Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2016.10–2019.09
RM32H0E _58 Vehicle Interior _060061 SUPPLEMENTAL RESTRAINT SYSTEMS _0294190 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1653/35  Seat Position Airbag Sensor Circuit Malfunction  


DESCRIPTION

The seat position airbag sensor circuit consists of the airbag sensor assembly and seat position airbag sensor.

DTC B1653/35 is stored when a malfunction is detected in the seat position airbag sensor circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1653/35 Seat Position Airbag Sensor Circuit Malfunction Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the seat position airbag sensor circuit.

·

The airbag sensor assembly detects a short to ground in the seat position airbag sensor circuit.

·

The airbag sensor assembly detects a short to B+ in the seat position airbag sensor circuit.

·

The airbag sensor assembly detects an open in the seat position airbag sensor circuit.

·

Seat position airbag sensor malfunction

·

Airbag sensor assembly malfunction


for LHD:
·

Floor wire

·

Front No. 2 seat wire LH

·

Seat position airbag sensor

·

Airbag sensor assembly


for RHD:
·

Floor wire

·

Front seat wire RH

·

Seat position airbag sensor

·

Airbag sensor assembly


Does not apply to test/check mode

DTC Detection Conditions:
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6
Diagnosis Condition Ignition switch ON ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the seat position airbag sensor circuit ○ - - - - -
The airbag sensor assembly detects a short to ground in the seat position airbag sensor circuit - ○ - - - -
The airbag sensor assembly detects a short to B+ in the seat position airbag sensor circuit - - ○ - - -
The airbag sensor assembly detects an open in the seat position airbag sensor circuit - - - ○ - -
Seat position airbag sensor malfunction - - - - ○ -
Airbag sensor assembly malfunction - - - - - ○
Detection Time - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

for LHD:


C360621E02
1.385,0.802 2,1 0.615,0.198 10 false LSP+ 1.417,1.969 2.031,2.167 0.615,0.198 10 false LSP- 1.885,0.802 2.052,1 0.167,0.198 10 false 2 1.917,1.969 2.083,2.167 0.167,0.198 10 false 1 0.427,2.917 1.042,3.115 0.615,0.198 10 false M49 0.427,3.094 2.344,3.344 1.917,0.25 10 false Seat Position Airbag Sensor 3.083,3.031 5,3.281 1.917,0.25 10 false *1: w/o Dual-stage SRS 3.104,3.427 5.021,3.677 1.917,0.25 10 false *2: w/ Dual-stage SRS 5.313,2.917 6.229,3.083 0.917,0.167 10 false M2*1, M1*2 5.323,3.125 6.99,3.375 1.667,0.25 10 false Airbag Sensor Assembly 5.427,2.094 6.042,2.292 0.615,0.198 10 false LSP- 5.417,0.927 6.031,1.125 0.615,0.198 10 false LSP+ 4.719,0.792 5.417,0.99 0.698,0.198 10 false 14*1, 9*2 4.625,1.958 5.323,2.156 0.698,0.198 10 false 13*1, 17*2


for RHD:


C348586E08
5.354,2.917 5.865,3.125 0.51,0.208 10 false M18 5.354,3.073 7.01,3.396 1.656,0.323 10 false Airbag Sensor Assembly 5.135,0.802 5.583,1.115 0.448,0.313 10 false 16 5.135,1.979 5.583,2.292 0.448,0.313 10 false 24 5.385,0.906 6.042,1.323 0.656,0.417 10 false RSP+ 5.385,2.073 6.042,2.49 0.656,0.417 10 false RSP- 3.406,0.906 4.063,1.323 0.656,0.417 10 false MY2 0.573,2.917 1.021,3.094 0.448,0.177 10 false Y3 0.563,3.073 2.635,3.396 2.073,0.323 10 false Seat Position Airbag Sensor 1.542,0.792 2.198,1.208 0.656,0.417 10 false VS 1.448,1.958 2.104,2.375 0.656,0.417 10 false GND 3.406,2.073 4.042,2.281 0.635,0.208 10 false MY2 3.5,0.708 3.948,1.021 0.448,0.313 10 false 2 3.5,1.875 3.948,2.188 0.448,0.313 10 false 1 1.854,0.792 2.51,1.208 0.656,0.417 10 false 2 1.854,1.958 2.51,2.375 0.656,0.417 10 false 1


CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Choose the model to be inspected.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK CONNECTORS

B

9.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (OPEN)
2.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and seat position airbag sensor. Also check that the connectors that link the front No. 2 seat wire LH and floor wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly and seat position airbag sensor. Also disconnect the connectors that link the front No. 2 seat wire LH and floor wire.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (OPEN)

NG

REPLACE WIRE HARNESS

3.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (OPEN)
a.

Connect the connectors that link the front No. 2 seat wire LH and floor wire.

C360611C01
1.25,0.5 1.667,0.75 0.417,0.25 4.479,0.5 4.833,0.76 0.354,0.26 4.333,2.917 4.667,3.167 0.333,0.25 0.833,2.917 1.167,3.167 0.333,0.25 1.75,1.083 1.99,0.99 false 5.125,0.688 5.292,0.688 false 2.042,0.781 2.417,0.333 true 2.125,0.792 2.417,0.75 true 5.333,0.333 5.542,0.552 true 5.417,1 5.552,0.771 true 4.667,3.417 4.958,3.094 true 5.417,3.417 5.115,3.104 true 1.917,3.417 1.604,3.073 true 1.167,3.417 1.448,3.073 true 0.625,0.083 0.938,0.417 0.313,0.333 12 false *A 3.927,0.104 4.24,0.354 0.313,0.25 12 false *B 0.865,1.885 1.177,2.042 0.313,0.156 10 false *1 2.635,1.885 2.948,2.042 0.313,0.156 10 false *2 1.552,1.031 1.865,1.188 0.313,0.156 10 false *3 1.365,0.542 1.698,0.781 0.333,0.24 10 false M2 1.208,0.177 1.521,0.333 0.313,0.156 10 false *a 0.865,2.615 1.177,2.771 0.313,0.156 10 false *b 4.542,0.542 4.875,0.781 0.333,0.24 10 false M1 4.521,0.104 4.833,0.26 0.313,0.156 10 false *a 4.365,2.615 4.677,2.771 0.313,0.156 10 false *b 4.906,0.604 5.219,0.76 0.313,0.156 10 false *3 4.323,1.615 4.635,1.771 0.313,0.156 10 false *1 6.208,1.865 6.521,2.021 0.313,0.156 10 false *2 0.885,2.958 1.365,3.125 0.479,0.167 10 false M49 4.385,2.958 4.865,3.125 0.479,0.167 10 false M49 0.906,3.417 1.385,3.583 0.479,0.167 10 false LSP- 1.917,3.438 2.396,3.604 0.479,0.167 10 false LSP+ 5.406,3.438 5.885,3.604 0.479,0.167 10 false LSP+ 4.396,3.458 4.875,3.625 0.479,0.167 10 false LSP- 5.094,1.021 5.573,1.188 0.479,0.167 10 false LSP- 4.979,0.167 5.458,0.333 0.479,0.167 10 false LSP+ 2.5,0.229 2.979,0.396 0.479,0.167 10 false LSP- 2.5,0.677 2.979,0.844 0.479,0.167 10 false LSP+ 1.229,1.875 1.396,2.042 0.167,0.167 10 false D 1.417,1.885 1.583,2.052 0.167,0.167 10 false C 2.104,1.885 2.271,2.052 0.167,0.167 10 false B 2.323,1.875 2.49,2.042 0.167,0.167 10 false A 5.833,1.604 6,1.771 0.167,0.167 10 false A 5.625,1.615 5.792,1.781 0.167,0.167 10 false B 4.948,1.615 5.115,1.781 0.167,0.167 10 false C 4.74,1.615 4.906,1.781 0.167,0.167 10 false D
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 Seat Position Airbag Sensor *2 Airbag Sensor Assembly
*3 Service Wire - -
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Seat Position Airbag Sensor)



b.

Using a service wire, connect terminals 9 (LSP+) and 17 (LSP-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M49-2 (LSP+) - M49-1 (LSP-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT)

NG

REPLACE FLOOR WIRE

4.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT)
a.

Disconnect the service wire from connector B.

