Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › 2016.10–2019.09
RM32H0E _56 Audio / Visual / Telematics _060227 AUDIO / VIDEO _0295690 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B15D3  Stereo Component Amplifier Disconnected  


DESCRIPTION

The radio and display receiver assembly and stereo component amplifier assembly are connected by the AVC-LAN communication line.

This DTC is stored when an AVC-LAN communication error occurs between the radio and display receiver assembly and stereo component amplifier assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15D3 Stereo Component Amplifier Disconnected When either condition below is met:
·

The stereo component amplifier assembly is/was not connected while the ignition switch is/was on or ACC

·

Communication between the master unit and the stereo component amplifier assembly is not possible when the engine is started


·

Stereo component amplifier assembly power source circuit

·

AVC-LAN circuit between radio and display receiver assembly and stereo component amplifier assembly

·

Stereo component amplifier assembly

·

Radio and display receiver assembly

·

Harness or connector



HINT:

The radio and display receiver assembly is the master unit.


DTC Detection Conditions:
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition The ignition switch is/was ON or ACC ○ -
The engine is started - ○
Malfunction Status The stereo component amplifier assembly is/was not connected ○ -
Communication between the master unit and the stereo component amplifier assembly is not possible - ○
Detection Time - -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

E286973E11
0.563,0.375 2.396,0.573 1.833,0.198 10 false from Battery 0.583,0.948 2.417,1.146 1.833,0.198 10 false from Battery 0.375,1.531 2.208,1.729 1.833,0.198 10 false from ACC Relay 2.771,0.531 4.604,0.729 1.833,0.198 10 false AMP NO. 1 2.771,1.115 4.604,1.313 1.833,0.198 10 false AMP NO. 2 2.813,1.677 4.646,1.875 1.833,0.198 10 false ECU-ACC 2.156,2.958 2.51,3.177 0.354,0.219 10 false F125 2.167,3.125 3.865,3.51 1.698,0.385 10 false Radio and Display Receiver Assembly 5.438,4.021 6.646,4.531 1.208,0.51 10 false Stereo Component Amplifier Assembly 1.104,4.188 3.24,4.552 2.135,0.365 10 false : AVC-LAN Communication Line 3.208,2.271 3.823,2.469 0.615,0.198 10 false TX1+ 3.219,2.677 3.833,2.875 0.615,0.198 10 false TX1- 5.25,0.385 5.865,0.583 0.615,0.198 10 false F75 5.615,0.385 6.229,0.583 0.615,0.198 10 false +B 5.615,0.948 6.229,1.146 0.615,0.198 10 false +B2 5.635,1.521 6.25,1.719 0.615,0.198 10 false ACC 5.625,2.271 6.24,2.469 0.615,0.198 10 false TX+ 5.635,2.688 6.25,2.885 0.615,0.198 10 false TX- 5.625,3.219 6.24,3.417 0.615,0.198 10 false GND 5.625,3.635 6.24,3.833 0.615,0.198 10 false GND2 5.313,0.188 5.927,0.385 0.615,0.198 10 false 1 5.271,0.75 5.885,0.948 0.615,0.198 10 false 16 5.271,1.333 5.885,1.531 0.615,0.198 10 false 12 5.302,2.073 5.917,2.271 0.615,0.198 10 false 8 5.313,2.49 5.927,2.688 0.615,0.198 10 false 7 5.313,3.01 5.927,3.208 0.615,0.198 10 false 3 5.271,3.438 5.885,3.635 0.615,0.198 10 false 18 3.625,2.146 4.24,2.344 0.615,0.198 10 false 7 3.635,2.531 4.25,2.729 0.615,0.198 10 false 8 5.25,0.948 5.865,1.146 0.615,0.198 10 false F75 5.25,1.521 5.865,1.719 0.615,0.198 10 false F76 5.24,2.292 5.854,2.49 0.615,0.198 10 false F76 5.24,2.677 5.854,2.875 0.615,0.198 10 false F76 5.24,3.208 5.854,3.406 0.615,0.198 10 false F75 5.24,3.635 5.854,3.833 0.615,0.198 10 false F75

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK DTC
a.

If DTC B15C3 is output, perform troubleshooting for DTC B15C3 first.

Result:
Result Proceed to
DTC B15C3 is not output. A
DTC B15C3 is output. B




A

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result:
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B


HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.





A

3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

4.CHECK DTC
3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.



Result:
Proceed to
NEXT



NEXT

4.CHECK DTC
4.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)
5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)
a.

Disconnect the F75 and F76 stereo component amplifier assembly connectors.


b.
E317664C03
1.458,0.333 1.958,0.583 0.5,0.25 1.458,2.583 1.958,2.833 0.5,0.25 2.917,0.917 2.5,1.25 true 1.5,4 1.125,3.531 true 1.083,4 0.833,3.531 true 0.729,3.396 0.417,4 true 1.031,3.333 0.656,2.865 true 0.167,0.146 0.479,0.302 0.313,0.156 10 false *a 1.563,2.625 1.875,2.823 0.313,0.198 10 false F75 1.583,0.385 1.896,0.583 0.313,0.198 10 false F76 1.385,4.031 2,4.229 0.615,0.198 10 false GND2 0.313,2.781 0.927,2.979 0.615,0.198 10 false GND 0.99,4.031 1.448,4.229 0.458,0.198 10 false +B2 0.302,4.031 0.76,4.229 0.458,0.198 10 false +B 2.979,0.823 3.365,1.104 0.385,0.281 10 false ACC
*a Front view of wire harness connector
(to Stereo Component Amplifier Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F75-3 (GND) - Body ground Always Below 1 Ω
F75-18 (GND2) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F75-1 (+B) - F75-3 (GND) Always 11 to 14 V
F75-16 (+B2) - F75-3 (GND) Always 11 to 14 V
F76-12 (ACC) - F75-3 (GND) Ignition switch ACC 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the F125 radio and display receiver assembly connector.


b.

Disconnect the F76 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F125-7 (TX1+) - F76-8 (TX+) Always Below 1 Ω
F125-8 (TX1-) - F76-7 (TX-) Always Below 1 Ω
F125-7 (TX1+) - Body ground Always 10 kΩ or higher
F125-8 (TX1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Replace the stereo component amplifier assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG