Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2016.10–2020.08
RM32H0E _57 Power Source / Network _059621 NETWORKING _0298704 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  DCM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
DCM Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "DCM" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "DCM" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "DCM" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "DCM Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Telematics transceiver branch line or connector

·

Power source circuit of telematics transceiver

·

Telematics transceiver ground circuit

·

Telematics transceiver



WIRING DIAGRAM

C366199E03
0.115,1.729 2.094,1.927 1.979,0.198 10 false No. 3 CAN Junction Connector 2.74,2.177 3.594,2.417 0.854,0.24 10 false from Battery 2.146,2.729 3.573,2.979 1.427,0.25 10 false from IG2-NO. 2 Relay 2.469,3.281 3.625,3.552 1.156,0.271 10 false from ACC Relay 4.281,2.385 5.344,2.604 1.063,0.219 10 false DCM/MAYDAY 4.313,2.906 5.375,3.125 1.063,0.219 10 false ECU-IG2 NO. 3 4.531,3.438 5.594,3.656 1.063,0.219 10 false ECU-ACC 5.792,0.604 6.333,0.802 0.542,0.198 10 false CANP 5.802,1.146 6.344,1.344 0.542,0.198 10 false CANN 5.792,2.198 6.333,2.396 0.542,0.198 10 false +B 5.802,2.729 6.344,2.927 0.542,0.198 10 false IG2 5.802,3.292 6.344,3.49 0.542,0.198 10 false ACC 5.802,3.823 6.042,4.042 0.24,0.219 10 false E 5.5,4.219 6.042,4.417 0.542,0.198 10 false F51 5.479,4.375 7.01,4.615 1.531,0.24 10 false Telematics Transceiver 5.542,0.51 5.813,0.698 0.271,0.188 10 false 15 5.531,1.063 5.802,1.25 0.271,0.188 10 false 16 5.573,2.115 5.844,2.302 0.271,0.188 10 false 1 5.583,2.646 5.854,2.833 0.271,0.188 10 false 7 5.573,3.188 5.844,3.375 0.271,0.188 10 false 8 5.583,3.74 5.854,3.927 0.271,0.188 10 false 4 0.115,1.563 0.656,1.76 0.542,0.198 10 false F114 1.625,1.063 1.896,1.25 0.271,0.188 10 false 19 1.635,0.51 1.906,0.698 0.271,0.188 10 false 8

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch ON and wait for at least approximately 12 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (TELEMATICS TRANSCEIVER BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the telematics transceiver connector.


c.
C285245C27
1.5,0.083 2,0.333 0.5,0.25 1.823,1.208 1.167,1.917 true 2.031,1.219 2.542,1.927 true 0.052,0.042 0.385,0.302 0.333,0.26 10 false *a 2.615,1.854 3.229,2.052 0.615,0.198 10 false CANN 0.719,1.823 1.333,2.021 0.615,0.198 10 false CANP 1.615,0.115 2.083,0.365 0.469,0.25 10 false F51
*a Front view of wire harness connector
(to Telematics Transceiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F51-15 (CANP) - F51-16 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (TELEMATICS TRANSCEIVER)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C285245C28
1.5,0.083 2,0.333 0.5,0.25 0.74,0.26 0.427,0.885 true 2.375,0.896 2.792,0.25 true 0.396,1.208 0.25,1.865 true 0.594,1.208 0.885,1.865 true 0.052,0.042 0.385,0.302 0.333,0.26 10 false *a 2.865,0.146 3.104,0.344 0.24,0.198 10 false E 0.75,1.885 1.365,2.083 0.615,0.198 10 false ACC 1.615,0.115 2.083,0.365 0.469,0.25 10 false F51 0.781,0.177 1.396,0.375 0.615,0.198 10 false +B 0.135,1.906 0.75,2.104 0.615,0.198 10 false IG2
*a Front view of wire harness connector
(to Telematics Transceiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F51-4 (E) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F51-1 (+B) - Body ground Always 11 to 14 V
F51-7 (IG2) - Body ground Ignition switch ON 11 to 14 V
F51-8 (ACC) - Body ground Ignition switch ACC 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)