Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM (w/ Entry and Start System)
RM32H0E _58 Vehicle Interior _060784 THEFT DETERRENT / KEYLESS ENTRY _0299015 IMMOBILISER SYSTEM(w/ Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Entry and Start System)  B2799  Engine Immobiliser System Malfunction  B279986  Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid  


DESCRIPTION

If there is a communication malfunction between the ECM and ID code box (immobiliser code ECU), or when the communication ID codes do not match, the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2799 Engine Immobiliser System Malfunction Either condition is met (1 trip detection logic*):
·

A malfunction in the communication between the ECM and ID code box (immobiliser code ECU).

·

A malfunction in the communication lines between the ECM and ID code box (immobiliser code ECU).

·

A matching communication code cannot be verified during communication between the ECM and ID code box (immobiliser code ECU).


·

ID code box (immobiliser code ECU)

·

ECM

·

Wire harness or connector


DTC output confirmation operation (Perform either of the following):
·

Start the engine and wait for 10 seconds. If there is a malfunction, the engine will stop (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds).

·

Connect the cable to the negative (-) battery terminal, start the engine and wait for 10 seconds (communication begins within 3 seconds of the engine switch being turned on (IG), and DTCs are stored after 6 seconds).


B279986 Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid Either of the following conditions is met (1 trip detection logic*):
·

A malfunction in the communication between the ECM and ID code box (immobiliser code ECU).

·

A malfunction in the communication lines between the ECM and ID code box (immobiliser code ECU).

·

A matching communication code cannot be verified during communication between the ECM and ID code box (immobiliser code ECU).


·

ID code box (immobiliser code ECU)

·

ECM

·

Wire harness or connector


DTC output confirmation operation (Perform either of the following):
·

Start the engine and wait for 10 seconds. If there is a malfunction, the engine will stop (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds).

·

Connect the cable to the negative (-) battery terminal, start the engine and wait for 10 seconds (communication begins within 3 seconds of the engine switch being turned on (IG), and DTCs are stored after 6 seconds).



*: Only output while a malfunction is present.


DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition Engine start operation. ○ ○ ○
Malfunction Status A malfunction in the communication between the ECM and ID code box (immobiliser code ECU). ○ - -
A malfunction in the communication lines between the ECM and ID code box (immobiliser code ECU). - ○ -
A matching communication code cannot be verified during communication between the ECM and ID code box (immobiliser code ECU). - - ○
Detection Time - -
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
·

B279986*1

·

B2799*2


-

*1: for 8NR-FTS

*2: for 3ZR-FAE


WIRING DIAGRAM

B424447E20
5.313,1.74 5.771,1.938 0.458,0.198 10 false IMI 5.302,0.833 5.76,1.031 0.458,0.198 10 false IMO 5.75,1.219 6.135,1.427 0.385,0.208 10 false 12 V 5.01,1.74 5.229,1.979 0.219,0.24 10 false 28 5.021,0.833 5.479,1.031 0.458,0.198 10 false 45 5.677,2.979 6.375,3.177 0.698,0.198 10 false ECM 5.677,2.792 6.531,2.979 0.854,0.188 10 false A38 1.594,0.833 2.052,1.031 0.458,0.198 10 false EFII 1.521,1.74 1.979,1.938 0.458,0.198 10 false EFIO 1.167,0.167 1.625,0.365 0.458,0.198 10 false 12 V 1.979,0.833 2.438,1.031 0.458,0.198 10 false 3 1.99,1.74 2.448,1.938 0.458,0.198 10 false 4 0.313,2.771 1.167,2.958 0.854,0.188 10 false F21 0.313,2.938 1.896,3.323 1.583,0.385 10 false ID Code Box (Immobiliser Code ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the ECM or ID code box (immobiliser code ECU), refer to Service Bulletin.

·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

When DTC B279986 and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID code.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

2.CLEAR DTC
2.CLEAR DTC
a.

for 8NR-FTS



b.

for 3ZR-FAE

i.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM (w/ Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Perform "DTC Output Confirmation Operation" procedure.


b.

for 8NR-FTS

i.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM (w/ Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 372
OK:

B279986 is not output.




c.

for 3ZR-FAE

i.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM (w/ Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
OK:

B2799 is not output.




Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
4.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
a.

Disconnect the F21 ID code box (immobiliser code ECU) connector.


b.

Disconnect the A38 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F21-4 (EFIO) - A38-28 (IMI) Always Below 1 Ω
F21-3 (EFII) - A38-45 (IMO) Always Below 1 Ω
F21-4 (EFIO) or A38-28 (IMI) - Body ground Always 10 kΩ or higher
F21-3 (EFII) or A38-45 (IMO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

6.REGISTER RECOGNITION CODE
6.REGISTER RECOGNITION CODE
a.

Register the recognition codes in the ECUs.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

7.REGISTER ECU COMMUNICATION ID
7.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER ENGINE STARTS
8.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts.

OK:

Engine starts normally.



Result:
Result Proceed to
OK A
NG (for 8NR-FTS) B
NG (for 3ZR-FAE) C



A

9.CLEAR DTC

B

C

9.CLEAR DTC
a.

for 8NR-FTS



b.

for 3ZR-FAE

i.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM (w/ Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234


Result:
Proceed to
NEXT



NEXT

10.CHECK FOR DTC
10.CHECK FOR DTC
a.

Perform "DTC Output Confirmation Operation" procedure.


b.

for 8NR-FTS

i.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM (w/ Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 372
OK:

B279986 is not output.




c.

for 3ZR-FAE

i.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM (w/ Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
OK:

B2799 is not output.




Result:
Result Proceed to
OK A
NG (for 8NR-FTS) B
NG (for 3ZR-FAE) C



A

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

B

C