C360612C01
0.833,2.167 1.167,2.417 0.333,0.25 4.24,2.25 4.573,2.5 0.333,0.25 1.333,2.75 1.635,2.396 true 2.083,2.75 1.802,2.396 true 5.417,2.75 5.167,2.396 true 4.667,2.75 5,2.396 true 0.688,0.177 1.021,0.49 0.333,0.313 12 false *A 3.844,0.177 4.156,0.448 0.313,0.271 12 false *B 0.844,1.094 1.156,1.25 0.313,0.156 10 false *1 2.875,1.094 3.188,1.25 0.313,0.156 10 false *2 0.865,1.771 1.177,1.927 0.313,0.156 10 false *a 1.167,1.094 1.323,1.25 0.156,0.156 10 false D 4.188,0.833 4.5,0.99 0.313,0.156 10 false *1 6.198,1.094 6.51,1.25 0.313,0.156 10 false *2 4.24,1.771 4.552,1.927 0.313,0.156 10 false *a 4.531,0.844 4.688,1 0.156,0.156 10 false D 4.771,0.844 4.927,1 0.156,0.156 10 false C 5.646,0.854 5.802,1.01 0.156,0.156 10 false B 5.896,0.854 6.052,1.01 0.156,0.156 10 false A 2.531,1.094 2.688,1.25 0.156,0.156 10 false A 2.281,1.094 2.438,1.25 0.156,0.156 10 false B 1.417,1.094 1.573,1.25 0.156,0.156 10 false C 1.021,2.76 1.51,2.948 0.49,0.188 10 false LSP- 4.396,2.771 4.885,2.958 0.49,0.188 10 false LSP- 2.063,2.781 2.552,2.969 0.49,0.188 10 false LSP+ 5.406,2.802 5.896,2.99 0.49,0.188 10 false LSP+ 0.875,2.208 1.365,2.396 0.49,0.188 10 false M49 4.292,2.292 4.781,2.479 0.49,0.188 10 false M49
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 Seat Position Airbag Sensor *2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Seat Position Airbag Sensor)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M49-2 (LSP+) - M49-1 (LSP-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO B+)

NG

REPLACE FLOOR WIRE

5.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO B+)
a.

Connect the cable to the negative (-) battery terminal.

C360612C01
0.833,2.167 1.167,2.417 0.333,0.25 4.24,2.25 4.573,2.5 0.333,0.25 1.333,2.75 1.635,2.396 true 2.083,2.75 1.802,2.396 true 5.417,2.75 5.167,2.396 true 4.667,2.75 5,2.396 true 0.688,0.177 1.021,0.49 0.333,0.313 12 false *A 3.844,0.177 4.156,0.448 0.313,0.271 12 false *B 0.844,1.094 1.156,1.25 0.313,0.156 10 false *1 2.875,1.094 3.188,1.25 0.313,0.156 10 false *2 0.865,1.771 1.177,1.927 0.313,0.156 10 false *a 1.167,1.094 1.323,1.25 0.156,0.156 10 false D 4.188,0.833 4.5,0.99 0.313,0.156 10 false *1 6.198,1.094 6.51,1.25 0.313,0.156 10 false *2 4.24,1.771 4.552,1.927 0.313,0.156 10 false *a 4.531,0.844 4.688,1 0.156,0.156 10 false D 4.771,0.844 4.927,1 0.156,0.156 10 false C 5.646,0.854 5.802,1.01 0.156,0.156 10 false B 5.896,0.854 6.052,1.01 0.156,0.156 10 false A 2.531,1.094 2.688,1.25 0.156,0.156 10 false A 2.281,1.094 2.438,1.25 0.156,0.156 10 false B 1.417,1.094 1.573,1.25 0.156,0.156 10 false C 1.021,2.76 1.51,2.948 0.49,0.188 10 false LSP- 4.396,2.771 4.885,2.958 0.49,0.188 10 false LSP- 2.063,2.781 2.552,2.969 0.49,0.188 10 false LSP+ 5.406,2.802 5.896,2.99 0.49,0.188 10 false LSP+ 0.875,2.208 1.365,2.396 0.49,0.188 10 false M49 4.292,2.292 4.781,2.479 0.49,0.188 10 false M49
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 Seat Position Airbag Sensor *2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Seat Position Airbag Sensor)
- -



b.

