Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2016.10–2019.09
RM32H0E _57 Power Source / Network _059621 NETWORKING _0298704 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Skid Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Skid Control ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Skid Control (ABS/VSC/TRC)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Skid Control (ABS/VSC/TRC)" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Skid Control (ABS/VSC/TRC)" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Skid Control ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Brake actuator assembly branch line or connector

·

Power source circuit of brake actuator assembly

·

Brake actuator assembly ground circuit

·

Brake actuator assembly



WIRING DIAGRAM

for LHD


C366218E03
0.083,1.708 2.208,1.979 2.125,0.271 10 false No. 5 CAN Junction Connector 0.083,1.542 0.542,1.76 0.458,0.219 10 false F124 1.646,0.51 2.104,0.729 0.458,0.219 10 false 5 1.646,1.042 2.104,1.26 0.458,0.219 10 false 16 5.51,1.042 5.969,1.26 0.458,0.219 10 false 19 5.583,0.51 6.042,0.729 0.458,0.219 10 false 5 5.813,0.604 6.417,0.823 0.604,0.219 10 false CANH 5.813,1.146 6.458,1.375 0.646,0.229 10 false CANL 5.813,1.865 6.385,2.115 0.573,0.25 10 false +BM 5.813,2.396 6.427,2.615 0.615,0.219 10 false +BS 5.813,2.938 6.396,3.135 0.583,0.198 10 false IG1 5.813,3.813 6.396,4.052 0.583,0.24 10 false GND1 5.813,4.354 6.552,4.573 0.74,0.219 10 false GND2 5.583,1.76 6.042,1.979 0.458,0.219 10 false 1 5.51,2.302 5.969,2.521 0.458,0.219 10 false 30 5.51,2.823 5.969,3.042 0.458,0.219 10 false 36 5.51,3.719 5.969,3.938 0.458,0.219 10 false 46 5.51,4.26 5.969,4.479 0.458,0.219 10 false 14 5.396,4.74 6.135,4.958 0.74,0.219 10 false A42 5.396,4.906 7.156,5.219 1.76,0.313 10 false Brake Actuator Assembly 4.26,3.083 5.563,3.344 1.302,0.26 10 false ECU-IG1 NO. 2 4.438,2.542 5.313,2.771 0.875,0.229 10 false ABS-MAIN 4.219,2.01 5.479,2.219 1.26,0.208 10 false ABS MTR NO. 1 2.75,1.865 4.01,2.073 1.26,0.208 10 false from Battery 2.75,2.396 4.01,2.604 1.26,0.208 10 false from Battery 2.083,2.938 3.927,3.146 1.844,0.208 10 false from IG1-NO. 1 Relay*1 1.385,3.396 3.646,3.688 2.26,0.292 10 false from Engine Stop and Start ECU*2 5.396,3.125 5.854,3.344 0.458,0.219 10 false *2 5.031,2.833 5.49,3.052 0.458,0.219 10 false *1 0.49,4.417 2.75,4.708 2.26,0.292 10 false *1: w/o Stop and Start System 0.49,4.75 2.75,5.042 2.26,0.292 10 false *2: w/ Stop and Start System


for RHD



C366218E04
0.094,1.719 2.219,1.99 2.125,0.271 10 false No. 5 CAN Junction Connector 0.083,1.542 0.542,1.76 0.458,0.219 10 false F117 1.646,0.51 2.104,0.729 0.458,0.219 10 false 7 1.646,1.042 2.104,1.26 0.458,0.219 10 false 18 5.51,1.042 5.969,1.26 0.458,0.219 10 false 19 5.583,0.51 6.042,0.729 0.458,0.219 10 false 5 5.813,0.604 6.417,0.823 0.604,0.219 10 false CANH 5.813,1.146 6.458,1.375 0.646,0.229 10 false CANL 5.813,1.865 6.385,2.115 0.573,0.25 10 false +BM 5.813,2.396 6.427,2.615 0.615,0.219 10 false +BS 5.813,2.938 6.396,3.135 0.583,0.198 10 false IG1 5.813,3.813 6.396,4.052 0.583,0.24 10 false GND1 5.813,4.354 6.552,4.573 0.74,0.219 10 false GND2 5.583,1.76 6.042,1.979 0.458,0.219 10 false 1 5.51,2.302 5.969,2.521 0.458,0.219 10 false 30 5.51,2.823 5.969,3.042 0.458,0.219 10 false 36 5.51,3.719 5.969,3.938 0.458,0.219 10 false 46 5.51,4.26 5.969,4.479 0.458,0.219 10 false 14 5.396,4.74 6.135,4.958 0.74,0.219 10 false A42 5.396,4.906 7.156,5.219 1.76,0.313 10 false Brake Actuator Assembly 4.26,3.083 5.563,3.344 1.302,0.26 10 false ECU-IG1 NO. 2 4.438,2.542 5.313,2.771 0.875,0.229 10 false ABS-MAIN 4.219,2.01 5.479,2.219 1.26,0.208 10 false ABS MTR NO. 1 2.75,1.865 4.01,2.073 1.26,0.208 10 false from Battery 2.75,2.396 4.01,2.604 1.26,0.208 10 false from Battery 2.083,2.938 3.927,3.146 1.844,0.208 10 false from IG1-NO. 1 Relay*1 1.385,3.396 3.646,3.688 2.26,0.292 10 false from Engine Stop and Start ECU*2 5.396,3.125 5.854,3.344 0.458,0.219 10 false *2 5.031,2.833 5.49,3.052 0.458,0.219 10 false *1 0.49,4.417 2.75,4.708 2.26,0.292 10 false *1: w/o Stop and Start System 0.49,4.75 2.75,5.042 2.26,0.292 10 false *2: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), turn the cruise control main switch on, turn the LDA main switch on and then drive the vehicle at a speed of 5 km/h (3 mph) or more for approximately 20 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK DTC (VEHICLE STABILITY CONTROL SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC/EPB / Trouble Codes.

Chassis > ABS/VSC/TRC/EPB > Trouble Codes
50001 105

e.

Check that DTC C1241 which indicates a malfunction in the power source circuit of the vehicle stability control system is not stored by the vehicle stability control system.


Result:
Result Proceed to
DTC C1241 is not output A
DTC C1241 is output B



A

2.CHECK FOR OPEN IN CAN BUS LINES (BRAKE ACTUATOR ASSEMBLY BRANCH LINE)

B

GO TO DIAGNOSTIC PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN CAN BUS LINES (BRAKE ACTUATOR ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the brake actuator assembly connector.


c.
C366214C01
1.458,0.75 1.958,1 0.5,0.25 0.771,2.708 1.375,1.75 true 2.146,2.708 1.448,1.927 true 0.135,0.073 0.448,0.229 0.313,0.156 10 false *a 0.583,2.719 1.208,2.938 0.625,0.219 10 false CANL 1.99,2.719 2.615,2.938 0.625,0.219 10 false CANH 1.583,0.771 1.896,0.927 0.313,0.156 10 false A42
*a Front view of wire harness connector
(to Brake Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-5 (CANH) - A42-19 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C366214C02
1.458,0.75 1.958,1 0.5,0.25 0.646,1.625 0.385,1.01 true 1.031,2.698 1.49,1.635 true 0.646,1.865 0.385,2.323 true 2.698,1.615 2.979,0.958 true 2.792,1.854 2.896,2.604 true 0.135,0.073 0.448,0.229 0.313,0.156 10 false *a 0.073,0.917 0.698,1.135 0.625,0.219 10 false +BS 0.927,2.698 1.229,2.917 0.302,0.219 10 false IG1 1.583,0.771 1.896,0.927 0.313,0.156 10 false A42 0.188,2.344 0.813,2.563 0.625,0.219 10 false +BM 3.031,0.844 3.427,1.031 0.396,0.188 10 false GND1 2.75,2.615 3.146,2.802 0.396,0.188 10 false GND2
*a Front view of wire harness connector
(to Brake Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-46 (GND1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
A42-14 (GND2) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A42-1 (+BM) - Body ground Always 11 to 14 V
A42-30 (+BS) - Body ground Always 11 to 14 V
A42-36 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (w/o Stop and Start System) C
NG (except IG1 circuit) (w/ Stop and Start System)
NG (for IG1 circuit) (w/ Stop and Start System) D



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

D

GO TO STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)