When the forward recognition camera is replaced with a new one, the new forward recognition camera attempts to store the vehicle information received from the ECM. If the forward recognition camera cannot store the vehicle information, DTC C1AAD is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1AAD | Vehicle Information Initialization Incomplete | 2 seconds after the ignition switch is turned to ON, the vehicle information from the ECM cannot be stored. | ·
CAN communication system ·
Forward recognition camera ·
ECM |
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera learning.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
The forward recognition camera communicates with the ECM via CAN communication. Confirm that the CAN communication system is functioning normally before proceeding.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / LKA/LDA / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC U0100 is not output | A |
| DTC U0100 is output | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / Front Recognition Camera / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Information (2WD/4WD) | Vehicle information (drivetrain) stored in forward recognition camera | 2WD, 4WD or Unknown | 2WD: for 2WD
4WD: for AWD Unknown: Vehicle information not confirmed |
- |
| Vehicle Information (Conv/HV) | Vehicle information (conventional/hybrid) stored in forward recognition camera | Conv, HV or Unknown | Conv: Conventional
HV: Hybrid vehicle Unknown: Vehicle information not confirmed |
- |
| Tester Display |
|---|
| Vehicle Information (2WD/4WD) |
| Vehicle Information (Conv/HV) |
If "Unknown" is displayed, the ECM cannot send vehicle information or the forward recognition camera cannot store the vehicle information. Check for DTCs, replace the ECM if necessary and recheck for DTCs. If the DTC is output again, replace the forward recognition camera.
If "Unknown" is not displayed, the DTC is stored even though the vehicle information is stored in the forward recognition camera. Replace the forward recognition camera.
| Result | Proceed to |
|---|---|
| "Unknown" is displayed | A |
| "Unknown" is not displayed | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / LKA/LDA / Trouble Codes.
Clear the DTCs.
Make sure that the DTC detection conditions are met.
If the following procedure is not performed, the previously output DTC cannot be detected.
Turn the ignition switch to ON and wait 2 seconds or more.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC C1AAD is output | A |
| DTC C1AAD is not output | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Replace the ECM.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / LKA/LDA / Trouble Codes.
Clear the DTCs.
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Turn the ignition switch to ON and wait 2 seconds or more.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC C1AAD is output | A |
| DTC C1AAD is not output | B |
A
B