Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM › 2016.10–2019.09
RM32H0E _56 Audio / Visual / Telematics _060052 TELEMATICS _0298115 TELEMATICS SYSTEM C

TELEMATICS  TELEMATICS SYSTEM  B1572  Microphone Error  


DESCRIPTION

This DTC is stored when a microphone signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1572 Microphone Error Current at terminal MCVD exceeds the malfunction threshold for 10 seconds while the ignition switch is ON.
·

Telematics transceiver

·

Map light assembly (Telephone microphone assembly)

·

Wire harness or connector



WIRING DIAGRAM

E342822E13
0.792,0.594 1.406,0.792 0.615,0.198 10 false MACC 0.792,1.052 1.406,1.25 0.615,0.198 10 false MCO+ 0.813,1.542 1.427,1.74 0.615,0.198 10 false MCO- 1.323,0.49 1.635,0.688 0.313,0.198 10 false 9 1.333,0.948 1.646,1.146 0.313,0.198 10 false 8 1.344,1.427 1.656,1.625 0.313,0.198 10 false 7 5.625,0.479 5.938,0.677 0.313,0.198 10 false 33 5.625,0.958 5.938,1.156 0.313,0.198 10 false 34 5.625,1.427 5.938,1.625 0.313,0.198 10 false 35 5.625,1.917 5.938,2.115 0.313,0.198 10 false 32 5.938,0.583 6.552,0.781 0.615,0.198 10 false MCVD 5.948,1.063 6.563,1.26 0.615,0.198 10 false MCI+ 5.958,1.521 6.573,1.719 0.615,0.198 10 false MCI- 5.958,2.021 6.573,2.219 0.615,0.198 10 false SGND 0.156,2.521 0.469,2.719 0.313,0.198 10 false R2 0.156,2.677 2.125,3.125 1.969,0.448 10 false Map Light Assembly (Telephone Microphone Assembly) 5.875,2.531 6.448,2.75 0.573,0.219 10 false F51 5.885,2.719 6.604,3.073 0.719,0.354 10 false Telematics Transceiver

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>REGISTRATION


PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 10 seconds.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT TELEMATICS TRANSCEIVER
2.INSPECT TELEMATICS TRANSCEIVER
a.
B235166C63
1.458,0.125 1.875,0.375 0.417,0.25 0.917,1.656 1.292,1.281 true 1.313,1.833 1.458,1.281 true 0.104,0.094 0.375,0.354 0.271,0.26 10 false *a 0.938,1.854 1.427,2.021 0.49,0.167 10 false MCVD 0.615,1.646 1.104,1.854 0.49,0.208 10 false MCI- 1.552,0.167 1.865,0.365 0.313,0.198 10 false F51
*a Component with harness connected
(Telematics Transceiver)


Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F51-33 (MCVD) - Body ground Ignition switch ACC 4 to 6 V


Standard Resistance:
Tester Connection Condition Specified Condition
F51-35 (MCI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - TELEPHONE MICROPHONE ASSEMBLY)

NG

4.REPLACE TELEMATICS TRANSCEIVER
3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - TELEPHONE MICROPHONE ASSEMBLY)
a.

Disconnect the F51 telematics transceiver connector.


b.

Disconnect the R2 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F51-33 (MCVD) - R2-9 (MACC) Always Below 1 Ω
F51-34 (MCI+) - R2-8 (MCO+) Always Below 1 Ω
F51-35 (MCI-) - R2-7 (MCO-) Always Below 1 Ω
F51-33 (MCVD) or R2-9 (MACC) - Body ground Always 10 kΩ or higher
F51-34 (MCI+) or R2-8 (MCO+) - Body ground Always 10 kΩ or higher
F51-35 (MCI-) or R2-7 (MCO-) - Body ground Always 10 kΩ or higher
F51-32 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAP LAMP ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT