Home › Engine / Hybrid System › 3ZR-FAE (COOLING) › COOLING FAN SYSTEM
RM32H0E _51 Engine / Hybrid System _060196 3ZR-FAE COOLING _0295090 COOLING FAN SYSTEM J

3ZR-FAE COOLING  COOLING FAN SYSTEM  Cooling Fan Circuit  


DESCRIPTION

The ECM calculates an appropriate cooling fan speed based on the engine coolant temperature, air conditioning switch condition, refrigerant pressure, engine speed and vehicle speed, and sends signals to the cooling fan ECU to regulate the cooling fan. The cooling fan ECU controls the cooling fan speed based on the duty ratio signal sent from the ECM. By basing its control on the operating conditions, the ECM can control the fan speed optimally using the cooling fan ECU, achieving both high cooling performance and quietness.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE ELECTRIC COOLING FAN)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Electric Cooling Fan.


e.

Check the operation of the cooling fan while operating it using the GTS.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Electric Cooling Fan
50004 61 16
OK:
Tester Operation Fan Operation
ON Cooling fan operates
OFF Cooling fan stops



Result:
Result Proceed to
OK A
Cooling fan does not operate B
Cooling fan does not stop C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT COOLING FAN MOTOR

C

11.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)
2.INSPECT COOLING FAN MOTOR

Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the A57 cooling fan ECU connector.


b.

Turn the ignition switch to ON.


c.
A266912C12
0.292,1.865 0.625,2.125 0.333,0.26 1.083,2.813 1.354,2.104 false 2.417,2.823 2.104,2.115 false 0.26,0.281 0.573,0.479 0.313,0.198 10 false *a 0.333,1.917 0.635,2.115 0.302,0.198 10 false A57 0.948,2.885 1.25,3.104 0.302,0.219 10 false +B1 2.375,2.896 2.688,3.094 0.313,0.198 10 false E1
*a Front view of wire harness connector
(to Cooling fan ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A57-1(+B1) - A57-3(E1) Ignition switch ON 11 to 14 V



d.

Reconnect the A57 cooling fan ECU connector.


Result:
Result
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)

NG

5.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)
a.

Disconnect the A38 ECM connector.


b.

Disconnect the A57 cooling fan ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A38-60(RFC) or A57-2(SI) - Body ground Always 10 kΩ or higher



d.

Reconnect the A57 cooling fan ECU connector.


e.

Reconnect the A38 ECM connector.


Result:
Result
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - BODY GROUND)
a.

Disconnect the A57 cooling fan ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A57-3(E1) - Body ground Always Below 1 Ω



c.

Reconnect the A57 cooling fan ECU connector.


Result:
Result
OK
NG



OK

6.INSPECT FAN NO. 1 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT FAN NO. 1 RELAY

Result:
Result
OK
NG



OK

7.INSPECT NO. 1 ENGINE ROOM RELAY BLOCK (FAN NO. 1 RELAY)

NG

REPLACE FAN NO. 1 RELAY

7.INSPECT NO. 1 ENGINE ROOM RELAY BLOCK (FAN NO. 1 RELAY)
a.

Remove the FAN NO. 1 relay from the No. 1 engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (FAN NO. 1 relay) - Body ground Always 11 to 14 V



c.

Reinstall the FAN NO. 1 relay.


Result:
Result
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - FAN NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - FAN NO. 1 RELAY)
a.

Disconnect the A57 cooling fan ECU connector.


b.

Remove the FAN NO. 1 relay from the No. 1 engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A57-1(+B1) - 5 (FAN NO. 1 relay) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A57-1 (+B) or 5 (FAN NO. 1 relay) - Body ground Always 10 kΩ or higher



d.

Reinstall the FAN NO. 1 relay to the No. 1 engine room relay block.


e.

Reconnect the A57 cooling fan ECU connector.


Result:
Result
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY - BODY GROUND)
a.

Remove the FAN NO. 1 relay from the No. 1 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (FAN NO. 1 relay) - Body ground Always Below 1 Ω



c.

Reinstall the FAN NO. 1 relay to the No. 1 engine room relay block.


Result:
Result
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Remove the FAN NO. 1 relay from the No. 1 engine room relay block.


b.

Disconnect the 3F instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
1 (FAN NO. 1 relay) - 3F-14 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
1 (FAN NO. 1 relay) or 3F-14 - Body ground Always 10 kΩ or higher



d.

Reconnect the 3F instrument panel junction block assembly connector.


e.

Reinstall the FAN NO. 1 relay.


Result:
Result
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)
a.

Disconnect the A38 ECM connector.


b.

Disconnect the A57 cooling fan ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A38-60(RFC) - A57-2(SI) Always Below 1 Ω



d.

Reconnect the A57 cooling fan ECU connector.


e.

Reconnect the A38 ECM connector.


Result:
Result
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)
a.

Disconnect the z7 cooling fan motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
z7-1(-) - Body ground Always 10 kΩ or higher



c.

Reconnect the z7 cooling fan motor connector.


Result:
Result
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG