Home › Drivetrain › GF1A (TRANSFER / 4WD / AWD) › DYNAMIC TORQUE CONTROL AWD SYSTEM › 2016.10–2019.09
RM32H0E _52 Drivetrain _059725 GF1A TRANSFER / 4WD / AWD _0298220 DYNAMIC TORQUE CONTROL AWD SYSTEM C

GF1A TRANSFER / 4WD / AWD  DYNAMIC TORQUE CONTROL AWD SYSTEM  C1298/98  Linear Solenoid Circuit  


DESCRIPTION

The 4WD ECU assembly receives signals from each sensor to control clutch fluid pressure for limiting the center differential operation, which distributes torque according to the driving conditions.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1298/98 Linear Solenoid Circuit When all of the following continue for 1 second or more:
·

IG1 voltage is 9.5 V or more.

·

The current requested by the 4WD linear solenoid (transmission coupling assembly) is either 0 A or greater than 0.8 A.

·

Open or short occurs in the linear solenoid circuit.


·

Wire harness and connector

·

4WD linear solenoid (Transmission coupling assembly)

·

4WD ECU assembly



WIRING DIAGRAM

C279204E10
1.135,1.531 2.5,1.708 1.365,0.177 10 false 4WD Linear Solenoid 3.656,0.531 3.979,0.74 0.323,0.208 10 false SLC 3.667,1.052 4.021,1.229 0.354,0.177 10 false BSF 4.063,0.531 4.25,0.698 0.188,0.167 10 false 2 4.052,1.031 4.208,1.229 0.156,0.198 10 false 1 4.875,0.563 5.031,0.76 0.156,0.198 10 false 1 4.875,1.031 5.031,1.229 0.156,0.198 10 false 2 5.104,0.667 5.719,0.865 0.615,0.198 10 false SLC- 5.115,1.156 5.729,1.354 0.615,0.198 10 false SLC+ 4.875,2.167 5.333,2.365 0.458,0.198 10 false M77 4.896,2.344 6.354,2.542 1.458,0.198 10 false 4WD ECU Assembly 0.615,2.208 0.927,2.406 0.313,0.198 10 false Q1 0.615,2.385 3.646,2.594 3.031,0.208 10 false Transmission Coupling Assembly

CAUTION / NOTICE / HINT

HINT:

Check the condition of each related circuit connector before troubleshooting.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4WD ECU ASSEMBLY - TRANSMISSION COUPLING ASSEMBLY)
a.
C270074C63
2.417,0.083 2.917,0.333 0.5,0.25 1.417,1.917 1.25,1.917 1.25,1.917 1.094,1.167 true 0.5,1.917 0.667,1.917 0.667,1.917 0.75,1.167 false 1.49,1.833 1.979,2.021 0.49,0.188 10 false SLC+ 2.542,0.104 2.854,0.302 0.313,0.198 10 false M77 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 0.167,1.833 0.583,2 0.417,0.167 10 false SLC-
*a Front view of wire harness connector
(to 4WD ECU Assembly)


Disconnect the 4WD ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M77-2 (SLC+) - M77-1 (SLC-) 20°C (68°F) 2.2 to 2.6 Ω
M77-2 (SLC+) - Body ground Always 10 kΩ or higher
M77-1 (SLC-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT TRANSMISSION COUPLING ASSEMBLY
2.INSPECT TRANSMISSION COUPLING ASSEMBLY
a.
C131916C01
1.575,1.186 1.117,1.614 false 1.813,1.187 2.229,1.591 false 0.844,1.626 1.149,1.778 0.306,0.152 10 SLC 2.161,1.634 2.466,1.786 0.306,0.152 10 BSF 0,0 0.313,0.156 0.313,0.156 10 *a
*a Component without harness connected
(4WD Linear Solenoid (Transmission Coupling Assembly))


Disconnect the Q1 4WD linear solenoid (transmission coupling assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (BSF) - 2 (SLC) 20°C (68°F) 2.2 to 2.6 Ω
1 (BSF) - Body ground Always 10 kΩ or higher
2 (SLC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

REPLACE TRANSMISSION COUPLING ASSEMBLY