Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/ Simple Intelligent Parking Assist System) › 2016.10–2019.09
RM32H0E _56 Audio / Visual / Telematics _060571 PARK ASSIST / MONITORING _0298265 TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/ Simple Intelligent Parking Assist System) J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/ Simple Intelligent Parking Assist System)  Clearance Warning ECU Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the clearance warning ECU assembly.

WIRING DIAGRAM

E267070E02
3.521,1.115 3.833,1.313 0.313,0.198 10 false 3 3.156,1.219 3.771,1.417 0.615,0.198 10 false IG41 5.26,0.354 5.573,0.552 0.313,0.198 10 false 8 5.458,0.469 5.771,0.667 0.313,0.198 10 false IG 5.219,1.583 5.677,1.781 0.458,0.198 10 false F38 2.51,1.583 2.969,1.781 0.458,0.198 10 false F77 2.604,0.677 3.625,0.896 1.021,0.219 10 false ECU-IG1 NO. 4 0.469,0.469 1.99,0.917 1.521,0.448 10 false from IG1-NO. 1 Relay*1 2.531,1.76 3.604,2.125 1.073,0.365 10 false Engine Stop and Start ECU 5.208,1.75 6.792,2.25 1.583,0.5 10 false Clearance Warning ECU Assembly 5.448,1.219 5.604,1.417 0.156,0.198 10 false E 5.271,1.115 5.583,1.313 0.313,0.198 10 false 1 0.229,2.063 2.417,2.396 2.188,0.333 10 false *1: w/o Stop and Start System 0.24,2.417 2.104,2.75 1.865,0.333 10 false *2: w/ Stop and Start System 3.719,0.333 3.958,0.552 0.24,0.219 10 false *1 4.188,0.74 4.427,0.958 0.24,0.219 10 false *2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY POWER SOURCE, BODY GROUND)
a.

Disconnect the clearance warning ECU assembly connector.


b.
E360127C01
1.5,0.188 1.938,0.469 0.438,0.281 0.781,1.583 1.177,1.198 true 2.781,1.625 2.271,1.177 true 1.594,0.24 2.052,0.438 0.458,0.198 10 false F38 0.698,1.625 1.156,1.823 0.458,0.198 10 false E 2.771,1.677 3.229,1.875 0.458,0.198 10 false IG 0.115,0.115 0.573,0.313 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-1 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F38-8 (IG) - F38-1 (E) Ignition switch ON 11 to 14 V*1
10.5 to 16 V*2


*1: w/o Stop and Start System

*2: w/ Stop and Start System



Result:
Result Proceed to
OK A
NG (w/o Stop and Start System) B
NG (w/ Stop and Start System) C



A

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C