Home › Engine / Hybrid System › CRUISE CONTROL › ROAD SIGN ASSIST SYSTEM › 2016.10–2020.08
RM32H0E _51 Engine / Hybrid System _059516 CRUISE CONTROL _0292294 ROAD SIGN ASSIST SYSTEM C

CRUISE CONTROL  ROAD SIGN ASSIST SYSTEM  C1AA8  Front Camera Module Incorrect Axial Gap  C1AA9  Front Camera Module Beam Axis Not Adjusted  


DESCRIPTION

If the forward recognition camera detects that the forward recognition camera axis has deviated, DTC C1AA8 is stored. Also, if Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust is not performed after installing the forward recognition camera, DTC C1AA9 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AA8 Front Camera Module Incorrect Axial Gap While the ignition switch is ON and the road sign assist system is operating, the forward recognition camera detects forward recognition camera optical axis deviation.
·

Forward recognition camera

·

Windshield glass


C1AA9 Front Camera Module Beam Axis Not Adjusted While the ignition switch is ON, the forward recognition camera detects that forward recognition camera adjustment has not been completed. Forward recognition camera

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)



PROCEDURE

1.CHECK FOR DTCs (ROAD SIGN ASSIST SYSTEM)
a.

Check if the stored DTCs are current DTCs.


b.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > Road Sign Assist > Trouble Codes
50001 387

Result:
Result Proceed to
Current DTC C1AA8 is output A
Current DTC C1AA9 is output B
History DTC C1AA8 is output C



A

2.CHECK VEHICLE CONDITION

B

11.PERFORM FORWARD RECOGNITION CAMERA OPTICAL AXIS LEARNING

C

13.CLEAR DTCs
2.CHECK VEHICLE CONDITION
a.

Check the operating conditions of the vehicle.

HINT:

DTC C1AA8 may be stored if the forward recognition camera optical axis is temporarily misaligned due to the vehicle being overloaded.



Result:
Result Proceed to
Vehicle is not overloaded or being towed A
Vehicle is overloaded or being towed B



A

3.CHECK WHEEL ALIGNMENT

B

9.PERFORM FORWARD RECOGNITION CAMERA OPTICAL AXIS LEARNING
3.CHECK WHEEL ALIGNMENT
a.

Check the front and rear wheel alignment (toe).

for Front Side: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT

for Rear Side: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>REAR WHEEL ALIGNMENT>ADJUSTMENT

HINT:

DTC C1AA8 may be stored if the forward recognition camera optical axis is misaligned due to incorrect wheel alignment (toe).



Result:
Result Proceed to
Front or rear wheel is misaligned (toe) A
Front and rear wheels are not misaligned (toe) B



A

4.ADJUST WHEEL ALIGNMENT

B

7.CHECK FORWARD RECOGNITION CAMERA INSTALLATION
4.ADJUST WHEEL ALIGNMENT
a.

Result:
Proceed to
NEXT



NEXT

5.PERFORM FORWARD RECOGNITION CAMERA OPTICAL AXIS LEARNING
5.PERFORM FORWARD RECOGNITION CAMERA OPTICAL AXIS LEARNING
a.

Perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTCs (ROAD SIGN ASSIST SYSTEM)
6.CHECK FOR DTCs (ROAD SIGN ASSIST SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > Road Sign Assist > Clear DTCs
50002 387

b.

Make sure that the following conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > Road Sign Assist > Trouble Codes
50001 387

Result:
Result Proceed to
DTC C1AA8 is not output A
DTC C1AA8 is output B



A

END

B

REPLACE FORWARD RECOGNITION CAMERA

7.CHECK FORWARD RECOGNITION CAMERA INSTALLATION
a.

Check the installation condition of the forward recognition camera.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>INSTALLATION

HINT:

If the forward recognition camera bracket is deformed or misaligned, replace the windshield glass.


OK:

No deformation or misalignment in the forward recognition camera bracket.



Result:
Proceed to
OK
NG



OK

5.PERFORM FORWARD RECOGNITION CAMERA OPTICAL AXIS LEARNING

NG

8.REPLACE WINDSHIELD GLASS
8.REPLACE WINDSHIELD GLASS
a.

Replace the windshield glass.

Click hereVehicle Exterior>WINDOW / GLASS>WINDSHIELD GLASS>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.PERFORM FORWARD RECOGNITION CAMERA OPTICAL AXIS LEARNING
9.PERFORM FORWARD RECOGNITION CAMERA OPTICAL AXIS LEARNING
a.

Return the vehicle to normal operating conditions.


b.

Perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)


Result:
Proceed to
NEXT



NEXT

10.CHECK FOR DTCs (ROAD SIGN ASSIST SYSTEM)
10.CHECK FOR DTCs (ROAD SIGN ASSIST SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > Road Sign Assist > Clear DTCs
50002 387

b.

Make sure that the following conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > Road Sign Assist > Trouble Codes
50001 387

Result:
Result Proceed to
DTC C1AA8 is not output A
DTC C1AA8 is output B



A

END

B

3.CHECK WHEEL ALIGNMENT
11.PERFORM FORWARD RECOGNITION CAMERA OPTICAL AXIS LEARNING
a.

Perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)


Result:
Proceed to
NEXT



NEXT

12.CHECK FOR DTCs (ROAD SIGN ASSIST SYSTEM)
12.CHECK FOR DTCs (ROAD SIGN ASSIST SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > Road Sign Assist > Clear DTCs
50002 387

b.

Make sure that the following conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > Road Sign Assist > Trouble Codes
50001 387

Result:
Result Proceed to
DTC C1AA9 is not output A
DTC C1AA9 is output B



A

END

B

REPLACE FORWARD RECOGNITION CAMERA

13.CLEAR DTCs
a.

Check for DTCs related to the forward recognition camera.

HINT:

If only history DTCs are stored, they may have been stored due to a temporarily condition such as overloading of the vehicle, and the system returned to normal when Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust was performed.



b.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > Road Sign Assist > Clear DTCs
50002 387

Result:
Proceed to
NEXT



NEXT

END