Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2016.10–2019.09
RM32H0E _57 Power Source / Network _059621 NETWORKING _0298704 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Engine Stop and Start ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Engine Stop and Start ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Stop and Go/Start" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Stop and Go/Start" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Stop and Go/Start" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Engine Stop and Start ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Engine stop and start ECU branch line or connector

·

Power source circuit of engine stop and start ECU

·

Engine stop and start ECU ground circuit

·

Engine stop and start ECU



WIRING DIAGRAM

C366197E03
0.156,1.542 0.708,1.74 0.552,0.198 10 false F113 0.156,1.688 2.073,1.927 1.917,0.24 10 false No. 2 CAN Junction Connector 1.646,0.469 1.865,0.667 0.219,0.198 10 false 6 1.625,1.063 1.844,1.26 0.219,0.198 10 false 17 5.469,0.625 5.854,0.823 0.385,0.198 10 false F77 5.458,1.156 5.844,1.354 0.385,0.198 10 false F77 5.458,2.229 5.844,2.427 0.385,0.198 10 false A61 5.448,4.365 5.833,4.563 0.385,0.198 10 false A61 5.802,1.156 6.281,1.354 0.479,0.198 10 false CANL 5.781,0.635 6.271,0.833 0.49,0.198 10 false CANH 5.448,2.771 5.833,2.969 0.385,0.198 10 false F77 5.458,3.302 5.844,3.5 0.385,0.198 10 false F77 5.458,3.833 5.844,4.031 0.385,0.198 10 false F77 5.813,2.219 6.292,2.417 0.479,0.198 10 false BIN1 5.802,2.75 6.281,2.948 0.479,0.198 10 false IG1 5.802,3.302 6.281,3.5 0.479,0.198 10 false IG2 5.792,4.375 6.271,4.573 0.479,0.198 10 false GND1 5.813,3.844 6.292,4.042 0.479,0.198 10 false ACC 5.49,0.448 5.708,0.646 0.219,0.198 10 false 13 5.469,0.979 5.688,1.177 0.219,0.198 10 false 14 5.51,2.052 5.729,2.25 0.219,0.198 10 false 3 5.479,2.583 5.698,2.781 0.219,0.198 10 false 21 5.469,3.115 5.688,3.313 0.219,0.198 10 false 18 5.51,4.177 5.729,4.375 0.219,0.198 10 false 8 5.479,3.656 5.698,3.854 0.219,0.198 10 false 19 2.729,2.208 3.583,2.458 0.854,0.25 10 false from Battery 2.198,2.75 3.688,2.938 1.49,0.188 10 false from IG1-NO. 1 Relay 2.188,3.281 3.677,3.469 1.49,0.188 10 false from IG2-NO. 2 Relay 2.521,3.823 4.01,4.01 1.49,0.188 10 false from ACC Relay 4.323,2.375 5.177,2.625 0.854,0.25 10 false BBC NO. 1 4.177,3.438 5.208,3.677 1.031,0.24 10 false ECU-IG2 NO. 3 4.146,2.906 5.292,3.146 1.146,0.24 10 false ECU-IG1 NO. 2 4.375,3.99 5.229,4.24 0.854,0.25 10 false ECU-ACC 5.313,4.771 7.094,5.021 1.781,0.25 10 false Engine Stop and Start ECU

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch ON and wait at least approximately 20 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (ENGINE STOP AND START ECU BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C298836C25
1.563,0.104 1.979,0.396 0.417,0.292 0.75,1.458 0.521,1.854 true 0.885,1.448 1.188,1.833 true 1.646,0.156 2.198,0.406 0.552,0.25 10 false F77 0.073,0.083 0.385,0.281 0.313,0.198 10 false *a 1.104,1.885 1.719,2.083 0.615,0.198 10 false CANL 0.281,1.896 0.896,2.094 0.615,0.198 10 false CANH
*a Front view of wire harness connector
(to Engine Stop and Start ECU)


Disconnect the engine stop and start ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-13 (CANH) - F77-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (ENGINE STOP AND START ECU)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the engine stop and start ECU connector.


b.
C323601C26
1.51,0.177 1.938,0.448 0.427,0.271 1.531,2.052 1.958,2.323 0.427,0.271 0.646,1.604 1.146,1.354 true 1.76,4.063 1.542,3.51 true 0.885,4.083 1.385,3.51 true 2.51,4.031 2.167,3.5 true 2.833,1.625 2.417,1.396 true 0.115,0.052 0.427,0.25 0.313,0.198 10 false *a 1.594,0.24 2.052,0.438 0.458,0.198 10 false A61 0.323,1.552 0.781,1.75 0.458,0.198 10 false BIN1 1.625,2.115 2.083,2.313 0.458,0.198 10 false F77 1.646,4.115 2.104,4.313 0.458,0.198 10 false ACC 0.792,4.125 1.25,4.323 0.458,0.198 10 false IG2 2.458,4.073 2.917,4.271 0.458,0.198 10 false IG1 2.885,1.583 3.354,1.75 0.469,0.167 10 false GND1
*a Front view of wire harness connector
(to Engine Stop and Start ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A61-8 (GND1) -Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A61-3 (BIN1) - Body ground Always 11 to 14 V
F77-18 (IG2) - Body ground Ignition switch ON 11 to 14 V
F77-19 (ACC) - Body ground Ignition switch ACC 11 to 14 V
F77-21 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)