Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL (for LHD) › 2016.10–2019.09
RM32H0E _54 Brake _060040 BRAKE SYSTEM (OTHER) _0298586 BRAKE PEDAL(for LHD) N

BRAKE SYSTEM (OTHER)  BRAKE PEDAL(for LHD)  ADJUSTMENT  


PROCEDURE

Hide 1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT

a.

Remove the No. 1 air duct.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


b.

Check the brake pedal height.

NOTICE:
·

Inspect and adjust the brake pedal height with the floor carpet folded back.

·

When performing the measurement, make sure that the measuring device is contacting the surface of the dash panel insulator assembly clip.



i.

Measure the shortest distance between the brake pedal pad surface and dash panel insulator assembly clip.

C366048C01
2.458,2.063 2.76,1.75 true 5.542,2.427 5.875,2.26 true 1.875,1.583 2.177,1.271 true 1.719,1.604 1.99,1.813 0.271,0.208 10 true *1 3.906,1.333 4.219,1.49 0.313,0.156 10 false *a 2.292,2.104 2.552,2.302 0.26,0.198 10 true *2 6.031,1.615 6.344,1.771 0.313,0.156 10 false *a 5.365,2.396 5.625,2.594 0.26,0.198 10 false *2
*1 Brake Pedal Pad *2 Dash Panel Insulator Assembly Clip
*a Brake Pedal Height - -


Brake Pedal Height from Dash Panel Insulator Assembly Clip:

176.0 to 188.0 mm (6.93 to 7.40 in.)


If the pedal height is not as specified, adjust the brake pedal height according to the procedure below.



c.

Adjust the brake pedal height.

i.
C368090C01
2.406,1.115 2.729,0.99 false 1.542,1.969 1.76,1.677 false 1.25,3.865 1.813,3.719 true 2.792,0.896 3.104,1.052 0.313,0.156 10 false *1 1.417,2 1.729,2.156 0.313,0.156 10 false *2 2.573,3.729 2.885,3.885 0.313,0.156 10 false *a 1.073,3.802 1.385,3.958 0.313,0.156 10 false *3
*1 Stop Light Switch Assembly
*2 Clevis Lock Nut
*3 Dash Panel Insulator Assembly Clip
*a Brake Pedal Height


Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


ii.

Loosen the clevis lock nut.


iii.

Adjust the brake pedal height by turning the push rod.

Brake Pedal Height from Dash Panel Insulator Assembly Clip:

176.0 to 188.0 mm (6.93 to 7.40 in.)



iv.

Tighten the clevis lock nut.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


v.

Install the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION



d.

Hide 2.INSPECT BRAKE PEDAL FREE PLAY

a.
C132708C04
2.177,1.542 2.781,1.885 0.604,0.344 10 *a
*a Brake Pedal Free Play


Depress the brake pedal until a slight resistance is felt. Measure the brake pedal free play as shown in the illustration.

Brake Pedal Free Play:

1.0 to 6.0 mm (0.0394 to 0.236 in.)


If the pedal free play is not as specified, check the stop light switch clearance.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION

If the pedal free play is as specified, proceed to the Inspect Brake Pedal Reserve Distance procedure.


Hide 3.INSPECT BRAKE PEDAL RESERVE DISTANCE

a.

With the engine running, depress the brake pedal and measure the brake pedal reserve distance as shown in the illustration.

C368078C01
2.021,1.875 2.021,1.531 true 5.938,2.125 5.604,2.24 false 5.354,2.052 4.99,2.198 true 1.948,1.896 2.156,2.104 0.208,0.208 10 true *1 3.708,1.625 3.927,1.833 0.219,0.208 10 true *a 5.979,2.031 6.292,2.188 0.313,0.156 10 false *b 0.917,1.115 1.146,1.333 0.229,0.219 10 true *c 4.792,2.146 5.063,2.406 0.271,0.26 10 false *d 5.448,1.635 5.667,1.844 0.219,0.208 10 true *a
*1 Brake Pedal Pad - -
*a Brake Pedal Reserve Distance *b Floor Panel
*c 30 mm (1.18 in.) *d Line Extended from Floor Panel Surface


Brake Pedal Reserve Distance from Line Extended from Floor Panel Surface at 300 N (31 kgf, 67.4 lbf):

115.0 mm (4.53 in.) or more


If the distance is not as specified, troubleshoot the brake system.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE