Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM32H0E _54 Brake _060039 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294918 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Brake Hold Operated Indicator Light Circuit  


DESCRIPTION

The brake hold operated indicator light illuminates when the brake hold system is operating (vehicle stopped due to brake fluid pressure hold) and turns off when the brake hold system operation is finished (brake fluid pressure decreases).

The brake hold system may not operate depending on vehicle conditions even when the system is in standby mode and the brake hold standby indicator light is illuminated.

When a malfunction occurs in the brake control system, the brake hold operated indicator light blinks.

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.PRE-CHECK
a.

Check that the brake hold standby indicator light operates normally.


b.

If the brake hold operated indicator light does not illuminate although the brake hold standby indicator light is illuminated, check that the following brake hold operation (maintaining brake oil pressure) conditions are met.

1.

Shift lever is not P or R. (for Continuously Variable Transaxle)

2.

Shift lever is not in neutral. (for Manual Transaxle)

3.

Driver is depressing brake pedal and vehicle is fully stopped.

4.

Driver is not depressing accelerator pedal.

5.

Vehicle is not on steep decline.


HINT:

When a malfunction occurs in the brake control system, the brake hold operated indicator light blinks.


Result:
Proceed to
NEXT




NEXT

2.INSPECT COMBINATION METER ASSEMBLY
2.INSPECT COMBINATION METER ASSEMBLY
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch off.


c.

Perform the Active Test of the combination meter assembly using the GTS.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. Hold
50004 122 71

d.

Check the combination meter assembly.

OK:

The brake hold operated indicator light turns on or off in accordance with the GTS operation.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (BRAKE HOLD OPERATED INDICATOR LIGHT)

NG

3.PERFORM ACTIVE TEST USING GTS (BRAKE HOLD OPERATED INDICATOR LIGHT)
a.

Turn the ignition switch to ON.


b.

Select the Active Test on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC/EPB > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
BH Operated Light Brake hold operated indicator light Indicator light ON/OFF Observe combination meter

c.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
BH Operated Light Brake hold operated indicator light ON or OFF ON: Indicator light on
OFF: Indicator light off
-
Chassis > ABS/VSC/TRC/EPB > Active Test
Active Test Display
BH Operated Light
Data List Display
BH Operated Light
50004 105 74 281

d.

Check the operating condition of the brake hold operated indicator light when operating it using the GTS.

Result:
Result Proceed to
Brake hold operated indicator light in the Data List does not change using the Active Test. (for LHD) A
Brake hold operated indicator light in the Data List does not change using the Active Test. (for RHD) B
Brake hold operated indicator light in the Data List turns ON/OFF using the Active Test. C




A

B

C