Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM32H0E _58 Vehicle Interior _060136 METER / GAUGE / DISPLAY _0294876 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Engine Oil Pressure Switch Circuit  


DESCRIPTION

The combination meter assembly and engine oil pressure switch assembly are connected via direct line. The combination meter assembly determines the engine oil pressure based on the engine oil pressure switch ON/OFF signal.

HINT:
·

The combination meter assembly receives various vehicle information signals from the ECM via CAN communication in order to output warnings.

·

The combination meter assembly operates the following to output oil pressure warnings:

(a)

Engine oil pressure warning light

(b)

Engine oil pressure warning buzzer

(c)

Engine oil pressure warning message on multi-information display




WIRING DIAGRAM

C369239E05
0.969,4.146 4.635,4.344 3.667,0.198 10 false : CAN Communication Line 2.438,2.885 2.792,3.073 0.354,0.188 10 false C28 2.438,3.052 3.698,3.448 1.26,0.396 10 false Engine Oil Pressure Switch Assembly 5.188,3.115 5.542,3.302 0.354,0.188 10 false F4 5.177,3.271 7.125,3.573 1.948,0.302 10 false Combination Meter Assembly 5.917,2.531 6.271,2.719 0.354,0.188 10 false I/F 5.219,2.417 5.573,2.604 0.354,0.188 10 false S 4.958,2.417 5.313,2.604 0.354,0.188 10 false 9 3.729,2.448 4.083,2.635 0.354,0.188 10 false 1 1.969,1.438 2.583,1.792 0.615,0.354 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

The following troubleshooting procedure is based on the assumption that the ECM is normal. Confirm that the SFI system is not malfunctioning before performing the following procedure.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.INSPECT ENGINE OIL PRESSURE SWITCH ASSEMBLY
a.

Remove the engine oil pressure switch assembly.

Click hereEngine / Hybrid System>3ZR-FAE (LUBRICATION)>OIL PRESSURE SWITCH>REMOVAL


b.

Inspect the engine oil pressure switch assembly.

Click hereEngine / Hybrid System>3ZR-FAE (LUBRICATION)>OIL PRESSURE SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ENGINE OIL PRESSURE SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPLACE ENGINE OIL PRESSURE SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (ENGINE OIL PRESSURE SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the F4 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-9 (S) - C28-1 Always Below 1 Ω
F4-9 (S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR