Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2016.10–2020.08
RM32H0E _57 Power Source / Network _059621 NETWORKING _0298704 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Air Conditioning Amplifier Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Air Conditioning Amplifier Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Air Conditioning Amplifier" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Air Conditioning Amplifier" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Air Conditioning Amplifier" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Air Conditioning Amplifier Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Air conditioning amplifier assembly branch line or connector

·

Power source circuit of air conditioning amplifier assembly

·

Air conditioning amplifier assembly ground circuit

·

Air conditioning amplifier assembly



WIRING DIAGRAM

C366194E02
0.146,1.719 2.115,1.906 1.969,0.188 10 false No. 3 CAN Junction Connector 0.156,1.563 0.635,1.771 0.479,0.208 10 false F114 2.115,2.198 3.01,2.396 0.896,0.198 10 false from Battery 1.563,2.76 3.021,2.969 1.458,0.208 10 false from IG1-NO. 1 Relay 5.146,0.625 5.458,0.781 0.313,0.156 10 false F72 5.479,0.625 5.958,0.833 0.479,0.208 10 false F73 5.146,1.156 5.458,1.313 0.313,0.156 10 false F72 5.135,2.229 5.448,2.385 0.313,0.156 10 false F72 5.146,2.771 5.458,2.927 0.313,0.156 10 false F72 5.135,3.302 5.448,3.458 0.313,0.156 10 false F72 5.469,1.167 5.792,1.375 0.323,0.208 10 false F73 5.458,2.229 5.781,2.438 0.323,0.208 10 false F73 5.469,2.771 5.792,2.979 0.323,0.208 10 false F73 5.469,3.302 5.792,3.51 0.323,0.208 10 false F73 3.719,2.385 4.615,2.583 0.896,0.198 10 false ECU-B NO. 2 3.677,2.927 4.74,3.104 1.063,0.177 10 false ECU-IG1 NO. 4 1.625,0.531 1.854,0.708 0.229,0.177 10 false 4 1.604,1.052 1.833,1.229 0.229,0.177 10 false 15 5.219,0.448 5.448,0.625 0.229,0.177 10 false 9 5.51,0.458 5.74,0.635 0.229,0.177 10 false 11 5.177,0.99 5.406,1.167 0.229,0.177 10 false 10 5.49,1 5.719,1.177 0.229,0.177 10 false 12 5.208,2.063 5.438,2.24 0.229,0.177 10 false 1 5.219,2.615 5.448,2.792 0.229,0.177 10 false 5 5.521,2.073 5.75,2.25 0.229,0.177 10 false 1 5.542,2.615 5.771,2.792 0.229,0.177 10 false 2 5.188,3.146 5.417,3.323 0.229,0.177 10 false 29 5.542,3.146 5.771,3.323 0.229,0.177 10 false 4 5.156,1.354 5.385,1.531 0.229,0.177 10 false *1 5.156,0.802 5.385,0.979 0.229,0.177 10 false *1 5.49,0.813 5.719,0.99 0.229,0.177 10 false *2 5.5,1.354 5.729,1.531 0.229,0.177 10 false *2 5.479,2.406 5.708,2.583 0.229,0.177 10 false *2 5.479,2.948 5.708,3.125 0.229,0.177 10 false *2 5.49,3.479 5.719,3.656 0.229,0.177 10 false *2 5.156,2.406 5.385,2.583 0.229,0.177 10 false *1 5.156,2.938 5.385,3.115 0.229,0.177 10 false *1 5.167,3.479 5.396,3.656 0.229,0.177 10 false *1 5.792,0.635 6.271,0.844 0.479,0.208 10 false CANH 5.792,1.167 6.271,1.375 0.479,0.208 10 false CANL 5.792,2.229 6.271,2.438 0.479,0.208 10 false B 5.781,3.302 6.26,3.51 0.479,0.208 10 false GND 5.781,2.781 6.26,2.99 0.479,0.208 10 false IG+ 5.469,3.708 7.021,4.25 1.552,0.542 10 false Air Conditioning Amplifier Assembly 0.563,3.906 3.958,4.104 3.396,0.198 10 false *1: w/ Top-mounted Air Conditioner Pressure Sensor 0.563,4.281 4.208,4.448 3.646,0.167 10 false *2: w/ Side-mounted Air Conditioner Pressure Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch ON and wait at least approximately 20 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Top-mounted Air Conditioner Pressure Sensor A
w/ Side-mounted Air Conditioner Pressure Sensor B



A

2.CHECK FOR OPEN IN CAN BUS LINES (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH LINE)

B

4.CHECK FOR OPEN IN CAN BUS LINES (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH LINE)
2.CHECK FOR OPEN IN CAN BUS LINES (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the air conditioning amplifier assembly connector.


c.
E281476C43
1.448,0.167 1.948,0.417 0.5,0.25 1.365,1.729 1.469,1.188 true 2.313,1.75 1.656,1.188 true 0.167,0.083 0.479,0.281 0.313,0.198 10 false *a 1.573,0.229 1.885,0.427 0.313,0.198 10 false F72 1.198,1.76 1.635,1.979 0.438,0.219 10 false CANH 2.188,1.781 2.625,2 0.438,0.219 10 false CANL
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F72-9 (CANH) -F72-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
E281476C46
1.448,0.167 1.948,0.417 0.5,0.25 0.635,1.74 0.927,1.198 true 1.76,1.771 1.51,1.365 true 0.24,1.74 0.333,1.167 true 0.167,0.083 0.479,0.281 0.313,0.198 10 false *a 1.594,0.229 1.906,0.427 0.313,0.198 10 false F72 0.573,1.792 0.885,1.99 0.313,0.198 10 false IG+ 1.656,1.813 1.969,2.01 0.313,0.198 10 false GND 0.208,1.781 0.521,1.979 0.313,0.198 10 false B
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F72-29 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F72-1 (B) - Body ground Always 11 to 14 V
F72-5 (IG+) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

4.CHECK FOR OPEN IN CAN BUS LINES (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the air conditioning amplifier assembly connector.


c.
C349836C15
1.5,0.208 1.917,0.479 0.417,0.271 2.031,1.833 2.281,1 true 1.896,1.833 2.167,0.76 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 1.604,0.26 1.917,0.458 0.313,0.198 10 false F73 2.229,0.635 2.896,0.844 0.667,0.208 10 false CANH 2.354,0.896 3.021,1.104 0.667,0.208 10 false CANL
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F73-11 (CANH) -F73-12 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C349836C16
1.5,0.208 1.917,0.479 0.417,0.271 0.781,1.615 0.615,1.031 true 1.146,1.615 1.313,1.031 true 2.656,1.625 2.833,1.083 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 1.604,0.25 1.917,0.448 0.313,0.198 10 false F73 0.479,0.896 0.708,1.104 0.229,0.208 10 false B 1.385,0.865 2.052,1.073 0.667,0.208 10 false IG+ 2.917,0.979 3.292,1.198 0.375,0.219 10 false GND
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F73-4 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F73-1 (B) - Body ground Always 11 to 14 V
F73-2 (IG+) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)