Turn the ignition switch ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M49-1 (LSP-) - Body ground Ignition switch ON Below 1 V
M49-2 (LSP+) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

6.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

6.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO GROUND)
a.

Measure the resistance according to the value(s) in the table below.

C360612C01
0.833,2.167 1.167,2.417 0.333,0.25 4.24,2.25 4.573,2.5 0.333,0.25 1.333,2.75 1.635,2.396 true 2.083,2.75 1.802,2.396 true 5.417,2.75 5.167,2.396 true 4.667,2.75 5,2.396 true 0.688,0.177 1.021,0.49 0.333,0.313 12 false *A 3.844,0.177 4.156,0.448 0.313,0.271 12 false *B 0.844,1.094 1.156,1.25 0.313,0.156 10 false *1 2.875,1.094 3.188,1.25 0.313,0.156 10 false *2 0.865,1.771 1.177,1.927 0.313,0.156 10 false *a 1.167,1.094 1.323,1.25 0.156,0.156 10 false D 4.188,0.833 4.5,0.99 0.313,0.156 10 false *1 6.198,1.094 6.51,1.25 0.313,0.156 10 false *2 4.24,1.771 4.552,1.927 0.313,0.156 10 false *a 4.531,0.844 4.688,1 0.156,0.156 10 false D 4.771,0.844 4.927,1 0.156,0.156 10 false C 5.646,0.854 5.802,1.01 0.156,0.156 10 false B 5.896,0.854 6.052,1.01 0.156,0.156 10 false A 2.531,1.094 2.688,1.25 0.156,0.156 10 false A 2.281,1.094 2.438,1.25 0.156,0.156 10 false B 1.417,1.094 1.573,1.25 0.156,0.156 10 false C 1.021,2.76 1.51,2.948 0.49,0.188 10 false LSP- 4.396,2.771 4.885,2.958 0.49,0.188 10 false LSP- 2.063,2.781 2.552,2.969 0.49,0.188 10 false LSP+ 5.406,2.802 5.896,2.99 0.49,0.188 10 false LSP+ 0.875,2.208 1.365,2.396 0.49,0.188 10 false M49 4.292,2.292 4.781,2.479 0.49,0.188 10 false M49
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 Seat Position Airbag Sensor *2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Seat Position Airbag Sensor)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
M49-1 (LSP-) - Body ground Always 1 MΩ or higher
M49-2 (LSP+) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK DTC

NG

REPLACE FLOOR WIRE

7.CHECK DTC
a.
C360613C01
0.177,0.125 0.51,0.375 0.333,0.25 12 false *A 0.26,1.594 0.594,1.833 0.333,0.24 12 false *B 0.458,0.729 0.771,0.885 0.313,0.156 10 false *1 2.615,0.75 2.927,0.906 0.313,0.156 10 false *2 0.469,2.208 0.781,2.365 0.313,0.156 10 false *1 2.625,2.51 2.938,2.667 0.313,0.156 10 false *2 0.844,0.74 1.073,0.906 0.229,0.167 10 false D 1,0.74 1.229,0.906 0.229,0.167 10 false C 2.063,0.729 2.292,0.896 0.229,0.167 10 false B 2.208,0.729 2.438,0.896 0.229,0.167 10 false A 2.219,2.219 2.448,2.385 0.229,0.167 10 false A 2.052,2.219 2.281,2.385 0.229,0.167 10 false B 1,2.208 1.229,2.375 0.229,0.167 10 false C 0.844,2.208 1.073,2.375 0.229,0.167 10 false D
*A w/o Dual-stage SRS
*B w/ Dual-stage SRS
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly and seat position airbag sensor.


b.

Connect the cable to the negative (-) battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the ignition switch off.


e.

Turn the ignition switch ON, and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1653/35 is not output.


