,2.719 3.135,2.906 1.146,0.188 10 false 1 second or more 0.281,2.719 1.052,3.031 0.771,0.313 10 false 1 second or more 0.583,1.177 0.833,1.333 0.25,0.156 10 false ON 0.583,1.854 0.896,2.01 0.313,0.156 10 false OFF

Fully depress the clutch pedal for 1 second or more. Release the clutch pedal and wait for at least 1 second.


f.

Repeat the previous step 3 times.


g.

Check that no DTCs are output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227


STOP AND START SYSTEM OPERATION CHECK


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery temperature at 11°C (51°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.



a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



d.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


e.

Allow the engine to stop by stop and start control.


f.

Depress the clutch pedal and start the engine.



WIRING DIAGRAM

A392131E01
0.052,1.938 0.51,2.135 0.458,0.198 10 false A47 0.063,2.104 1.313,2.5 1.25,0.396 10 false Clutch Pedal Stroke Sensor Assembly 0.813,0.802 1.271,1 0.458,0.198 10 false OUT 0.813,1.177 1.271,1.375 0.458,0.198 10 false VDD 0.802,1.583 1.26,1.781 0.458,0.198 10 false GND 1.219,0.698 1.375,0.896 0.156,0.198 10 false 2 1.219,1.104 1.375,1.302 0.156,0.198 10 false 3 1.208,1.5 1.365,1.698 0.156,0.198 10 false 1 1.75,0.594 2.208,0.792 0.458,0.198 10 false 119 1.76,0.802 2.219,1 0.458,0.198 10 false C62 1.76,1.198 2.219,1.396 0.458,0.198 10 false C62 1.76,1.594 2.219,1.792 0.458,0.198 10 false C62 1.802,1.01 2.115,1.208 0.313,0.198 10 false 89 1.802,1.417 2.115,1.615 0.313,0.198 10 false 87 2.104,0.802 2.563,1 0.458,0.198 10 false CLS 2.104,1.208 2.719,1.406 0.615,0.198 10 false VCCL 2.104,1.604 2.719,1.802 0.615,0.198 10 false E2CL 2.531,0.885 3.146,1.083 0.615,0.198 10 false CANH 2.531,1.333 3.146,1.531 0.615,0.198 10 false CANL 2.625,1.833 3.083,2.031 0.458,0.198 10 false STA 2.573,2.25 3.031,2.448 0.458,0.198 10 false NSW 3.01,0.896 3.469,1.094 0.458,0.198 10 false A38 3.01,1.344 3.469,1.542 0.458,0.198 10 false A38 3.01,1.833 3.469,2.031 0.458,0.198 10 false A38 3.01,2.24 3.469,2.438 0.458,0.198 10 false A38 3.042,0.688 3.354,0.885 0.313,0.198 10 false 13 3.042,1.146 3.354,1.344 0.313,0.198 10 false 26 3.042,1.646 3.354,1.844 0.313,0.198 10 false 29 3.042,2.042 3.354,2.24 0.313,0.198 10 false 57 2.333,2.719 2.792,2.917 0.458,0.198 10 false ECM 0.604,3.552 1.677,3.75 1.073,0.198 10 false J/B BAT 1.51,3.563 1.969,3.76 0.458,0.198 10 false AM2 2.156,3.76 2.615,3.958 0.458,0.198 10 false F12 2.156,3.917 3.281,4.302 1.125,0.385 10 false Ignition or Starter Switch Assembly 2.031,3.26 2.188,3.458 0.156,0.198 10 false 5 3.26,3.271 3.417,3.469 0.156,0.198 10 false 6 2.906,3.271 3.365,3.469 0.458,0.198 10 false ST1 2.229,3.271 2.688,3.469 0.458,0.198 10 false AM1 4.115,3.281 4.271,3.479 0.156,0.198 10 false 2 4.958,3.281 5.115,3.479 0.156,0.198 10 false 1 3.844,3.635 4.302,3.833 0.458,0.198 10 false A51 3.844,3.792 5.406,4.25 1.563,0.458 10 false Clutch Switch Assembly 1.927,4.729 2.24,4.927 0.313,0.198 10 false ST 4.01,5.635 4.323,5.833 0.313,0.198 10 false ST 0.479,5.177 1.854,5.375 1.375,0.198 10 false BATT-MAIN 0.604,6.729 1.677,6.927 1.073,0.198 10 false Battery 3.708,4.844 3.865,5.042 0.156,0.198 10 false 3 4.396,4.865 4.552,5.063 0.156,0.198 10 false 5 3.708,5.26 3.865,5.458 0.156,0.198 10 false 1 4.396,5.26 4.552,5.458 0.156,0.198 10 false 2 1.365,7.406 3.813,7.604 2.448,0.198 10 false Starter Assembly 4.271,7.156 6.188,7.375 1.917,0.219 10 false : CAN Communication Line 6.021,6.292 7.073,6.729 1.052,0.438 10 false Engine Stop and Start ECU 5.813,5.729 6.271,5.927 0.458,0.198 10 false A62 5.813,3.396 6.271,3.594 0.458,0.198 10 false A62 5.813,2.24 6.271,2.438 0.458,0.198 10 false A62 5.823,0.885 6.281,1.083 0.458,0.198 10 false F77 5.823,1.344 6.281,1.542 0.458,0.198 10 false F77 5.854,3.188 6.167,3.385 0.313,0.198 10 false 21 5.854,2.031 6.167,2.229 0.313,0.198 10 false 17 5.885,5.521 6.042,5.719 0.156,0.198 10 false 6 5.854,0.688 6.167,0.885 0.313,0.198 10 false 13 5.854,1.135 6.167,1.333 0.313,0.198 10 false 14 6.167,0.885 6.781,1.083 0.615,0.198 10 false CANH 6.177,1.333 6.792,1.531 0.615,0.198 10 false CANL 6.188,3.375 6.646,3.573 0.458,0.198 10 false STA 6.188,2.229 6.646,2.427 0.458,0.198 10 false CLL 6.188,5.719 6.802,5.917 0.615,0.198 10 false DGND 1.635,6.01 2.094,6.208 0.458,0.198 10 false C67 2.354,6.021 2.813,6.219 0.458,0.198 10 false C35 1.385,5.99 1.542,6.188 0.156,0.198 10 false 1 2.125,5.99 2.281,6.188 0.156,0.198 10 false 1 2.552,6.26 2.865,6.458 0.313,0.198 10 false ST

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION



HINT:

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA


PROCEDURE

1.READ VALUE USING GTS (CLUTCH LOWER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / Clutch Lower SW.

Powertrain > Stop and Start > Data List
Tester Display
Clutch Lower SW
50003 227 11

e.

Depress the clutch pedal and read the values displayed on the GTS.

OK:
Tester Display Condition Normal Condition
Clutch Lower SW Fully Depressed ON
Clutch Lower SW Fully Released OFF



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT CLUTCH SWITCH ASSEMBLY
2.INSPECT CLUTCH SWITCH ASSEMBLY
a.

Inspect the clutch switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - CLUTCH START SWITCH ASSEMBLY)

NG

REPLACE CLUTCH SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the A62 engine stop and start ECU connector.


b.

Disconnect the A51 clutch switch assembly connector.


c.

Disconnect the F12 ignition or starter switch assembly connector.


d.

Disconnect the A38 ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A62-17 (CLL) - A51-2 Always Below 1 Ω
A62-17 (CLL) - Body ground and other terminals Always 10 kΩ or higher
A51-2 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR