Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM32H0E _54 Brake _060039 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294918 VEHICLE STABILITY CONTROL SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  DTC CHECK / CLEAR  


DTC CHECK/CLEAR (When Using GTS)


a.

Check for DTCs.

i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Read the DTCs following the prompts on the GTS. Enter the following menus: Chassis / ABS/VSC/TRC/EPB / Trouble Codes.

Chassis > ABS/VSC/TRC/EPB > Trouble Codes
50001 105

vi.

Check the details of the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

NOTICE:

The vehicle stability control system outputs DTCs for the following system. When DTCs other than those in Diagnostic Trouble Code Chart for the vehicle stability control system are output, refer to Diagnostic Trouble Code Chart for the relevant system.

System Proceed to
Electric Parking Brake System (Click here)




b.

Clear the DTCs.

i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Operate the GTS to clear the codes. Enter the following menus: Chassis / ABS/VSC/TRC/EPB / Trouble Codes.

Chassis > ABS/VSC/TRC/EPB > Clear DTCs
50002 105

vi.

Press the DTC clear button.




DTC CHECK/CLEAR (When Using SST Check Wire)


a.

Check for DTCs.

i.

Turn the ignition switch off.


ii.
C368533C01
1.594,0.917 2.01,0.5 true 1.365,1.885 1.781,1.469 true 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 2.083,0.396 2.396,0.552 0.313,0.156 10 false CG 1.125,1.781 1.438,1.938 0.313,0.156 10 false TC
*a Front view of DLC3


Using SST, connect terminals TC and CG of the DLC3.

SST
09843-18040  


iii.

Turn the ignition switch to ON.


iv.

Observe the blinking pattern of the ABS warning, slip indicator and brake hold standby indicator lights in order to identify the DTC.

HINT:

If no code appears, inspect the TC and CG terminal circuit, and ABS warning, slip indicator and brake hold standby indicator light circuits.

Trouble Area See Procedure
TC and CG terminal circuit (Click here)
ABS warning light circuit (Remains on) (Click here)
ABS warning light circuit (Does not come on) (Click here)
Slip indicator light circuit (Remains on) (Click here)
Slip indicator light circuit (Does not come on) (Click here)
Brake hold standby indicator light circuit (Click here)



v.

Count the number of blinks of the ABS warning and slip indicator lights.

HINT:
·

When the system is operating correctly, each light will blink continuously in a pattern of 0.25 seconds on, and then 0.25 seconds off.

·

When one DTC is output, each light will output the same code at 4 second intervals (for example, code 21 would be output as 2 blinks, a 1.5 second pause, and then 1 blink).

·

When 2 or more DTCs are output, each light will output a different code at 2.5 second intervals, and when all codes have been output, there will be a 4 second pause and the sequence will repeat.

·

When multiple codes are stored, they are output in order starting with the lowest DTC number.

·

If the brake hold operated indicator light is blinking before terminals of the DLC3 are connected, when terminals 13 (TC) and 4 (CG) of the DLC3 are connected, the brake hold operated indicator light stops blinking and turns off.




vi.

Check the details of the DTCs.

ABS DTC
ABS Warning Light Display Tester Display
11 C146E
13 C146C
21 C1468
22 C1469
23 C146A
24 C146B
25 C1225
26 C1226
27 C1227
28 C1228
31 C1464
32 C1465
33 C1466
34 C1467
35 C1330
36 C1331
37 C1237
38 C1332
39 C1333
41 C1241
C1417
43 C1243
44 C1419
C1420
C1474
45 C1245
46 C1246
49 C1249
C1425
C1426
51 C1428
62 C1300
67 C1429
C1430
C1431
94 U0073
95 U0124
97 C1381

VSC DTC
Slip Indicator Light Display Tester Display
28 C1472
C1474
31 C1432
C1433
C1434
C1439
C1445
32 C1419
C1420
34 C1234
C1435
C1436
39 C1336
43*1 -
44 C1224
51 C1201
62 U0123
64 C1380
63 U0126
65 U0100
6A*2 C1381
88 C1288
98 C1448
- C1441

Brake Hold DTC
Warning Light Display Tester Display
11*3 -
14*4 -
58 U0142

*1: This DTC is output when the VSC system detects a malfunction in the ABS.

*2: The light blinks 6 times, turns off for 1.5 seconds, and then blinks 10 times.

*3: This DTC is output when the Brake Hold system detects a malfunction in the VSC.

*4: This DTC is output when the Brake Hold system detects a malfunction in the EPB.



vii.

After completing the check, disconnect terminals TC and CG of the DLC3 to turn off the display.

If 2 or more DTCs are detected at the same time, the DTCs will be displayed in ascending order.



b.

Clear the DTCs.

i.

Turn the ignition switch off.


ii.
C368533C01
1.594,0.917 2.01,0.5 true 1.365,1.885 1.781,1.469 true 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 2.083,0.396 2.396,0.552 0.313,0.156 10 false CG 1.125,1.781 1.438,1.938 0.313,0.156 10 false TC
*a Front view of DLC3


Using SST, connect terminals TC and CG of the DLC3.

SST
09843-18040  


iii.

Turn the ignition switch to ON.


iv.

Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.


v.

Check that the ABS warning and slip indicator lights indicate the normal system code.


vi.

Remove SST from the terminals of the DLC3.

HINT:

The DTCs cannot be cleared by disconnecting the battery terminal or the ECU-IG NO. 1 fuse.





END OF DTC CHECK/CLEAR


a.

Turn the ignition switch to ON.


b.

Check that the ABS warning and slip indicator lights go off within approximately 3 seconds of turning the ignition switch to ON.