Home › Drivetrain › K313F (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM
RM32H0E _52 Drivetrain _059618 K313F MULTIDRIVE / CVT _0300013 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K313F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P071000  Transmission Fluid Temperature Sensor "A" Circuit Range/Performance  


DESCRIPTION

The CVT fluid temperature sensor converts the fluid temperature into a resistance value which is detected by the ECM.

The sensor resistance changes with the CVT fluid temperature. As the temperature rises, the sensor resistance decreases. The ECM applies voltage to the temperature sensor through ECM terminal THO1 and calculates the fluid temperature based on the voltage signal.

HINT:

The CVT fluid temperature is likely to increase under conditions such as towing, climbing hills and in traffic.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P071000 Transmission Fluid Temperature Sensor "A" Circuit Range/Performance Either one of the following conditions is met (2 trip detection logic):
·

The intake air and engine coolant temperatures were more than -10°C (14°F) at engine start, and the CVT fluid temperature remains below 20°C (68°F) for 3 seconds when the vehicle has been driven for over 18 minutes and 7 km (4.375 miles).

·

The engine coolant temperature was less than 35°C (95°F) at engine start, and the CVT fluid temperature remains more than 100°C (212°F) for 10 seconds.


·

CVT fluid level

·

Continuously variable transaxle assembly (CVT fluid temperature sensor)


Comes on (Euro-OBD)
Does not come on (Except Euro-OBD)
DTC stored SAE Code:
P0711

DTC Detection Condition Patterns:
Vehicle Condition
Pattern 1 Pattern 2
Diagnostic Condition The intake air and engine coolant temperatures were more than -10°C (14°F) at engine start, and the vehicle has been driven for over 18 minutes at 7 km (4.375 miles). ○ -
The engine coolant temperature was less than 35°C (95°F) at engine start. - ○
Malfunction Condition The CVT fluid temperature remains below 20°C (68°F). ○ -
The CVT fluid temperature remains more than 100°C (212°F). - ○
Duration 3 seconds or more 10 seconds or more
Detection Logic 2 trip detection logic 2 trip detection logic

HINT:

This DTC is output when either of the above detection patterns is met.


MONITOR DESCRIPTION

The CVT fluid temperature sensor converts the CVT fluid temperature to an electrical resistance value. Based on the resistance, the ECM determines the CVT fluid temperature and detects open or short circuits in the CVT fluid temperature circuit.

After driving the vehicle for a certain period, the CVT fluid temperature should increase. If the CVT fluid temperature remains below 20°C (68°F), the ECM interprets this as a fault, illuminates the MIL*, and stores this DTC.

When the engine coolant temperature reaches 35°C (95°F) after a cold engine start, if the CVT fluid temperature is 100°C (212°F) or more, the ECM also determines this as a fault, illuminates the MIL*, and stores this DTC.

*: Euro-OBD

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Enter the following menus: Powertrain / Transmission / Data List / A/T Oil Temperature No.1.

5.

Drive the vehicle and check that the Data List value (A/T Oil Temperature No.1) is between 20 and 100°C (68 and 212°F).



PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P071000)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Trouble Codes.

Powertrain > Transmission > Trouble Codes
50001 373

e.

Read the DTCs using the GTS.

HINT:

If any DTCs other than P071000 are output, perform troubleshooting for those DTCs first.



Result:
Result Proceed to
Only DTC P071000 is output A
DTC P071000 and other DTCs are output B



A

2.CHECK CVT FLUID LEVEL

B

2.CHECK CVT FLUID LEVEL
a.

Check the CVT fluid level.

Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE FLUID>ADJUSTMENT

OK:

CVT fluid level is correct.



Result:
Proceed to
OK
NG



OK

3.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

NG

3.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

Result:
Proceed to
NEXT



NEXT