Home › Drivetrain › EC69 (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE SYSTEM › 2016.10–2019.09
RM32H0E _52 Drivetrain _060311 EC69 MANUAL TRANSMISSION / TRANSAXLE _0300017 MANUAL TRANSAXLE SYSTEM C

EC69 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE SYSTEM  P050031  Vehicle Speed Sensor "A" No Signal  


DESCRIPTION

Vehicles, which are equipped with ABS (Anti-lock Brake System), detect the vehicle speed using the skid control ECU (brake actuator assembly) and speed sensors. Each speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU (brake actuator assembly). The skid control ECU (brake actuator assembly) converts the wheel speed signals into a 4-pulse signal and transmits it to the ECM via the combination meter assembly. The ECM determines the vehicle speed based on the frequency of the pulse signal.

HINT:
·

Various systems use the vehicle speed signal distributed from the combination meter assembly. Check all the components possibly related to the speed signal.

·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems using the speed signal will not operate normally.



A115899E96
0.771,1.052 1.563,1.427 0.792,0.375 10 false from Speed Sensor 1.813,1.958 3.354,2.406 1.542,0.448 10 false Skid Control ECU (brake actuator assembly) 3.5,1.958 5.333,2.125 1.833,0.167 10 false Combination Meter Assembly 3.115,0.604 3.927,0.781 0.813,0.177 10 false 4-Pulse 5.042,0.604 5.854,0.781 0.813,0.177 10 false 4-Pulse 6.073,1.844 6.521,2.01 0.448,0.167 10 false ECM

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P050031 Vehicle Speed Sensor "A" No Signal While vehicle being driven, no vehicle speed sensor signal transmitted to ECM for 5.25 seconds (2 trip detection logic).
·

Open or short in speed signal circuit

·

Combination meter assembly

·

ECM


Does not come on DTC stored SAE Code:
P0500

MONITOR DESCRIPTION

If there is no speed signal from the combination meter assembly even though the ECM determines that the vehicle is being driven, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then stores a DTC.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

(a)

Turn the ignition switch to ON and wait for 3 seconds or more.

(b)

Drive the vehicle at 10 km/h (6.21 mph) or more for 5 seconds or more.




PROCEDURE

1.READ VALUE USING GTS (VEHICLE SPEED)
a.

Drive the vehicle and check whether the operation of the speedometer in the combination meter assembly is normal.

HINT:
·

The vehicle speed sensor is operating normally if the speedometer reading is normal.

·

If the speedometer does not operate, check it by following the diagnostic procedure for a malfunction of the speedometer.




b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Vehicle Speed.

Powertrain > Engine > Data List
Tester Display
Vehicle Speed
50003 372 212
Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed
·

This is the current vehicle speed.

·

The vehicle speed is detected using the wheel speed sensors.

·

Vehicle speed data is delayed when it is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped.



e.

Drive the vehicle.


f.

According to the display on the GTS, read the Data List.


OK:

The values displayed on the GTS and speedometer are equal.


Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the F4 combination meter assembly connector.


b.

Disconnect the A38 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-6 (+S) - A38-44 (SPD) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK METER / GAUGE SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK METER / GAUGE SYSTEM
a.

Proceed to Speed Signal Circuit in Meter/Gauge System.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit


Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.

Powertrain > Transmission > Clear DTCs
50002 373

d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the GTS on.


h.

Drive the vehicle for 6 seconds or more.


i.

Enter the following menus: Powertrain / Transmission / Trouble Codes.

Powertrain > Transmission > Trouble Codes
50001 373

j.

Read the DTCs.

HINT:

If no DTCs (no pending DTCs) are output, the repair has been successfully completed.



Result:
Proceed to
NEXT



NEXT

END