Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System with Side-mounted Air Conditioner Pressure Sensor)
RM32H0E _58 Vehicle Interior _059841 HEATING / AIR CONDITIONING _0298708 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System with Side-mounted Air Conditioner Pressure Sensor) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System with Side-mounted Air Conditioner Pressure Sensor)  B14B2  Lost Communication with Front Panel LIN  


DESCRIPTION

The air conditioning control assembly communicates with the air conditioning amplifier assembly via LIN communication.

If the LIN communication system malfunctions, the air conditioning amplifier assembly does not operate even if the air conditioning control assembly is operated.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B14B2 Lost Communication with Front Panel LIN Lost communication with air conditioning control assembly
·

Harness or connector between air conditioning control assembly and IG power source

·

Harness or connector between air conditioning control assembly and body ground

·

LIN communication system

·

Air conditioning control assembly

·

Air conditioning amplifier assembly


Memorized
(10 seconds or more)*

*: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.


WIRING DIAGRAM

E282266E42
1.635,0.875 2.25,1.073 0.615,0.198 10 false LIN1 1.698,1.406 2.313,1.604 0.615,0.198 10 false IG+ 1.625,1.927 2.24,2.125 0.615,0.198 10 false GND 2.021,1.313 2.396,1.542 0.375,0.229 10 false 10 2.01,1.823 2.604,2.094 0.594,0.271 10 false 16 2.625,1.552 3.688,1.844 1.063,0.292 10 false ECU-IG1 NO. 4 3.885,1.406 4.854,1.833 0.969,0.427 10 false from IG1-NO. 1 Relay 4.76,2.51 7.104,2.875 2.344,0.365 10 false Air Conditioning Amplifier Assembly 4.771,2.333 5.385,2.531 0.615,0.198 10 false F73 5.24,0.885 5.854,1.083 0.615,0.198 10 false LIN1 2.021,0.719 2.635,0.917 0.615,0.198 10 false 2 4.99,0.698 5.604,0.896 0.615,0.198 10 false 14 0.5,2.542 2.844,2.906 2.344,0.365 10 false Air Conditioning Control Assembly 0.51,2.375 1.125,2.573 0.615,0.198 10 false F61 0.938,3.198 2.729,3.479 1.792,0.281 10 false : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - IG POWER SOURCE)
a.

Disconnect the F61 air conditioning control assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F61-10 (IG+) - Body ground Ignition switch ON 11 to 14 V
F61-10 (IG+) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F61-16 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - AIR CONDITIONING CONTROL ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - AIR CONDITIONING CONTROL ASSEMBLY)
a.

Disconnect the F73 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F61-2 (LIN1) - F73-14 (LIN1) Always Below 1 Ω
F61-2 (LIN1) or F73-14 (LIN1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Reconnect the F73 air conditioning amplifier assembly connector.


b.

Turn the ignition switch to ON.


c.
E361433E03
1.74,0.333 2.208,0.594 0.469,0.26 2,2.24 1.646,1.406 true 0.938,2.156 1.542,1.292 true 1.833,0.385 2.292,0.583 0.458,0.198 10 false F73 0.75,2.208 1.208,2.406 0.458,0.198 10 false GND 1.99,2.292 2.448,2.49 0.458,0.198 10 false LIN1 0.417,4.063 0.875,4.26 0.458,0.198 10 false GND

Connect an oscilloscope to terminals F73-14 (LIN1) and F73-4 (GND) of the air conditioning amplifier assembly and check the waveform.

OK:

Waveform is similar to that shown in the illustration.


Item Content
Tool Setting 2 V/DIV., 20 ms./DIV.
Vehicle Condition Ignition switch ON


Result:
Proceed to
OK
NG



OK

5.INSPECT AIR CONDITIONING CONTROL ASSEMBLY

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

5.INSPECT AIR CONDITIONING CONTROL ASSEMBLY
a.

Reconnect the F61 air conditioning control assembly connector.


b.

Turn the ignition switch to ON.


c.

Connect an oscilloscope to terminals F61-2 (LIN1) and F61-16 (GND) of the air conditioning control assembly and check the waveform.

E357686C03
1.563,0.25 2.063,0.5 0.5,0.25 2.115,1.823 2.698,1.25 true 4.146,0.938 4.99,1.677 true 0.167,0.177 0.479,0.375 0.313,0.198 10 false *a 1.688,0.281 2,0.479 0.313,0.198 10 false F61 2.135,3.417 2.542,3.625 0.406,0.208 10 false GND 1.802,1.781 2.208,1.99 0.406,0.208 10 false GND 5.021,1.708 5.427,1.917 0.406,0.208 10 false LIN1
*a Component with harness connected
(Air Conditioning Control Assembly)
- -


OK:

Waveform is similar to that shown in the illustration.


Item Content
Tool Setting 2 V/DIV., 20 ms./DIV.
Vehicle Condition Ignition switch to ON


Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE AIR CONDITIONING CONTROL ASSEMBLY