Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS › 2016.10–2019.09
RM32H0E _59 Vehicle Exterior _060314 WINDOW / GLASS _0298548 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during the windshield glass removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effects/Inoperative when not performed Link
Windshield glass Adjust forward recognition camera Dynamic radar cruise control system (Click here)
Lane departure alert system (w/ Steering Control)
Pre-collision system
Forward recognition camera system
Automatic high beam system

NOTICE:

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, lane departure alert system, pre-crash safety system, forward recognition camera system or automatic high beam system may not operate properly due to a difference in the transmissivity or black ceramic border.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 75534 1.REMOVE WINDSHIELD OUTSIDE MOULDING LH

Hide 75533 2.REMOVE WINDSHIELD OUTSIDE MOULDING RH

HINT:

Use the same procedure as for the LH side.


Hide 85292B 3.REMOVE FRONT WIPER ARM HEAD CAP

Hide 85221B 4.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 85211B 5.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 55708 6.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 87810 7.REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)

Hide 87810 8.REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)

Hide 89941 9.REMOVE RAIN SENSOR (w/ Rain Sensor)

Hide 8646C 10.REMOVE FORWARD RECOGNITION CAMERA (w/ Toyota Safety Sense)

Hide 81260A 11.REMOVE MAP LIGHT ASSEMBLY

Hide 81340 12.REMOVE VANITY LIGHT ASSEMBLY

Hide 62312B 13.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62311B 14.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 62212 15.REMOVE FRONT PILLAR GARNISH ASSEMBLY LH

Hide 62211 16.REMOVE FRONT PILLAR GARNISH ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 74612 17.REMOVE ASSIST GRIP COVER

Hide 74610A 18.REMOVE ASSIST GRIP SUB-ASSEMBLY

Hide 74325 19.REMOVE VISOR BRACKET COVER

Hide 74320 20.REMOVE VISOR ASSEMBLY LH (w/ Vanity Light)

Hide 74310 21.REMOVE VISOR ASSEMBLY RH (w/ Vanity Light)

HINT:

Use the same procedure as for the LH side.


Hide 74320 22.REMOVE VISOR ASSEMBLY LH (w/o Vanity Light)

Hide 74310 23.REMOVE VISOR ASSEMBLY RH (w/o Vanity Light)

HINT:

Use the same procedure as for the LH side.


Hide 63311C 25.SEPARATE ROOF HEADLINING

a.

Slightly lower the front section of the roof headlining so that the windshield glass can be removed.

NOTICE:

Do not damage the roof headlining or vehicle interior.


HINT:

It is not necessary to completely remove the roof headlining.



Hide 863C0 26.REMOVE DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY (w/ Digital Audio Broadcasting Antenna)

Hide 56111 27.REMOVE WINDSHIELD GLASS

a.

w/ Windshield Deicer System:

i.

Disconnect the connector.



b.
B454703C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the area around the installation position of the windshield glass on the vehicle body to prevent it from being scratched.


c.
B431533C03
2.396,1.01 2.854,1.229 true 2.229,1.281 2.677,1.708 true 1.385,0.25 1.688,0.542 false 1.177,0.177 1.49,0.333 0.313,0.156 10 false *1 2.927,1.167 3.24,1.323 0.313,0.156 10 false *2 2.74,1.635 3.052,1.792 0.313,0.156 10 false *a
*1 Windshield Glass
*2 Windshield Outside Moulding
*a Cut


Using a knife, cut off the windshield outside moulding as shown in the illustration.


d.
B454704C01
1.375,1.667 1.375,1 1.375,1 1.646,1 true 1.385,1.24 1.656,1.24 true 1.292,1.667 1.604,1.823 0.313,0.156 10 true *a
*a Matchmark


Place matchmarks on the windshield glass and vehicle body at the locations indicated in the illustration.

HINT:

Matchmarks are not necessary if the windshield glass is not going to be reused.



e.
B454705C01
1.229,0.417 1.75,0.667 1.75,0.667 2.229,0.417 false 1.281,1.438 1.417,1.167 false 1.083,1.833 0.99,1.552 true 1.667,0.708 1.979,0.906 0.313,0.198 10 false *1 1.448,1.021 1.76,1.219 0.313,0.198 10 false *2 1.073,1.885 1.323,2.083 0.25,0.198 10 true *a
*1 Windshield Glass Stopper
*2 Front Window Inner Center Moulding
*a Piano Wire


Pass a piano wire between the vehicle body and windshield glass from the interior.


f.

