Home › Engine / Hybrid System › CRUISE CONTROL › FORWARD RECOGNITION CAMERA SYSTEM › 2016.10–2020.08
RM32H0E _51 Engine / Hybrid System _059516 CRUISE CONTROL _0297891 FORWARD RECOGNITION CAMERA SYSTEM C

CRUISE CONTROL  FORWARD RECOGNITION CAMERA SYSTEM  C1AA8  Front Camera Module Incorrect Axial Gap  C1AA9  Front Camera Module Beam Axis Not Adjusted  


DESCRIPTION

If the forward recognition camera detects that the forward recognition camera axis has deviated, DTC C1AA8 is stored. Also, if Forward Recognition Camera Axis Adjustment is not performed after installing the forward recognition camera, DTC C1AA9 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AA8 Front Camera Module Incorrect Axial Gap When the vehicle is being driven at a speed of 1 km/h (1 mph) or more 3 seconds after the ignition switch is turned to ON, the forward recognition camera detects forward recognition camera axis deviation.
·

Forward recognition camera

·

Windshield glass


C1AA9 Front Camera Module Beam Axis Not Adjusted When the vehicle is being driven at a speed of 1 km/h (1 mph) or more 3 seconds after the ignition switch is turned to ON, the forward recognition camera detects that Forward Recognition Camera Axis Adjustment have not been completed. Forward recognition camera

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Axis Adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)



PROCEDURE

1.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Check if the stored DTCs are current DTCs.


b.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Trouble Codes
50001 386

Result:
Result Proceed to
Current DTC C1AA8 is output A
Current DTC C1AA9 is output B
History DTC C1AA8 is output C



A

2.CHECK VEHICLE CONDITION

B

11.PERFORM FORWARD RECOGNITION CAMERA OPTICAL AXIS ADJUSTMENT

C

13.CLEAR DTCs
2.CHECK VEHICLE CONDITION
a.

Check the operating conditions of the vehicle.

HINT:

DTC C1AA8 may be stored if the forward recognition camera optical axis is temporarily misaligned due to the vehicle being overloaded.



Result:
Result Proceed to
Vehicle is not overloaded or being towed A
Vehicle is overloaded or being towed B



A

3.CHECK WHEEL ALIGNMENT

B

9.PERFORM FORWARD RECOGNITION CAMERA OPTICAL AXIS ADJUSTMENT
3.CHECK WHEEL ALIGNMENT
a.

Check the front wheel alignment (toe).

Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT

HINT:

DTC C1AA8 may be stored if the forward recognition camera optical axis is misaligned due to incorrect wheel alignment (toe).



Result:
Result Proceed to
Front wheel is misaligned (toe) A
Front wheel is not misaligned (toe) B



A

4.ADJUST WHEEL ALIGNMENT

B

7.CHECK FORWARD RECOGNITION CAMERA INSTALLATION
4.ADJUST WHEEL ALIGNMENT
a.

Adjust the alignment (toe) of the wheels.

Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

5.PERFORM FORWARD RECOGNITION CAMERA OPTICAL AXIS ADJUSTMENT
5.PERFORM FORWARD RECOGNITION CAMERA OPTICAL AXIS ADJUSTMENT
a.

Perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
6.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Clear DTCs
50002 386

b.

Make sure that the DTC detection conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Trouble Codes
50001 386

Result:
Result Proceed to
DTC C1AA8 is not output A
DTC C1AA8 is output B



A

END

B

REPLACE FORWARD RECOGNITION CAMERA

7.CHECK FORWARD RECOGNITION CAMERA INSTALLATION
a.

Check the installation condition of the forward recognition camera.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>INSTALLATION

HINT:

If the forward recognition camera bracket is deformed or misaligned, replace the windshield glass.


OK:

No deformation or misalignment in the forward recognition camera bracket.



Result:
Proceed to
OK
NG



OK

5.PERFORM FORWARD RECOGNITION CAMERA OPTICAL AXIS ADJUSTMENT

NG

8.REPLACE WINDSHIELD GLASS
8.REPLACE WINDSHIELD GLASS
a.

Replace the windshield glass.

Click hereVehicle Exterior>WINDOW / GLASS>WINDSHIELD GLASS>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.PERFORM FORWARD RECOGNITION CAMERA OPTICAL AXIS ADJUSTMENT
9.PERFORM FORWARD RECOGNITION CAMERA OPTICAL AXIS ADJUSTMENT
a.

Return the vehicle to normal operating conditions.


b.

Perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)


Result:
Proceed to
NEXT



NEXT

10.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
10.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Clear DTCs
50002 386

b.

Make sure that the DTC detection conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Trouble Codes
50001 386

Result:
Result Proceed to
DTC C1AA8 is not output A
DTC C1AA8 is output B



A

END

B

3.CHECK WHEEL ALIGNMENT
11.PERFORM FORWARD RECOGNITION CAMERA OPTICAL AXIS ADJUSTMENT
a.

Perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)


Result:
Proceed to
NEXT



NEXT

12.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
12.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Clear DTCs
50002 386

b.

Make sure that the DTC detection conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Trouble Codes
50001 386

Result:
Result Proceed to
DTC C1AA9 is not output A
DTC C1AA9 is output B



A

END

B

REPLACE FORWARD RECOGNITION CAMERA

13.CLEAR DTCs
a.

Check for DTCs related to the forward recognition camera.

HINT:

If only history DTCs are stored, they may have been stored due to a temporarily condition such as overloading of the vehicle, and the system returned to normal when Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust was performed.



b.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Clear DTCs
50002 386

Result:
Proceed to
NEXT



NEXT

END