Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › WINDSHIELD OUTSIDE MOULDING › 2016.10–2020.08
RM32H0E _59 Vehicle Exterior _060783 EXTERIOR PANELS / TRIM _0298073 WINDSHIELD OUTSIDE MOULDING A

EXTERIOR PANELS / TRIM  WINDSHIELD OUTSIDE MOULDING  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during the windshield outside moulding removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effects/Inoperative when not performed Link
Windshield glass sub-assembly Adjust forward recognition camera Dynamic radar cruise control system (Click here)
Lane departure alert system (w/ Steering Control)
Pre-collision system
Forward recognition camera system
Automatic high beam system

NOTICE:

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, lane departure alert system, pre-crash safety system, forward recognition camera system or automatic high beam system may not operate properly due to a difference in the transmissivity or black ceramic border.


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 75534 1.REMOVE WINDSHIELD OUTSIDE MOULDING

a.
B458723C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the windshield outside moulding.


b.
B458724C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws and clip to disconnect the windshield outside moulding as shown in the illustration.


c.
B458725

Using a moulding remover D, disengage the claws to remove the windshield outside moulding.


Hide 75545B 2.REMOVE NO. 1 WINDSHIELD OUTSIDE MOULDING CLIP

HINT:

Perform the following procedure only when replacement of a No. 1 windshield outside moulding clip is necessary.


a.
B458726C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the 5 No. 1 windshield outside moulding clips as shown in the illustration.


Hide 75547C 3.REMOVE NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP

HINT:

Perform the following procedure only when replacement of a No. 3 windshield outside moulding clip is necessary.


a.

Remove the windshield glass sub-assembly.

Click hereVehicle Exterior>WINDOW / GLASS>WINDSHIELD GLASS>REMOVAL


b.

Insert a 4.0 mm (0.157 in.) drill bit into a drill.


c.
B360296C05
0.542,0.906 0.833,1.219 false 0.875,1.156 1.188,1.313 0.313,0.156 10 false *a 0.333,1.5 0.49,1.698 0.156,0.198 10 false A
*a Tape


Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

Standard Measurement:
Area Measurement
A 5.0 mm (0.197 in.)


NOTICE:

Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



d.
B458727C01
2.052,2.927 2.135,2.708 false 1.958,2.958 2.271,3.156 0.313,0.198 10 false *a
*a Flange


Lightly press the drill bit against the No. 3 windshield outside moulding clips to drill off the No. 3 windshield outside moulding clip flanges, and remove the 5 No. 3 windshield outside moulding clips.

CAUTION:

Be careful of the drilled No. 3 windshield outside moulding clips, as they may be hot.


NOTICE:
·

Make sure to protect both the inside and outside of the vehicle as the No. 3 windshield outside moulding clip shavings will fly about.

·

Pressing the drill too firmly will cause the No. 3 windshield outside moulding clip to turn and result in the No. 3 windshield outside moulding clip not being drilled through.

·

Prying the No. 3 windshield outside moulding clip with the drill may damage the No. 3 windshield outside moulding clip installation hole or drill bit.




e.

Using a vacuum cleaner, remove the No. 3 windshield outside moulding clip fragments and shavings from the drilled areas.