Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › from 2018.05
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM D

8NR-FTS ENGINE CONTROL  SFI SYSTEM  VEHICLE CONTROL HISTORY  


DESCRIPTION (SFI SYSTEM)(w/ Differential Pressure Sensor)


·

Vehicle Control History is a function that captures and stores ECU data when triggered by specific vehicle behavior.

·

The number of possible stored Freeze Frame Data sets, whether multi Freeze Frame Data is available, the number of freeze frame points, Freeze Frame Data items, the ECU internal range, etc., is different depending on the stored group.

·

The stored data items for Vehicle Control History Freeze Frame Data are different depending on the stored group. When the value of a data item does not change across all points, only the value of the detection point will be displayed. The contents of the Freeze Frame Data is almost the same as that of the Data List.



PRECAUTIONS (SFI SYSTEM) (w/ Differential Pressure Sensor)


·

As Vehicle Control History may be overwritten whenever the trigger conditions are met, make sure to save Vehicle Control History before performing any inspections.

·

As Vehicle Control History may be stored when performing an Active Test, learning, etc., make sure to clear the Vehicle Control History before returning the vehicle to the customer.



CHECK VEHICLE CONTROL HISTORY (SFI SYSTEM) (w/ Differential Pressure Sensor)


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).

Powertrain > Engine > Utility
Tester Display
Vehicle Control History (RoB)
50005 372 55
HINT:

It is also possible to display Vehicle Control History during the Health Check, if "Store All Data" is selected.


Vehicle Control History Item
Code Item Trigger Description Stored Group Reference Inspection Procedure Link
X0856 GPF Rejuvenate Interruption When normal PM (Particulate Matter) regeneration stops 0A Check the Vehicle Control History Freeze Frame Data items "GPF Rejuvenate Impossibility History" (Click here)
X0857 GPF Rejuvenate Run Insufficiency The air-fuel ratio conditions are met at 60 km/h (37 mph) or more, but the temperature required for PM regeneration has not been reached 0A Check that the vehicle was driven in the specified manner, and then increase the vehicle speed and perform particulate filter rejuvenation again.
Refer to Particulate Filter Rejuvenate Procedure
(Click here)
X0858 Particulate Filter Differential Pressure High When the GPF upstream exhaust pressure measured by the differential pressure sensor (GPF differential pressure calibration value) exceeds the threshold value due to the accumulation of PM or ash (metal oxide)
HINT:

When this code is detected, output is limited and the "Reduced Engine Power" warning message is displayed on the multi-information display.


0A Refer to the P244B00 inspection procedure (Click here)
X0859 Particulate Filter Differential Pressure Too High When the GPF upstream exhaust pressure measured by the differential pressure sensor (GPF differential pressure calibration value) exceeds the threshold value due to further PM and ash being accumulated in the GPF after the GPF differential sensor determines the pressure is high (X0858)
HINT:

When this code is detected, output is limited and the "Reduced Engine Power" warning message is displayed on the multi-information display.


0A Refer to the P244B00 inspection procedure (Click here)
X085C Over Temperature Prevention when Particulate Filter Over Accumulation When the PM deposition ratio is at or above the specified value
HINT:

When this code is detected, output is limited and the "Reduced Engine Power" warning message is displayed on the multi-information display.


0A Refer to the P246300 inspection procedure (Click here)

Stored Data
Stored Group Number of Records Number of Freeze Frame Points Multi Freeze Frame Data Sampling Period Note
0A 4 code
HINT:
·

If the detection conditions for a code that is not currently stored are met, the code will be stored.

·

If the detection conditions for a code that is currently stored are met again in the same trip, the code will not be overwritten.

·

If the detection conditions for a code that is currently stored are met again in a different trip, the code will be overwritten.



1 point (multi freeze frame data not available) - The data can be cleared by using the GTS or by disconnecting the cable from the negative (-) battery terminal.

HINT:
·

Multi Freeze Frame Data makes it possible to display the engine condition (ECU data) both before and after the trigger detection point.

·

The number of available points differs depending on the stored group.

·

When the value of a data item does not change across all points, only the value at the detection point will be displayed.

·

Only 1 measurement point can be displayed for stored group 05 and 0A Freeze Frame Data.





CLEAR VEHICLE CONTROL HISTORY (SFI SYSTEM)


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (Clear).

NOTICE:

By performing this procedure, all stored Vehicle Control History items will be cleared.




VEHICLE CONTROL HISTORY FREEZE FRAME DATA (SFI SYSTEM) (w/ Differential Pressure Sensor)


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).

Powertrain > Engine > Utility
Tester Display
Vehicle Control History (RoB)
50005 372 55

e.

Select a vehicle control history item to access the applicable freeze frame data.


f.

Check the freeze frame Data recorded with the Vehicle Control History.

Vehicle Control History Data
A404635



CHECK VEHICLE CONTROL HISTORY (CHARGING SYSTEM)


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).

Powertrain > Engine > Utility
Tester Display
Vehicle Control History (RoB)
50005 372 55
Vehicle Control History Item
Code Tester Display Measurement Item Diagnostic Note
X0600 Auxiliary Battery Voltage Low at Start History of low battery voltage at engine control system start -
X0601 Auxiliary Battery Voltage Low at IG OFF History of low battery voltage when ignition switch off -
X0602 Auxiliary Battery Discharge at IG OFF History of battery becoming discharged when ignition switch off -
X0603 Auxiliary Battery Discharge at Running History of battery becoming discharged while vehicle being driven -



CLEAR VEHICLE CONTROL HISTORY (CHARGING SYSTEM)


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (Clear).

NOTICE:

By performing this procedure, all stored Vehicle Control History items will be cleared.




VEHICLE CONTROL HISTORY FREEZE FRAME DATA (CHARGING SYSTEM)


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Select a vehicle control history item to access the applicable freeze frame data.

Powertrain > Engine > Utility
Tester Display
Vehicle Control History (RoB)
50005 372 55

e.

Check the freeze frame Data recorded with the Vehicle Control History.

Vehicle Control History Data
GTS Display Description
Total Distance Traveled Driving distance
Total Distance Traveled - Unit Unit of driving distance
Initial Engine Battery Minimum Voltage Minimum voltage at engine start
Alternator Voltage - Non Active Test Requested voltage when the regulator forced operation is not executed
Alternator Output Duty Ratio LIN terminal output (power generation rate)
Auxiliary Battery Voltage Battery voltage
(+B, +B2 terminal)
Auxiliary Battery Integrated Current Battery capacity taking into account battery deterioration.
Smoothed Value of Auxiliary Battery Temperature Calculated battery fluid temperature by battery fluid temperature sensor
Auxiliary Battery Charge Rate Battery charge percentage calculated by battery sensor
Auxiliary Battery Charging Rate Accuracy Accuracy of battery charge percentage calculated by battery sensor
Auxiliary Battery Charging Capacity Battery charging capacity calculated by battery sensor
Charging Control Mode Status of charging control
Charging Control Working Factor Rate of charging control operation
Average Vehicle Speed during Trip Average vehicle speed after engine starts during the current trip
Auxiliary Battery Integrated Current during Trip Integrated current value detected by the battery state sensor during the current trip
Auxiliary Battery Charging Integrated Current when Trip before Last Integrated current charged during the previous trip
Auxiliary Battery Discharging Integrated Current when Trip before Last Integrated current discharged during the previous trip
Auxiliary Battery Capacity after IG ON Battery capacity immediately after ignition switch ON
Auxiliary Battery Capacity after IG OFF Battery capacity immediately after ignition switch off
Estimated Open Ended Auxiliary Battery Voltage when IG OFF Estimated battery release voltage calculated when ignition switch is off by the battery sensor
Auxiliary Battery Average Current during IG OFF Average current while parked (average value of current consumed from when the ignition switch is off until lit is ON)
IG OFF Time just before IG ON Parking duration (duration from when the ignition switch is off until it is ON)
Auxiliary Battery Average Current when Auxiliary Battery Voltage Low (during IG OFF) Average current when system judges that voltage is low while parked (average current value when the ignition switch is off until the system judges the voltage is low while parked)
IG OFF Time when Auxiliary Battery Voltage Low (during IG OFF) Parking duration when system judges that voltage is low while parked (duration from when the ignition switch is off until the system judges the voltage is low while parked)
Elapsed Time during Auxiliary Battery Voltage Low Duration that the voltage detected by the battery state sensor while the vehicle is in motion is below the threshold (example: 11 V)
Average Engine Speed Average engine speed after engine starts during the current trip



VEHICLE CONTROL HISTORY (SRS AIRBAG SYSTEM)


HINT:

A part of the control history can be confirmed using the vehicle control history.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>VEHICLE CONTROL HISTORY