Tie both wire ends to wooden blocks or similar objects that can serve as handles.


g.

Cut the adhesive by pulling the piano wire around the windshield glass.

NOTICE:
·

When separating the windshield glass, be careful not to damage the paint or interior and exterior ornaments.

·

To prevent the instrument panel safety pad sub-assembly from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and instrument panel safety pad sub-assembly.

·

Do not damage the front window inner center moulding.




h.

Disengage the windshield glass stoppers.

B454706C01
1.583,0.917 1.719,0.76 false 5,0.417 5.313,0.688 true 5.729,0.979 5.313,0.979 5.313,0.979 5.313,0.896 false 5.438,0.979 5.438,0.813 false 5.563,0.969 5.563,0.885 false 0.969,0.125 1.281,0.375 0.313,0.25 12 false *A 4.51,0.125 4.823,0.375 0.313,0.25 12 false *B 1.469,0.927 1.781,1.083 0.313,0.156 10 false *1 4.813,0.323 5.125,0.479 0.313,0.156 10 false *2 5.813,0.875 6.125,1.031 0.313,0.156 10 false *1
*A for 1-piece Type *B for 2-piece Type
*1 No. 1 Windshield Glass Stopper *2 No. 2 Windshield Glass Stopper


NOTICE:
·

The No. 1 windshield glass stoppers and No. 2 windshield glass stoppers are installed to the windshield glass as shown in the illustration. Be careful not to damage the windshield glass when cutting the adhesive.

·

To prevent the windshield glass rom falling when performing this operation, be sure to hold the windshield glass using suction cups.



HINT:

Depending on the vehicle, either 1-piece type or 2-piece type stoppers may be present.



i.

Using suction cups, remove the windshield glass.

NOTICE:
·

Be careful not to drop the windshield glass.

·

Leave as much adhesive on the vehicle body as possible when removing the windshield glass.




Hide 56117A 28.REMOVE WINDOW GLASS ADHESIVE DAM

a.

When reusing the windshield glass:

i.
B454707C01
0.188,0.115 0.521,0.375 0.333,0.26 10 false *a
*a Back Side of Windshield Glass


Using a scraper, remove the window glass adhesive dam.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the window glass adhesive dam with a new one.





Hide 75533G 29.REMOVE WINDSHIELD OUTSIDE MOULDING

a.

When reusing the windshield glass:

i.
B454708C01
0.146,0.167 0.479,0.448 0.333,0.281 10 false *a
*a Back Side of Windshield Glass


Using a scraper, remove the windshield outside moulding.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the windshield outside moulding with a new one.





Hide 56115A 30.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 1-piece Type)

a.

When reusing the windshield glass:

i.
B454709C01
0.146,0.115 0.469,0.396 0.323,0.281 10 false *a
*a Back Side of Windshield Glass


Using a scraper, remove the 2 No. 1 windshield glass stoppers.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the 1-piece type No. 1 windshield glass stoppers with new 2-piece type No. 1 and No. 2 windshield glass stoppers.





Hide 56116C 31.REMOVE NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.

When reusing the windshield glass:

i.
B454710C01
0.146,0.115 0.438,0.365 0.292,0.25 10 false *a
*a Back Side of Windshield Glass


Using a scraper, remove the 2 No. 2 windshield glass stoppers.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the No. 2 windshield glass stoppers with new ones.





Hide 56115A 32.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.
B454711

Remove the 2 No. 1 windshield glass stoppers from the vehicle body.

NOTICE:

Be sure to replace the No. 1 windshield glass stoppers with new ones.



Hide 56153C 33.REMOVE FRONT WINDOW INNER CENTER MOULDING

HINT:

Perform the following procedure only when replacement of a front window inner center moulding is necessary.


a.
B454712C01
1.583,2.5 1.583,2.417 1.583,2.417 2.167,2.417 false 1.833,2.5 1.833,2.417 false 0.156,0.083 0.469,0.417 0.313,0.333 10 false *a 2.219,2.333 2.531,2.49 0.313,0.156 10 false *b
*a Back Side of Windshield Glass
*b Matchmark


Place matchmarks on the windshield glass at the locations indicated in the illustration.


b.

Using a scraper, remove the front window inner center moulding.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the front window inner center moulding with a new one.