Home › Brake › BRAKE (REAR) › REAR BRAKE › 2016.10–2018.05
RM32H0E _54 Brake _060042 BRAKE (REAR) _0298571 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 2.PERFORM REAR BRAKE PAD REPLACEMENT MODE

Hide 3.REMOVE REAR WHEEL

Hide 4.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 47319F 5.SEPARATE REAR FLEXIBLE HOSE

a.
C365999

Remove the union bolt and gasket, and disconnect the rear flexible hose from the rear disc brake cylinder assembly.


Hide 890C0A 6.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

a.
C366000

Disconnect the No. 2 parking brake wire assembly from the parking brake actuator assembly.

NOTICE:
·

Remove any dirt or foreign matter on and around the connector before performing this work.

·

Do not allow water, oil or dirt to enter the No. 2 parking brake wire assembly connector.




Hide 46310B 7.REMOVE PARKING BRAKE ACTUATOR ASSEMBLY

a.
C366001

Using a 5 mm hexagon socket wrench, remove the 2 bolts and parking brake actuator assembly from the rear disc brake cylinder assembly.

NOTICE:
·

Check that there are no brake fluid leaks from the back of the rear disc brake cylinder assembly.

·

If there are any brake fluid leaks, replace the rear disc brake cylinder assembly.




b.

Remove the O-ring from the rear disc brake cylinder assembly.


Hide 8.REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY

a.
C366002C01
1.646,2.771 1.958,2.927 0.313,0.156 10 false *a 0.844,2.917 1.156,3.073 0.313,0.156 10 false *b
*a Turn
*b Hold


Hold the 2 rear disc brake cylinder slide pins and remove the 2 bolts and rear disc brake cylinder assembly.


Hide 9.REMOVE REAR DISC BRAKE PAD

a.
C366003

Remove the 2 rear disc brake pads from the rear disc brake cylinder mounting.


Hide 10.REMOVE REAR DISC BRAKE ANTI-SQUEAL SHIM KIT

Hide 11.REMOVE REAR DISC BRAKE PAD SUPPORT PLATE

a.
C366005

Remove the 4 rear disc brake pad support plates from the rear disc brake cylinder mounting.

NOTICE:

Each rear disc brake pad support plate has a different shape. Be sure to put an identification mark on each rear disc brake pad support plate so that it can be reinstalled to its original position.



Hide 12.REMOVE REAR DISC BRAKE CYLINDER SLIDE PIN

a.
C366006C01
1.792,0.313 2.125,0.313 true 1.583,1.052 1.917,1.052 true 1.958,0.979 2.167,1.156 0.208,0.177 10 true *1 2.167,0.229 2.365,0.417 0.198,0.188 10 true *2
*1 Rear No. 1 Disc Brake Cylinder Slide Pin
*2 Rear No. 2 Disc Brake Cylinder Slide Pin


Remove the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin from the rear disc brake cylinder mounting.


b.
C366007C01
2.208,1.208 2.5,0.917 true 2.521,0.813 2.833,0.969 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the rear disc brake cylinder slide bushing from the rear No. 2 disc brake cylinder slide pin.

NOTICE:

Do not damage the rear No. 2 disc brake cylinder slide pin.



Hide 13.REMOVE REAR DISC BRAKE BUSHING DUST BOOT

a.
C366008

Remove the 2 rear disc brake bushing dust boots from the rear disc brake cylinder mounting.


Hide 14.REMOVE REAR DISC BRAKE CYLINDER MOUNTING

a.
C366009

Remove the 2 bolts and rear disc brake cylinder mounting from the rear axle carrier sub-assembly.


Hide 42431 15.REMOVE REAR DISC

a.
C366010C01
0.99,1.927 1.51,1.5 true 0.979,1.927 1.49,1.448 true 0.823,1.854 1.135,2.01 0.313,0.156 10 false *a
*a Matchmark


Put matchmarks on the rear disc and rear axle hub and bearing assembly.


b.

Remove the rear disc from the rear axle hub and bearing assembly.