Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM (w/ Entry and Start System)
RM32H0E _58 Vehicle Interior _060784 THEFT DETERRENT / KEYLESS ENTRY _0299015 IMMOBILISER SYSTEM(w/ Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Entry and Start System)  Immobiliser System does not Operate Properly  


DESCRIPTION

The immobiliser system compares the ID code that is registered to the certification ECU (smart key ECU assembly) with the ID code of the transponder chip that is embedded in the electrical key transmitter sub-assembly.

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the ECM or ID code box (immobiliser code ECU), refer to Service Bulletin.

·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

If an immobiliser system or SFI system DTC is output, first perform troubleshooting for the immobiliser system or SFI system DTC.


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM (w/ Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.CHECK WHETHER ENGINE STARTS

B

2.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts 5 seconds after the engine switch turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
3.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
a.

Disconnect the F21 ID code box (immobiliser code ECU) connector.


b.

Disconnect the A38 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F21-3 (EFII) - A38-45 (IMO) Always Below 1 Ω
F21-4 (EFIO) - A38-28 (IMI) Always Below 1 Ω
F21-3 (EFII) or A38-45 (IMO) - Body ground Always 10 kΩ or higher
F21-4 (EFIO) or A38-28 (IMI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REGISTER ECU COMMUNICATION ID

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID code.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER ENGINE STARTS
5.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

6.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
6.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

7.REGISTER ECU COMMUNICATION ID
7.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID code.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER ENGINE STARTS
8.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts.

OK:

Engine starts normally.



Result:
Result Proceed to
OK A
NG (for 8NR-FTS) B
NG (for 3ZR-FAE) C



A

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

B

C