Home › Drivetrain › K313 (MULTIDRIVE / CVT) › SHIFT LEVER
RM32H0E _52 Drivetrain _059624 K313 MULTIDRIVE / CVT _0299315 SHIFT LEVER A

K313 MULTIDRIVE / CVT  SHIFT LEVER  REMOVAL  


PROCEDURE

Hide 1.SECURE VEHICLE

a.
C332327

Fully apply the parking brake and chock a wheel.

CAUTION:
·

Make sure to apply the parking brake and chock a wheel before performing this procedure.

·

If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.




Hide 2.REMOVE SHIFT LEVER CAP

a.
C364052C01
0.542,1.292 0.958,0.875 true 0.427,1.365 0.646,1.573 0.219,0.208 10 true *a
*a Protective Tape


Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws to remove the shift lever cap from the shift position indicator.

NOTICE:

Be careful not to damage the shift lever cap and instrument panel ornament.



b.

Move the shift lever to N.


Hide 33504F 3.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

Hide 4.REMOVE REAR CONSOLE BOX ASSEMBLY

Hide 86741A 5.REMOVE TELEMATICS TRANSCEIVER (w/ Telematics Transceiver)

Hide 6.REMOVE NO. 1 CONSOLE BOX MOUNTING BRACKET

a.
C364055

w/ Stereo Component Amplifier:

i.

Disengage the 3 clamps to separate the wire harness from the No. 1 console box mounting bracket.


ii.

Remove the 2 bolts and No. 1 console box mounting bracket from the vehicle body.



b.

w/o Stereo Component Amplifier:

i.
C366682

Disengage the 2 clamps to separate the wire harness from the No. 1 console box mounting bracket.


ii.

Remove the 2 bolts and No. 1 console box mounting bracket from the vehicle body.



Hide 33820B 7.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

for TMMT Made:

i.
C364051C01
0,0 0,0 false
V113147

Remove in this Direction


Disconnect the end of the transmission control cable assembly from the shift lever assembly.


ii.
C364050C01
1.115,1.927 1.448,1.594 true 0.885,1.896 1.073,2.094 0.188,0.198 10 true *1
*1 Slider
V100135

Push
V113147

Remove in this Direction


Push in the slider and remove the transmission control cable from the shift lever assembly as shown in the illustration.



b.

for TMC Made:

i.
C365188C01
0,0 0,0 false
V113147

Remove in this Direction


Disconnect the end of the transmission control cable assembly from the shift lever assembly.


ii.
C365189C02
1.563,1.646 1.604,1.375 true 1.458,1.656 1.677,1.844 0.219,0.188 10 true *1
*1 Slider
V100135

Turn approximately 180°
V113147

Remove in this Direction


Rotate the nut approximately 180° in the direction shown in the illustration, and while holding the nut in that position, disconnect the transmission control cable assembly from the shift lever plate.

NOTICE:

Rotating the nut too much will damage the internal spring, and the transmission control cable assembly will not be reusable. Do not turn the nut too far.




Hide 33530F 8.REMOVE FLOOR SHIFT SHIFT LEVER ASSEMBLY (for LHD)

a.
C364056

Disconnect the 2 connectors from the floor shift shift lever assembly.


b.

Disengage the 6 clamps to separate the wire harness from the floor shift shift lever assembly.


c.
C364059

Remove the 4 bolts and floor shift shift lever assembly from the vehicle body.


Hide 33530F 9.REMOVE FLOOR SHIFT SHIFT LEVER ASSEMBLY (for RHD)

a.
C364057

Disconnect the connector from the floor shift shift lever assembly.


b.

Disengage the 3 clamps to separate the wire harness from the floor shift shift lever assembly.


c.
C364058

w/ Stereo Component Amplifier:

i.

Disconnect the connector from the floor shift shift lever assembly.


ii.

Disengage the 2 clamps to separate the wire harness from the floor shift shift lever assembly.



d.
C366451

w/o Stereo Component Amplifier:

i.

Disconnect the connector from the floor shift shift lever assembly.


ii.

Disengage the clamp to separate the wire harness from the floor shift shift lever assembly.



e.
C366460

Remove the 4 bolts and floor shift shift lever assembly from the vehicle body.