HINT:

Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG

8.CHECK SEAT POSITION AIRBAG SENSOR
8.CHECK SEAT POSITION AIRBAG SENSOR
a.
C360613C01
0.177,0.125 0.51,0.375 0.333,0.25 12 false *A 0.26,1.594 0.594,1.833 0.333,0.24 12 false *B 0.458,0.729 0.771,0.885 0.313,0.156 10 false *1 2.615,0.75 2.927,0.906 0.313,0.156 10 false *2 0.469,2.208 0.781,2.365 0.313,0.156 10 false *1 2.625,2.51 2.938,2.667 0.313,0.156 10 false *2 0.844,0.74 1.073,0.906 0.229,0.167 10 false D 1,0.74 1.229,0.906 0.229,0.167 10 false C 2.063,0.729 2.292,0.896 0.229,0.167 10 false B 2.208,0.729 2.438,0.896 0.229,0.167 10 false A 2.219,2.219 2.448,2.385 0.229,0.167 10 false A 2.052,2.219 2.281,2.385 0.229,0.167 10 false B 1,2.208 1.229,2.375 0.229,0.167 10 false C 0.844,2.208 1.073,2.375 0.229,0.167 10 false D
*A w/o Dual-stage SRS
*B w/ Dual-stage SRS
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Replace the seat position airbag sensor with a known good one.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SEAT POSITION SENSOR>REMOVAL

HINT:

Perform the following inspection using known good parts from another vehicle if possible.



d.

Connect the cable to the negative (-) battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1653/35 is not output.


HINT:

Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Restore the seat position airbag sensor that was installed for testing to its original location.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SEAT POSITION SENSOR>REMOVAL


Result:
Proceed to
OK
NG



OK

NG

9.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (OPEN)
a.
C284677C10
0.604,0.667 0.958,0.917 0.354,0.25 0.542,3.594 0.896,3.844 0.354,0.25 2.115,0.802 2.5,0.5 true 2.104,1.083 2.5,1.333 true 1.083,4.25 1.5,3.792 true 2.167,4.25 1.698,3.792 true 2.792,0.927 2.458,0.927 false 0.438,2.448 0.833,2.781 0.396,0.333 10 false *1 2.646,2.167 2.958,2.583 0.313,0.417 10 false *2 2.823,0.844 3.125,1.167 0.302,0.323 10 false *3 0.521,0.167 0.833,0.5 0.313,0.333 10 false *a 0.344,3.229 0.656,3.552 0.313,0.323 10 false *b 2.094,4.25 2.51,4.583 0.417,0.333 10 false VS 2.531,1.25 3.115,1.573 0.583,0.323 10 false RSP- 0.656,0.708 1.125,1.031 0.469,0.323 10 false M18 2.177,2.469 2.49,2.885 0.313,0.417 10 false A 1.927,2.458 2.24,2.875 0.313,0.417 10 false B 1.583,2.458 1.896,2.875 0.313,0.417 10 false C 1.427,2.458 1.74,2.875 0.313,0.417 10 false D 1.083,2.458 1.396,2.875 0.313,0.417 10 false E 0.844,2.458 1.156,2.875 0.313,0.417 10 false F 2.531,0.417 3.031,0.75 0.5,0.333 10 false RSP+ 0.938,4.25 1.438,4.656 0.5,0.406 10 false GND 0.635,3.635 1.104,3.958 0.469,0.323 10 false Y3
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly
*3 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Seat Position Airbag Sensor)


Connect the connectors that link the front seat wire RH and floor wire.


b.

Using a service wire, connect terminals 16 (RSP+) and 24 (RSP-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y3-2 (VS) - Y3-1 (GND) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT)

NG

18.CHECK FLOOR WIRE (OPEN)
10.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT)
a.
C284678C09
0.531,2.156 0.896,2.406 0.365,0.25 1,2.917 1.438,2.417 true 2.083,2.917 1.667,2.417 true 0.427,0.969 0.76,1.219 0.333,0.25 10 false *1 2.667,0.677 3.063,1.01 0.396,0.333 10 false *2 0.354,1.74 0.75,2.156 0.396,0.417 10 false *a 2.198,0.969 2.594,1.302 0.396,0.333 10 false A 1.927,0.979 2.323,1.313 0.396,0.333 10 false B 1.583,0.979 1.979,1.313 0.396,0.333 10 false C 1.417,0.979 1.813,1.313 0.396,0.333 10 false D 1.073,0.979 1.469,1.313 0.396,0.333 10 false E 0.802,0.969 1.198,1.302 0.396,0.333 10 false F 2.01,2.917 2.49,3.25 0.479,0.333 10 false VS 0.844,2.917 1.51,3.25 0.667,0.333 10 false GND 0.625,2.198 1.292,2.531 0.667,0.333 10 false Y3
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Seat Position Airbag Sensor)


Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y3-2 (VS) - Y3-1 (GND) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO B+)

NG

17.CHECK FLOOR WIRE (SHORT)
11.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO B+)
a.
C284678C09
0.531,2.156 0.896,2.406 0.365,0.25 1,2.917 1.438,2.417 true 2.083,2.917 1.667,2.417 true 0.427,0.969 0.76,1.219 0.333,0.25 10 false *1 2.667,0.677 3.063,1.01 0.396,0.333 10 false *2 0.354,1.74 0.75,2.156 0.396,0.417 10 false *a 2.198,0.969 2.594,1.302 0.396,0.333 10 false A 1.927,0.979 2.323,1.313 0.396,0.333 10 false B 1.583,0.979 1.979,1.313 0.396,0.333 10 false C 1.417,0.979 1.813,1.313 0.396,0.333 10 false D 1.073,0.979 1.469,1.313 0.396,0.333 10 false E 0.802,0.969 1.198,1.302 0.396,0.333 10 false F 2.01,2.917 2.49,3.25 0.479,0.333 10 false VS 0.844,2.917 1.51,3.25 0.667,0.333 10 false GND 0.625,2.198 1.292,2.531 0.667,0.333 10 false Y3
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Seat Position Airbag Sensor)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Y3-2 (VS) - Body ground Ignition switch ON Below 1 V
Y3-1 (GND) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

12.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO GROUND)

NG

16.CHECK FLOOR WIRE (SHORT TO B+)
12.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO GROUND)
a.
C284678C09
0.531,2.156 0.896,2.406 0.365,0.25 1,2.917 1.438,2.417 true 2.083,2.917 1.667,2.417 true 0.427,0.969 0.76,1.219 0.333,0.25 10 false *1 2.667,0.677 3.063,1.01 0.396,0.333 10 false *2 0.354,1.74 0.75,2.156 0.396,0.417 10 false *a 2.198,0.969 2.594,1.302 0.396,0.333 10 false A 1.927,0.979 2.323,1.313 0.396,0.333 10 false B 1.583,0.979 1.979,1.313 0.396,0.333 10 false C 1.417,0.979 1.813,1.313 0.396,0.333 10 false D 1.073,0.979 1.469,1.313 0.396,0.333 10 false E 0.802,0.969 1.198,1.302 0.396,0.333 10 false F 2.01,2.917 2.49,3.25 0.479,0.333 10 false VS 0.844,2.917 1.51,3.25 0.667,0.333 10 false GND 0.625,2.198 1.292,2.531 0.667,0.333 10 false Y3
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Seat Position Airbag Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y3-2 (VS) - Body ground Always 1 MΩ or higher
Y3-1 (GND) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

13.CHECK DTC

NG

15.CHECK FLOOR WIRE (SHORT TO GROUND)
13.CHECK DTC
a.
C284676C01
0.531,1.229 0.906,1.531 0.375,0.302 10 false *1 2.635,0.938 2.979,1.26 0.344,0.323 10 false *2 2.198,1.219 2.542,1.542 0.344,0.323 10 false A 2.042,1.229 2.385,1.552 0.344,0.323 10 false B 1.594,1.229 1.938,1.552 0.344,0.323 10 false C 1.438,1.229 1.781,1.552 0.344,0.323 10 false D 0.99,1.229 1.333,1.552 0.344,0.323 10 false E 0.833,1.229 1.177,1.552 0.344,0.323 10 false F
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly and seat position airbag sensor.


b.

Connect the cable to the negative (-) battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the ignition switch off.


e.

Turn the ignition switch ON, and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1653/35 is not output.


HINT:

Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG

14.CHECK SEAT POSITION AIRBAG SENSOR
14.CHECK SEAT POSITION AIRBAG SENSOR
a.
C284676C01
0.531,1.229 0.906,1.531 0.375,0.302 10 false *1 2.635,0.938 2.979,1.26 0.344,0.323 10 false *2 2.198,1.219 2.542,1.542 0.344,0.323 10 false A 2.042,1.229 2.385,1.552 0.344,0.323 10 false B 1.594,1.229 1.938,1.552 0.344,0.323 10 false C 1.438,1.229 1.781,1.552 0.344,0.323 10 false D 0.99,1.229 1.333,1.552 0.344,0.323 10 false E 0.833,1.229 1.177,1.552 0.344,0.323 10 false F
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Replace the seat position airbag sensor with a known good one.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SEAT POSITION SENSOR>REMOVAL

HINT:

Perform the following inspection using known good parts from another vehicle if possible.



d.

Connect the cable to the negative (-) battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1653/35 is not output.


HINT:

Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Restore the seat position airbag sensor that was installed for testing to its original location.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SEAT POSITION SENSOR>REMOVAL


Result:
Proceed to
OK
NG



OK

NG

15.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C348591C03
0.833,2.083 1.333,2.333 0.5,0.25 1.958,0.938 1.958,0.521 1.958,0.521 1.792,0.521 false 1.167,0.938 1.167,0.521 1.167,0.521 1,0.521 false 1.406,2.823 1.719,2.344 true 2.375,2.823 2.094,2.344 true 0.271,0.885 0.698,1.156 0.427,0.271 10 false *1 2.854,0.646 3.219,1.073 0.365,0.427 10 false *2 0.844,0.438 1.354,0.865 0.51,0.427 10 false *3 1.635,0.438 2.073,0.802 0.438,0.365 10 false *4 0.74,1.635 1.156,1.927 0.417,0.292 10 false *a 0.938,2.125 1.354,2.417 0.417,0.292 10 false MY2 2.25,2.833 2.667,3.125 0.417,0.292 10 false RSP+ 1.26,2.833 1.677,3.125 0.417,0.292 10 false RSP- 2.458,0.896 2.823,1.323 0.365,0.427 10 false A 2.146,0.896 2.51,1.323 0.365,0.427 10 false B 1.677,0.896 2.042,1.323 0.365,0.427 10 false C 1.365,0.896 1.729,1.323 0.365,0.427 10 false D 0.896,0.896 1.26,1.323 0.365,0.427 10 false E 0.594,0.896 0.958,1.323 0.365,0.427 10 false F
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly
*3 Front Seat Wire RH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Seat Wire RH)


Disconnect the floor wire connector from the front seat wire RH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MY2-2 (RSP+) - Body ground Always 1 MΩ or higher
MY2-1 (RSP-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT SEAT WIRE RH

NG

REPLACE FLOOR WIRE

16.CHECK FLOOR WIRE (SHORT TO B+)
a.
C348591C03
0.833,2.083 1.333,2.333 0.5,0.25 1.958,0.938 1.958,0.521 1.958,0.521 1.792,0.521 false 1.167,0.938 1.167,0.521 1.167,0.521 1,0.521 false 1.406,2.823 1.719,2.344 true 2.375,2.823 2.094,2.344 true 0.271,0.885 0.698,1.156 0.427,0.271 10 false *1 2.854,0.646 3.219,1.073 0.365,0.427 10 false *2 0.844,0.438 1.354,0.865 0.51,0.427 10 false *3 1.635,0.438 2.073,0.802 0.438,0.365 10 false *4 0.74,1.635 1.156,1.927 0.417,0.292 10 false *a 0.938,2.125 1.354,2.417 0.417,0.292 10 false MY2 2.25,2.833 2.667,3.125 0.417,0.292 10 false RSP+ 1.26,2.833 1.677,3.125 0.417,0.292 10 false RSP- 2.458,0.896 2.823,1.323 0.365,0.427 10 false A 2.146,0.896 2.51,1.323 0.365,0.427 10 false B 1.677,0.896 2.042,1.323 0.365,0.427 10 false C 1.365,0.896 1.729,1.323 0.365,0.427 10 false D 0.896,0.896 1.26,1.323 0.365,0.427 10 false E 0.594,0.896 0.958,1.323 0.365,0.427 10 false F
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly
*3 Front Seat Wire RH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Seat Wire RH)


Disconnect the floor wire connector from the front seat wire RH.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
MY2-2 (RSP+) - Body ground Ignition switch ON Below 1 V
MY2-1 (RSP-) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE FRONT SEAT WIRE RH

NG

REPLACE FLOOR WIRE

17.CHECK FLOOR WIRE (SHORT)
a.
C348591C03
0.833,2.083 1.333,2.333 0.5,0.25 1.958,0.938 1.958,0.521 1.958,0.521 1.792,0.521 false 1.167,0.938 1.167,0.521 1.167,0.521 1,0.521 false 1.406,2.823 1.719,2.344 true 2.375,2.823 2.094,2.344 true 0.271,0.885 0.698,1.156 0.427,0.271 10 false *1 2.854,0.646 3.219,1.073 0.365,0.427 10 false *2 0.844,0.438 1.354,0.865 0.51,0.427 10 false *3 1.635,0.438 2.073,0.802 0.438,0.365 10 false *4 0.74,1.635 1.156,1.927 0.417,0.292 10 false *a 0.938,2.125 1.354,2.417 0.417,0.292 10 false MY2 2.25,2.833 2.667,3.125 0.417,0.292 10 false RSP+ 1.26,2.833 1.677,3.125 0.417,0.292 10 false RSP- 2.458,0.896 2.823,1.323 0.365,0.427 10 false A 2.146,0.896 2.51,1.323 0.365,0.427 10 false B 1.677,0.896 2.042,1.323 0.365,0.427 10 false C 1.365,0.896 1.729,1.323 0.365,0.427 10 false D 0.896,0.896 1.26,1.323 0.365,0.427 10 false E 0.594,0.896 0.958,1.323 0.365,0.427 10 false F
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly
*3 Front Seat Wire RH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Seat Wire RH)


Disconnect the floor wire connector from the front seat wire RH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MY2-2 (RSP+) - MY2-1 (RSP-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT SEAT WIRE RH

NG

REPLACE FLOOR WIRE

18.CHECK FLOOR WIRE (OPEN)
a.
C348590C03
0.604,3.427 0.979,3.646 0.375,0.219 0.563,0.49 0.906,0.708 0.344,0.219 2.75,0.875 2.333,0.875 false 2.385,0.5 2.031,0.75 true 2.375,1.25 2.021,0.99 true 1.458,3.677 1.156,4.146 true 1.833,3.677 2.115,4.156 true 1.917,2.458 1.917,2.042 1.917,2.042 1.75,2.042 false 1.146,2.469 1.146,2.052 1.146,2.052 0.979,2.052 false 0.281,2.448 0.677,2.76 0.396,0.313 10 false *1 2.802,2.135 3.156,2.542 0.354,0.406 10 false *2 0.833,1.979 1.271,2.365 0.438,0.385 10 false *3 1.615,1.969 2.021,2.313 0.406,0.344 10 false *4 2.781,0.792 3.219,1.146 0.438,0.354 10 false *5 0.542,0.146 0.958,0.667 0.417,0.521 10 false *a 0.365,3.115 0.781,3.417 0.417,0.302 10 false *b 0.615,0.521 1.052,0.875 0.438,0.354 10 false M18 2.417,0.417 2.875,0.771 0.458,0.354 10 false RSP+ 2.417,1.188 2.854,1.542 0.438,0.354 10 false RSP- 2,4.167 2.583,4.51 0.583,0.344 10 false RSP+ 1,4.167 1.458,4.531 0.458,0.365 10 false RSP- 0.656,3.458 1.094,3.813 0.438,0.354 10 false MY2 2.427,2.438 2.781,2.844 0.354,0.406 10 false A 2.125,2.438 2.479,2.844 0.354,0.406 10 false B 1.656,2.438 2.01,2.844 0.354,0.406 10 false C 1.344,2.438 1.698,2.844 0.354,0.406 10 false D 0.875,2.438 1.229,2.844 0.354,0.406 10 false E 0.563,2.438 0.917,2.844 0.354,0.406 10 false F
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly
*3 Front Seat Wire RH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Front Seat Wire RH)


Disconnect the floor wire connector from the front seat wire RH.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MY2-2 (RSP+) - MY2-1 (RSP-) Always Below 1 Ω



c.

Disconnect the service wire from the connector B.


Result:
Proceed to
OK
NG



OK

REPLACE FRONT SEAT WIRE RH

NG

REPLACE FLOOR WIRE